Re: [PATCH V3 2/2] ata: ahci: ceva: Update the driver to support xilinx GT phy

[Michal Simek <michal.simek@xilinx.com>]

On 2/8/21 7:03 PM, Piyush Mehta wrote:
> SATA controller used in Xilinx ZynqMP platform uses xilinx GT phy
> which has 4 GT lanes and can be used by 4 peripherals at a time.
> SATA controller uses 1 GT phy lane among the 4 GT lanes. To configure
> the GT lane for the SATA controller, the below sequence is expected.
> 
> 1. Assert the SATA controller reset.
> 2. Configure the xilinx GT phy lane for SATA controller (phy_init).
> 3. De-assert the SATA controller reset.
> 4. Wait for PLL of the GT lane used by SATA to be locked (phy_power_on).
> 
> The ahci_platform_enable_resources() by default does the phy_init()
> and phy_power_on() but the default sequence doesn't work with Xilinx
> platforms. Because of this reason, updated the driver to support the
> new sequence.
> 
> Added cevapriv->rst check, for backward compatibility with the older
> sequence. If the reset controller is not available, then the SATA
> controller will configure with the older sequences.
> 
> Signed-off-by: Piyush Mehta <piyush.mehta@xilinx.com>
> ---
>  drivers/ata/ahci_ceva.c | 43 ++++++++++++++++++++++++++++++++++++++++---
>  1 file changed, 40 insertions(+), 3 deletions(-)
> 
> diff --git a/drivers/ata/ahci_ceva.c b/drivers/ata/ahci_ceva.c
> index b10fd4c..b980218 100644
> --- a/drivers/ata/ahci_ceva.c
> +++ b/drivers/ata/ahci_ceva.c
> @@ -12,6 +12,7 @@
>  #include <linux/module.h>
>  #include <linux/of_device.h>
>  #include <linux/platform_device.h>
> +#include <linux/reset.h>
>  #include "ahci.h"
>  
>  /* Vendor Specific Register Offsets */
> @@ -87,6 +88,7 @@ struct ceva_ahci_priv {
>  	u32 axicc;
>  	bool is_cci_enabled;
>  	int flags;
> +	struct reset_control *rst;
>  };
>  
>  static unsigned int ceva_ahci_read_id(struct ata_device *dev,
> @@ -202,13 +204,48 @@ static int ceva_ahci_probe(struct platform_device *pdev)
>  
>  	cevapriv->ahci_pdev = pdev;
>  
> +	cevapriv->rst = devm_reset_control_get_optional_exclusive(&pdev->dev,
> +								  NULL);
> +	if (IS_ERR(cevapriv->rst)) {
> +		if (PTR_ERR(cevapriv->rst) != -EPROBE_DEFER)
> +			dev_err(&pdev->dev, "failed to get reset: %ld\n",
> +				PTR_ERR(cevapriv->rst));
> +	}

nit: This can be handled via dev_err_probe() to simplify this logic here.
It was added by a787e5400a1c ("driver core: add device probe log
helper") but up to Jens if he wants this to be fixed.

> +
>  	hpriv = ahci_platform_get_resources(pdev, 0);
>  	if (IS_ERR(hpriv))
>  		return PTR_ERR(hpriv);
>  
> -	rc = ahci_platform_enable_resources(hpriv);
> -	if (rc)
> -		return rc;
> +	if (!cevapriv->rst) {
> +		rc = ahci_platform_enable_resources(hpriv);
> +		if (rc)
> +			return rc;
> +	} else {
> +		int i;
> +
> +		rc = ahci_platform_enable_clks(hpriv);
> +		if (rc)
> +			return rc;
> +		/* Assert the controller reset */
> +		reset_control_assert(cevapriv->rst);
> +
> +		for (i = 0; i < hpriv->nports; i++) {
> +			rc = phy_init(hpriv->phys[i]);
> +			if (rc)
> +				return rc;
> +		}
> +
> +		/* De-assert the controller reset */
> +		reset_control_deassert(cevapriv->rst);
> +
> +		for (i = 0; i < hpriv->nports; i++) {
> +			rc = phy_power_on(hpriv->phys[i]);
> +			if (rc) {
> +				phy_exit(hpriv->phys[i]);
> +				return rc;
> +			}
> +		}
> +	}
>  
>  	if (of_property_read_bool(np, "ceva,broken-gen2"))
>  		cevapriv->flags = CEVA_FLAG_BROKEN_GEN2;
> 

Acked-by: Michal Simek <michal.simek@xilinx.com>

Jens:  Can you please take a look at this patch if you see any other issue?

Thanks,
Michal