* [PATCH v3 0/8] arm64: zynqmp: Add support for existing Xilinx ZynqMP based boards
@ 2018-03-02 19:04 Michal Simek
2018-03-02 19:04 ` [PATCH v3 1/8] dt-bindings: xilinx: Add description for ZynqMP Michal Simek
` (7 more replies)
0 siblings, 8 replies; 12+ messages in thread
From: Michal Simek @ 2018-03-02 19:04 UTC (permalink / raw)
To: devicetree
Cc: monstr, Masahiro Yamada, Arnd Bergmann, linux-kernel,
Rob Herring, Will Deacon, Mark Rutland, Catalin Marinas,
linux-arm-kernel
Hi,
This patchset is adding all current existing Xilinx ZynqMP boards.
zcu* boards are customer boards. zc1* are mainly Xilinx internal boards
but some of them have been shared with customers. zc1751 is unique in
this set because it is based board with FMC card for silicon/hard IP
validation.
All boards are using the same default clock configuration till clock
driver is merged to mainline. Some boards also contain other components
which are not described because mainline driver haven't been merged yet.
For example nand, qspi, pinctrl and phy.
Please let me know if you see any issue with these boards.
Thanks,
Michal
Changes in v3:
- Remove usb and gpio aliases
- Use i2c-mux instead of i2cswitch on revB board
- Remove qspi comment from revB
- Remove gpio and usb aliases
- Use i2c-mux instead of i2cswitch - was done with zcu106
- Remove gpio and usb aliases
- remove gpio and usb aliases
- Remove usb and gpio aliases
- Remove aliases for can, usb, gpio
- dc2 fix spi_flashes and partitions
Changes in v2:
- New patch in this series
- Use i2c-mux instead of i2cswitch
- Remove i2c mw u-boot commands
- Use 96boards labels for i2cs and spis
- Fix pmic and wifi node
- Record compatible string to xilinx.txt
- Remove Nathalie's email (she left Xilinx already)
- Remove i2c mw u-boot commands
- Use i2c-mux instead of i2cswitch
- Use clock generator without numbers.
- Use dash in node name zcu102 rev1.0
- Record compatible string to xilinx.txt
- Remove i2c mw u-boot commands
- Record compatible string to xilinx.txt
- Remove i2c mw u-boot commands
- Use i2c-mux instead of i2cswitch
- Use clock generator without numbers
- Record compatible string to xilinx.txt
- Remove i2c mw u-boot commands
- Use i2c-mux instead of i2cswitch
- Use clock generator without numbers.
- Record compatible string to xilinx.txt
- Record compatible string to xilinx.txt
- Record compatible string to xilinx.txt
Michal Simek (8):
dt-bindings: xilinx: Add description for ZynqMP
arm64: zynqmp: Add support for Xilinx zcu100-revC
arm64: zynqmp: Add support for Xilinx zcu102
arm64: zynqmp: Add support for Xilinx zcu104-revA
arm64: zynqmp: Add support for Xilinx zcu106-revA
arm64: zynqmp: Add support for Xilinx zcu111-revA
arm64: zynqmp: Add support for Xilinx zc12XX boards
arm64: zynqmp: Add support for Xilinx zc1751
Documentation/devicetree/bindings/arm/xilinx.txt | 42 ++
arch/arm64/boot/dts/xilinx/Makefile | 15 +
arch/arm64/boot/dts/xilinx/zynqmp-clk.dtsi | 213 ++++++++
arch/arm64/boot/dts/xilinx/zynqmp-zc1232-revA.dts | 54 ++
arch/arm64/boot/dts/xilinx/zynqmp-zc1254-revA.dts | 42 ++
arch/arm64/boot/dts/xilinx/zynqmp-zc1275-revA.dts | 42 ++
.../boot/dts/xilinx/zynqmp-zc1751-xm015-dc1.dts | 131 +++++
.../boot/dts/xilinx/zynqmp-zc1751-xm016-dc2.dts | 168 +++++++
.../boot/dts/xilinx/zynqmp-zc1751-xm017-dc3.dts | 150 ++++++
.../boot/dts/xilinx/zynqmp-zc1751-xm018-dc4.dts | 178 +++++++
.../boot/dts/xilinx/zynqmp-zc1751-xm019-dc5.dts | 125 +++++
arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts | 289 +++++++++++
.../arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts | 36 ++
arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts | 548 +++++++++++++++++++++
arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts | 40 ++
arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts | 195 ++++++++
arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts | 522 ++++++++++++++++++++
arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts | 444 +++++++++++++++++
18 files changed, 3234 insertions(+)
create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-clk.dtsi
create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-zc1232-revA.dts
create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-zc1254-revA.dts
create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-zc1275-revA.dts
create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm015-dc1.dts
create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm016-dc2.dts
create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm017-dc3.dts
create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm018-dc4.dts
create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm019-dc5.dts
create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts
create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts
create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts
create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts
create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts
create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts
create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts
--
1.9.1
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH v3 1/8] dt-bindings: xilinx: Add description for ZynqMP
2018-03-02 19:04 [PATCH v3 0/8] arm64: zynqmp: Add support for existing Xilinx ZynqMP based boards Michal Simek
@ 2018-03-02 19:04 ` Michal Simek
2018-03-02 19:04 ` [PATCH v3 2/8] arm64: zynqmp: Add support for Xilinx zcu100-revC Michal Simek
` (6 subsequent siblings)
7 siblings, 0 replies; 12+ messages in thread
From: Michal Simek @ 2018-03-02 19:04 UTC (permalink / raw)
To: devicetree
Cc: monstr, linux-kernel, Rob Herring, Mark Rutland, linux-arm-kernel
Record xlnx,zynqmp compatible string.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
Changes in v3: None
Changes in v2:
- New patch in this series
Documentation/devicetree/bindings/arm/xilinx.txt | 10 ++++++++++
1 file changed, 10 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/xilinx.txt b/Documentation/devicetree/bindings/arm/xilinx.txt
index 1f7995357888..549e70a022cb 100644
--- a/Documentation/devicetree/bindings/arm/xilinx.txt
+++ b/Documentation/devicetree/bindings/arm/xilinx.txt
@@ -5,3 +5,13 @@ shall have the following properties.
Required root node properties:
- compatible = "xlnx,zynq-7000";
+
+---------------------------------------------------------------
+
+Xilinx Zynq UltraScale+ MPSoC Platforms Device Tree Bindings
+
+Boards with ZynqMP SOC based on an ARM Cortex A53 processor
+shall have the following properties.
+
+Required root node properties:
+ - compatible = "xlnx,zynqmp";
--
1.9.1
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH v3 2/8] arm64: zynqmp: Add support for Xilinx zcu100-revC
2018-03-02 19:04 [PATCH v3 0/8] arm64: zynqmp: Add support for existing Xilinx ZynqMP based boards Michal Simek
2018-03-02 19:04 ` [PATCH v3 1/8] dt-bindings: xilinx: Add description for ZynqMP Michal Simek
@ 2018-03-02 19:04 ` Michal Simek
2018-03-02 19:04 ` [PATCH v3 3/8] arm64: zynqmp: Add support for Xilinx zcu102 Michal Simek
` (5 subsequent siblings)
7 siblings, 0 replies; 12+ messages in thread
From: Michal Simek @ 2018-03-02 19:04 UTC (permalink / raw)
To: devicetree
Cc: monstr, Masahiro Yamada, linux-kernel, Arnd Bergmann,
Will Deacon, Catalin Marinas, Rob Herring, Mark Rutland,
linux-arm-kernel
This board has 2GB of memory, i2c, sd, wifi sdio, spis, uarts, display
port and usbs.
Board is using fixed clocks because clock driver hasn't been merged yet.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
Changes in v3:
- Remove usb and gpio aliases
Changes in v2:
- Use i2c-mux instead of i2cswitch
- Remove i2c mw u-boot commands
- Use 96boards labels for i2cs and spis
- Fix pmic and wifi node
- Record compatible string to xilinx.txt
- Remove Nathalie's email (she left Xilinx already)
Documentation/devicetree/bindings/arm/xilinx.txt | 6 +
arch/arm64/boot/dts/xilinx/Makefile | 1 +
arch/arm64/boot/dts/xilinx/zynqmp-clk.dtsi | 213 ++++++++++++++++
arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts | 289 ++++++++++++++++++++++
4 files changed, 509 insertions(+)
create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-clk.dtsi
create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts
diff --git a/Documentation/devicetree/bindings/arm/xilinx.txt b/Documentation/devicetree/bindings/arm/xilinx.txt
index 549e70a022cb..29039b645807 100644
--- a/Documentation/devicetree/bindings/arm/xilinx.txt
+++ b/Documentation/devicetree/bindings/arm/xilinx.txt
@@ -15,3 +15,9 @@ shall have the following properties.
Required root node properties:
- compatible = "xlnx,zynqmp";
+
+
+Additional compatible strings:
+
+- Xilinx 96boards compatible board zcu100
+ "xlnx,zynqmp-zcu100-revC", "xlnx,zynqmp-zcu100"
diff --git a/arch/arm64/boot/dts/xilinx/Makefile b/arch/arm64/boot/dts/xilinx/Makefile
index eba179b23b17..7266a6a9c0cd 100644
--- a/arch/arm64/boot/dts/xilinx/Makefile
+++ b/arch/arm64/boot/dts/xilinx/Makefile
@@ -1,2 +1,3 @@
# SPDX-License-Identifier: GPL-2.0
dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-ep108.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu100-revC.dtb
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-clk.dtsi b/arch/arm64/boot/dts/xilinx/zynqmp-clk.dtsi
new file mode 100644
index 000000000000..9c09baca7dd7
--- /dev/null
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-clk.dtsi
@@ -0,0 +1,213 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Clock specification for Xilinx ZynqMP
+ *
+ * (C) Copyright 2015 - 2018, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+/ {
+ clk100: clk100 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <100000000>;
+ };
+
+ clk125: clk125 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <125000000>;
+ };
+
+ clk200: clk200 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <200000000>;
+ };
+
+ clk250: clk250 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <250000000>;
+ };
+
+ clk300: clk300 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <300000000>;
+ };
+
+ clk600: clk600 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <600000000>;
+ };
+
+ dp_aclk: clock0 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <100000000>;
+ clock-accuracy = <100>;
+ };
+
+ dp_aud_clk: clock1 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <24576000>;
+ clock-accuracy = <100>;
+ };
+
+ dpdma_clk: dpdma_clk {
+ compatible = "fixed-clock";
+ #clock-cells = <0x0>;
+ clock-frequency = <533000000>;
+ };
+
+ drm_clock: drm_clock {
+ compatible = "fixed-clock";
+ #clock-cells = <0x0>;
+ clock-frequency = <262750000>;
+ clock-accuracy = <0x64>;
+ };
+};
+
+&can0 {
+ clocks = <&clk100 &clk100>;
+};
+
+&can1 {
+ clocks = <&clk100 &clk100>;
+};
+
+&fpd_dma_chan1 {
+ clocks = <&clk600>, <&clk100>;
+};
+
+&fpd_dma_chan2 {
+ clocks = <&clk600>, <&clk100>;
+};
+
+&fpd_dma_chan3 {
+ clocks = <&clk600>, <&clk100>;
+};
+
+&fpd_dma_chan4 {
+ clocks = <&clk600>, <&clk100>;
+};
+
+&fpd_dma_chan5 {
+ clocks = <&clk600>, <&clk100>;
+};
+
+&fpd_dma_chan6 {
+ clocks = <&clk600>, <&clk100>;
+};
+
+&fpd_dma_chan7 {
+ clocks = <&clk600>, <&clk100>;
+};
+
+&fpd_dma_chan8 {
+ clocks = <&clk600>, <&clk100>;
+};
+
+&lpd_dma_chan1 {
+ clocks = <&clk600>, <&clk100>;
+};
+
+&lpd_dma_chan2 {
+ clocks = <&clk600>, <&clk100>;
+};
+
+&lpd_dma_chan3 {
+ clocks = <&clk600>, <&clk100>;
+};
+
+&lpd_dma_chan4 {
+ clocks = <&clk600>, <&clk100>;
+};
+
+&lpd_dma_chan5 {
+ clocks = <&clk600>, <&clk100>;
+};
+
+&lpd_dma_chan6 {
+ clocks = <&clk600>, <&clk100>;
+};
+
+&lpd_dma_chan7 {
+ clocks = <&clk600>, <&clk100>;
+};
+
+&lpd_dma_chan8 {
+ clocks = <&clk600>, <&clk100>;
+};
+
+&gem0 {
+ clocks = <&clk125>, <&clk125>, <&clk125>;
+};
+
+&gem1 {
+ clocks = <&clk125>, <&clk125>, <&clk125>;
+};
+
+&gem2 {
+ clocks = <&clk125>, <&clk125>, <&clk125>;
+};
+
+&gem3 {
+ clocks = <&clk125>, <&clk125>, <&clk125>;
+};
+
+&gpio {
+ clocks = <&clk100>;
+};
+
+&i2c0 {
+ clocks = <&clk100>;
+};
+
+&i2c1 {
+ clocks = <&clk100>;
+};
+
+&sata {
+ clocks = <&clk250>;
+};
+
+&sdhci0 {
+ clocks = <&clk200 &clk200>;
+};
+
+&sdhci1 {
+ clocks = <&clk200 &clk200>;
+};
+
+&spi0 {
+ clocks = <&clk200 &clk200>;
+};
+
+&spi1 {
+ clocks = <&clk200 &clk200>;
+};
+
+&uart0 {
+ clocks = <&clk100 &clk100>;
+};
+
+&uart1 {
+ clocks = <&clk100 &clk100>;
+};
+
+&usb0 {
+ clocks = <&clk250>, <&clk250>;
+};
+
+&usb1 {
+ clocks = <&clk250>, <&clk250>;
+};
+
+&watchdog0 {
+ clocks = <&clk250>;
+};
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts
new file mode 100644
index 000000000000..3e862a9faf26
--- /dev/null
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts
@@ -0,0 +1,289 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * dts file for Xilinx ZynqMP ZCU100 revC
+ *
+ * (C) Copyright 2016 - 2018, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ * Nathalie Chan King Choy
+ */
+
+/dts-v1/;
+
+#include "zynqmp.dtsi"
+#include "zynqmp-clk.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "ZynqMP ZCU100 RevC";
+ compatible = "xlnx,zynqmp-zcu100-revC", "xlnx,zynqmp-zcu100", "xlnx,zynqmp";
+
+ aliases {
+ i2c0 = &i2c1;
+ rtc0 = &rtc;
+ serial0 = &uart1;
+ serial1 = &uart0;
+ serial2 = &dcc;
+ spi0 = &spi0;
+ spi1 = &spi1;
+ mmc0 = &sdhci0;
+ mmc1 = &sdhci1;
+ };
+
+ chosen {
+ bootargs = "earlycon";
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x80000000>;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ autorepeat;
+ sw4 {
+ label = "sw4";
+ gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_POWER>;
+ gpio-key,wakeup;
+ autorepeat;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ ds2 {
+ label = "ds2";
+ gpios = <&gpio 20 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+
+ ds3 {
+ label = "ds3";
+ gpios = <&gpio 19 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "phy0tx"; /* WLAN tx */
+ default-state = "off";
+ };
+
+ ds4 {
+ label = "ds4";
+ gpios = <&gpio 18 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "phy0rx"; /* WLAN rx */
+ default-state = "off";
+ };
+
+ ds5 {
+ label = "ds5";
+ gpios = <&gpio 17 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "bluetooth-power";
+ };
+
+ vbus_det { /* U5 USB5744 VBUS detection via MIO25 */
+ label = "vbus_det";
+ gpios = <&gpio 25 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+
+ bt_power {
+ label = "bt_power";
+ gpios = <&gpio 8 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+ };
+
+ wmmcsdio_fixed: fixedregulator-mmcsdio {
+ compatible = "regulator-fixed";
+ regulator-name = "wmmcsdio_fixed";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ sdio_pwrseq: sdio_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&gpio 7 GPIO_ACTIVE_LOW>; /* WIFI_EN */
+ };
+};
+
+&dcc {
+ status = "okay";
+};
+
+&gpio {
+ status = "okay";
+ gpio-line-names = "UART1_TX", "UART1_RX", "UART0_RX", "UART0_TX", "I2C1_SCL",
+ "I2C1_SDA", "SPI1_SCLK", "WLAN_EN", "BT_EN", "SPI1_CS",
+ "SPI1_MISO", "SPI1_MOSI", "I2C_MUX_RESET", "SD0_DAT0", "SD0_DAT1",
+ "SD0_DAT2", "SD0_DAT3", "PS_LED3", "PS_LED2", "PS_LED1",
+ "PS_LED0", "SD0_CMD", "SD0_CLK", "GPIO_PB", "SD0_DETECT",
+ "VBUS_DET", "POWER_INT", "DP_AUX", "DP_HPD", "DP_OE",
+ "DP_AUX_IN", "INA226_ALERT", "PS_FP_PWR_EN", "PL_PWR_EN", "POWER_KILL",
+ "", "GPIO-A", "GPIO-B", "SPI0_SCLK", "GPIO-C",
+ "GPIO-D", "SPI0_CS", "SPI0_MISO", "SPI_MOSI", "GPIO-E",
+ "GPIO-F", "SD1_D0", "SD1_D1", "SD1_D2", "SD1_D3",
+ "SD1_CMD", "SD1_CLK", "USB0_CLK", "USB0_DIR", "USB0_DATA2",
+ "USB0_NXT", "USB0_DATA0", "USB0_DATA1", "USB0_STP", "USB0_DATA3",
+ "USB0_DATA4", "USB0_DATA5", "USB0_DATA6", "USB0_DATA7", "USB1_CLK",
+ "USB1_DIR", "USB1_DATA2", "USB1_NXT", "USB1_DATA0", "USB1_DATA1",
+ "USB1_STP", "USB1_DATA3", "USB1_DATA4", "USB1_DATA5", "USB1_DATA6",
+ "USB_DATA7", "WLAN_IRQ", "PMIC_IRQ", /* MIO end and EMIO start */
+ "", "",
+ "", "", "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "", "", "",
+ "", "", "", "";
+};
+
+&i2c1 {
+ status = "okay";
+ clock-frequency = <100000>;
+ i2c-mux@75 { /* u11 */
+ compatible = "nxp,pca9548";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x75>;
+ i2csw_0: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ label = "LS-I2C0";
+ };
+ i2csw_1: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ label = "LS-I2C1";
+ };
+ i2csw_2: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ label = "HS-I2C2";
+ };
+ i2csw_3: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ label = "HS-I2C3";
+ };
+ i2csw_4: i2c@4 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x4>;
+
+ pmic: pmic@5e { /* Custom TI PMIC u33 */
+ compatible = "ti,tps65086";
+ reg = <0x5e>;
+ interrupt-parent = <&gpio>;
+ interrupts = <77 GPIO_ACTIVE_LOW>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ };
+ };
+ i2csw_5: i2c@5 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <5>;
+ /* PS_PMBUS */
+ ina226@40 { /* u35 */
+ compatible = "ti,ina226";
+ reg = <0x40>;
+ shunt-resistor = <10000>;
+ /* MIO31 is alert which should be routed to PMUFW */
+ };
+ };
+ i2csw_6: i2c@6 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <6>;
+ /*
+ * Not Connected
+ */
+ };
+ i2csw_7: i2c@7 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <7>;
+ /*
+ * usb5744 (DNP) - U5
+ * 100kHz - this is default freq for us
+ */
+ };
+ };
+};
+
+&rtc {
+ status = "okay";
+};
+
+/* SD0 only supports 3.3V, no level shifter */
+&sdhci0 {
+ status = "okay";
+ no-1-8-v;
+ broken-cd; /* CD has to be enabled by default */
+ disable-wp;
+};
+
+&sdhci1 {
+ status = "okay";
+ bus-width = <0x4>;
+ non-removable;
+ disable-wp;
+ cap-power-off-card;
+ mmc-pwrseq = <&sdio_pwrseq>;
+ vqmmc-supply = <&wmmcsdio_fixed>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ wlcore: wifi@2 {
+ compatible = "ti,wl1831";
+ reg = <2>;
+ interrupt-parent = <&gpio>;
+ interrupts = <76 IRQ_TYPE_EDGE_RISING>; /* MIO76 WLAN_IRQ 1V8 */
+ };
+};
+
+&spi0 { /* Low Speed connector */
+ status = "okay";
+ label = "LS-SPI0";
+};
+
+&spi1 { /* High Speed connector */
+ status = "okay";
+ label = "HS-SPI1";
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&uart1 {
+ status = "okay";
+
+};
+
+/* ULPI SMSC USB3320 */
+&usb0 {
+ status = "okay";
+};
+
+/* ULPI SMSC USB3320 */
+&usb1 {
+ status = "okay";
+};
+
+&watchdog0 {
+ status = "okay";
+};
--
1.9.1
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH v3 3/8] arm64: zynqmp: Add support for Xilinx zcu102
2018-03-02 19:04 [PATCH v3 0/8] arm64: zynqmp: Add support for existing Xilinx ZynqMP based boards Michal Simek
2018-03-02 19:04 ` [PATCH v3 1/8] dt-bindings: xilinx: Add description for ZynqMP Michal Simek
2018-03-02 19:04 ` [PATCH v3 2/8] arm64: zynqmp: Add support for Xilinx zcu100-revC Michal Simek
@ 2018-03-02 19:04 ` Michal Simek
2018-03-02 19:04 ` [PATCH v3 4/8] arm64: zynqmp: Add support for Xilinx zcu104-revA Michal Simek
` (4 subsequent siblings)
7 siblings, 0 replies; 12+ messages in thread
From: Michal Simek @ 2018-03-02 19:04 UTC (permalink / raw)
To: devicetree
Cc: monstr, Masahiro Yamada, linux-kernel, Arnd Bergmann,
Will Deacon, Catalin Marinas, Rob Herring, Mark Rutland,
linux-arm-kernel
This patch is adding revA, revB and rev1.0. There are also other
revisions between which should be backward compatible with previous
versions. Unfortunately all revs are still in use.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
Changes in v3:
- Use i2c-mux instead of i2cswitch on revB board
- Remove qspi comment from revB
- Remove gpio and usb aliases
Changes in v2:
- Remove i2c mw u-boot commands
- Use i2c-mux instead of i2cswitch
- Use clock generator without numbers.
- Use dash in node name zcu102 rev1.0
- Record compatible string to xilinx.txt
Documentation/devicetree/bindings/arm/xilinx.txt | 5 +
arch/arm64/boot/dts/xilinx/Makefile | 3 +
.../arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts | 36 ++
arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts | 548 +++++++++++++++++++++
arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts | 40 ++
5 files changed, 632 insertions(+)
create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts
create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts
create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts
diff --git a/Documentation/devicetree/bindings/arm/xilinx.txt b/Documentation/devicetree/bindings/arm/xilinx.txt
index 29039b645807..2b922ec3c82a 100644
--- a/Documentation/devicetree/bindings/arm/xilinx.txt
+++ b/Documentation/devicetree/bindings/arm/xilinx.txt
@@ -21,3 +21,8 @@ Additional compatible strings:
- Xilinx 96boards compatible board zcu100
"xlnx,zynqmp-zcu100-revC", "xlnx,zynqmp-zcu100"
+
+- Xilinx evaluation board zcu102
+ "xlnx,zynqmp-zcu102-revA", "xlnx,zynqmp-zcu102"
+ "xlnx,zynqmp-zcu102-revB", "xlnx,zynqmp-zcu102"
+ "xlnx,zynqmp-zcu102-rev1.0", "xlnx,zynqmp-zcu102"
diff --git a/arch/arm64/boot/dts/xilinx/Makefile b/arch/arm64/boot/dts/xilinx/Makefile
index 7266a6a9c0cd..24e3ce801304 100644
--- a/arch/arm64/boot/dts/xilinx/Makefile
+++ b/arch/arm64/boot/dts/xilinx/Makefile
@@ -1,3 +1,6 @@
# SPDX-License-Identifier: GPL-2.0
dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-ep108.dtb
dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu100-revC.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu102-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu102-revB.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu102-rev1.0.dtb
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts
new file mode 100644
index 000000000000..6647e97edba3
--- /dev/null
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts
@@ -0,0 +1,36 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * dts file for Xilinx ZynqMP ZCU102 Rev1.0
+ *
+ * (C) Copyright 2016 - 2018, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+#include "zynqmp-zcu102-revB.dts"
+
+/ {
+ model = "ZynqMP ZCU102 Rev1.0";
+ compatible = "xlnx,zynqmp-zcu102-rev1.0", "xlnx,zynqmp-zcu102", "xlnx,zynqmp";
+};
+
+&eeprom {
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ board_sn: board-sn@0 {
+ reg = <0x0 0x14>;
+ };
+
+ eth_mac: eth-mac@20 {
+ reg = <0x20 0x6>;
+ };
+
+ board_name: board-name@d0 {
+ reg = <0xd0 0x6>;
+ };
+
+ board_revision: board-revision@e0 {
+ reg = <0xe0 0x3>;
+ };
+};
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts
new file mode 100644
index 000000000000..5b4ffe646a9b
--- /dev/null
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts
@@ -0,0 +1,548 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * dts file for Xilinx ZynqMP ZCU102 RevA
+ *
+ * (C) Copyright 2015 - 2018, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+/dts-v1/;
+
+#include "zynqmp.dtsi"
+#include "zynqmp-clk.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "ZynqMP ZCU102 RevA";
+ compatible = "xlnx,zynqmp-zcu102-revA", "xlnx,zynqmp-zcu102", "xlnx,zynqmp";
+
+ aliases {
+ ethernet0 = &gem3;
+ i2c0 = &i2c0;
+ i2c1 = &i2c1;
+ mmc0 = &sdhci1;
+ rtc0 = &rtc;
+ serial0 = &uart0;
+ serial1 = &uart1;
+ serial2 = &dcc;
+ };
+
+ chosen {
+ bootargs = "earlycon";
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x80000000>, <0x8 0x00000000 0x0 0x80000000>;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ autorepeat;
+ sw19 {
+ label = "sw19";
+ gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
+ linux,code = <KEY_DOWN>;
+ gpio-key,wakeup;
+ autorepeat;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ heartbeat_led {
+ label = "heartbeat";
+ gpios = <&gpio 23 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+};
+
+&can1 {
+ status = "okay";
+};
+
+&dcc {
+ status = "okay";
+};
+
+&fpd_dma_chan1 {
+ status = "okay";
+};
+
+&fpd_dma_chan2 {
+ status = "okay";
+};
+
+&fpd_dma_chan3 {
+ status = "okay";
+};
+
+&fpd_dma_chan4 {
+ status = "okay";
+};
+
+&fpd_dma_chan5 {
+ status = "okay";
+};
+
+&fpd_dma_chan6 {
+ status = "okay";
+};
+
+&fpd_dma_chan7 {
+ status = "okay";
+};
+
+&fpd_dma_chan8 {
+ status = "okay";
+};
+
+&gem3 {
+ status = "okay";
+ phy-handle = <&phy0>;
+ phy-mode = "rgmii-id";
+ phy0: phy@21 {
+ reg = <21>;
+ ti,rx-internal-delay = <0x8>;
+ ti,tx-internal-delay = <0xa>;
+ ti,fifo-depth = <0x1>;
+ };
+};
+
+&gpio {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ tca6416_u97: gpio@20 {
+ compatible = "ti,tca6416";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ /*
+ * IRQ not connected
+ * Lines:
+ * 0 - PS_GTR_LAN_SEL0
+ * 1 - PS_GTR_LAN_SEL1
+ * 2 - PS_GTR_LAN_SEL2
+ * 3 - PS_GTR_LAN_SEL3
+ * 4 - PCI_CLK_DIR_SEL
+ * 5 - IIC_MUX_RESET_B
+ * 6 - GEM3_EXP_RESET_B
+ * 7, 10 - 17 - not connected
+ */
+
+ gtr_sel0 {
+ gpio-hog;
+ gpios = <0 0>;
+ output-low; /* PCIE = 0, DP = 1 */
+ line-name = "sel0";
+ };
+ gtr_sel1 {
+ gpio-hog;
+ gpios = <1 0>;
+ output-high; /* PCIE = 0, DP = 1 */
+ line-name = "sel1";
+ };
+ gtr_sel2 {
+ gpio-hog;
+ gpios = <2 0>;
+ output-high; /* PCIE = 0, USB0 = 1 */
+ line-name = "sel2";
+ };
+ gtr_sel3 {
+ gpio-hog;
+ gpios = <3 0>;
+ output-high; /* PCIE = 0, SATA = 1 */
+ line-name = "sel3";
+ };
+ };
+
+ tca6416_u61: gpio@21 {
+ compatible = "ti,tca6416";
+ reg = <0x21>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ /*
+ * IRQ not connected
+ * Lines:
+ * 0 - VCCPSPLL_EN
+ * 1 - MGTRAVCC_EN
+ * 2 - MGTRAVTT_EN
+ * 3 - VCCPSDDRPLL_EN
+ * 4 - MIO26_PMU_INPUT_LS
+ * 5 - PL_PMBUS_ALERT
+ * 6 - PS_PMBUS_ALERT
+ * 7 - MAXIM_PMBUS_ALERT
+ * 10 - PL_DDR4_VTERM_EN
+ * 11 - PL_DDR4_VPP_2V5_EN
+ * 12 - PS_DIMM_VDDQ_TO_PSVCCO_ON
+ * 13 - PS_DIMM_SUSPEND_EN
+ * 14 - PS_DDR4_VTERM_EN
+ * 15 - PS_DDR4_VPP_2V5_EN
+ * 16 - 17 - not connected
+ */
+ };
+
+ i2c-mux@75 { /* u60 */
+ compatible = "nxp,pca9544";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x75>;
+ i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ /* PS_PMBUS */
+ ina226@40 { /* u76 */
+ compatible = "ti,ina226";
+ reg = <0x40>;
+ shunt-resistor = <5000>;
+ };
+ ina226@41 { /* u77 */
+ compatible = "ti,ina226";
+ reg = <0x41>;
+ shunt-resistor = <5000>;
+ };
+ ina226@42 { /* u78 */
+ compatible = "ti,ina226";
+ reg = <0x42>;
+ shunt-resistor = <5000>;
+ };
+ ina226@43 { /* u87 */
+ compatible = "ti,ina226";
+ reg = <0x43>;
+ shunt-resistor = <5000>;
+ };
+ ina226@44 { /* u85 */
+ compatible = "ti,ina226";
+ reg = <0x44>;
+ shunt-resistor = <5000>;
+ };
+ ina226@45 { /* u86 */
+ compatible = "ti,ina226";
+ reg = <0x45>;
+ shunt-resistor = <5000>;
+ };
+ ina226@46 { /* u93 */
+ compatible = "ti,ina226";
+ reg = <0x46>;
+ shunt-resistor = <5000>;
+ };
+ ina226@47 { /* u88 */
+ compatible = "ti,ina226";
+ reg = <0x47>;
+ shunt-resistor = <5000>;
+ };
+ ina226@4a { /* u15 */
+ compatible = "ti,ina226";
+ reg = <0x4a>;
+ shunt-resistor = <5000>;
+ };
+ ina226@4b { /* u92 */
+ compatible = "ti,ina226";
+ reg = <0x4b>;
+ shunt-resistor = <5000>;
+ };
+ };
+ i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ /* PL_PMBUS */
+ ina226@40 { /* u79 */
+ compatible = "ti,ina226";
+ reg = <0x40>;
+ shunt-resistor = <2000>;
+ };
+ ina226@41 { /* u81 */
+ compatible = "ti,ina226";
+ reg = <0x41>;
+ shunt-resistor = <5000>;
+ };
+ ina226@42 { /* u80 */
+ compatible = "ti,ina226";
+ reg = <0x42>;
+ shunt-resistor = <5000>;
+ };
+ ina226@43 { /* u84 */
+ compatible = "ti,ina226";
+ reg = <0x43>;
+ shunt-resistor = <5000>;
+ };
+ ina226@44 { /* u16 */
+ compatible = "ti,ina226";
+ reg = <0x44>;
+ shunt-resistor = <5000>;
+ };
+ ina226@45 { /* u65 */
+ compatible = "ti,ina226";
+ reg = <0x45>;
+ shunt-resistor = <5000>;
+ };
+ ina226@46 { /* u74 */
+ compatible = "ti,ina226";
+ reg = <0x46>;
+ shunt-resistor = <5000>;
+ };
+ ina226@47 { /* u75 */
+ compatible = "ti,ina226";
+ reg = <0x47>;
+ shunt-resistor = <5000>;
+ };
+ };
+ i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ /* MAXIM_PMBUS - 00 */
+ max15301@a { /* u46 */
+ compatible = "maxim,max15301";
+ reg = <0xa>;
+ };
+ max15303@b { /* u4 */
+ compatible = "maxim,max15303";
+ reg = <0xb>;
+ };
+ max15303@10 { /* u13 */
+ compatible = "maxim,max15303";
+ reg = <0x10>;
+ };
+ max15301@13 { /* u47 */
+ compatible = "maxim,max15301";
+ reg = <0x13>;
+ };
+ max15303@14 { /* u7 */
+ compatible = "maxim,max15303";
+ reg = <0x14>;
+ };
+ max15303@15 { /* u6 */
+ compatible = "maxim,max15303";
+ reg = <0x15>;
+ };
+ max15303@16 { /* u10 */
+ compatible = "maxim,max15303";
+ reg = <0x16>;
+ };
+ max15303@17 { /* u9 */
+ compatible = "maxim,max15303";
+ reg = <0x17>;
+ };
+ max15301@18 { /* u63 */
+ compatible = "maxim,max15301";
+ reg = <0x18>;
+ };
+ max15303@1a { /* u49 */
+ compatible = "maxim,max15303";
+ reg = <0x1a>;
+ };
+ max15303@1d { /* u18 */
+ compatible = "maxim,max15303";
+ reg = <0x1d>;
+ };
+ max15303@20 { /* u8 */
+ compatible = "maxim,max15303";
+ status = "disabled"; /* unreachable */
+ reg = <0x20>;
+ };
+
+ max20751@72 { /* u95 */
+ compatible = "maxim,max20751";
+ reg = <0x72>;
+ };
+ max20751@73 { /* u96 */
+ compatible = "maxim,max20751";
+ reg = <0x73>;
+ };
+ };
+ /* Bus 3 is not connected */
+ };
+};
+
+&i2c1 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ /* PL i2c via PCA9306 - u45 */
+ i2c-mux@74 { /* u34 */
+ compatible = "nxp,pca9548";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x74>;
+ i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ /*
+ * IIC_EEPROM 1kB memory which uses 256B blocks
+ * where every block has different address.
+ * 0 - 256B address 0x54
+ * 256B - 512B address 0x55
+ * 512B - 768B address 0x56
+ * 768B - 1024B address 0x57
+ */
+ eeprom: eeprom@54 { /* u23 */
+ compatible = "atmel,24c08";
+ reg = <0x54>;
+ };
+ };
+ i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ si5341: clock-generator@36 { /* SI5341 - u69 */
+ reg = <0x36>;
+ };
+
+ };
+ i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ si570_1: clock-generator@5d { /* USER SI570 - u42 */
+ #clock-cells = <0>;
+ compatible = "silabs,si570";
+ reg = <0x5d>;
+ temperature-stability = <50>;
+ factory-fout = <300000000>;
+ clock-frequency = <300000000>;
+ };
+ };
+ i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ si570_2: clock-generator@5d { /* USER MGT SI570 - u56 */
+ #clock-cells = <0>;
+ compatible = "silabs,si570";
+ reg = <0x5d>;
+ temperature-stability = <50>; /* copy from zc702 */
+ factory-fout = <156250000>;
+ clock-frequency = <148500000>;
+ };
+ };
+ i2c@4 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <4>;
+ si5328: clock-generator@69 {/* SI5328 - u20 */
+ reg = <0x69>;
+ /*
+ * Chip has interrupt present connected to PL
+ * interrupt-parent = <&>;
+ * interrupts = <>;
+ */
+ };
+ };
+ /* 5 - 7 unconnected */
+ };
+
+ i2c-mux@75 {
+ compatible = "nxp,pca9548"; /* u135 */
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x75>;
+
+ i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ /* HPC0_IIC */
+ };
+ i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ /* HPC1_IIC */
+ };
+ i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ /* SYSMON */
+ };
+ i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ /* DDR4 SODIMM */
+ };
+ i2c@4 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <4>;
+ /* SEP 3 */
+ };
+ i2c@5 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <5>;
+ /* SEP 2 */
+ };
+ i2c@6 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <6>;
+ /* SEP 1 */
+ };
+ i2c@7 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <7>;
+ /* SEP 0 */
+ };
+ };
+};
+
+&pcie {
+ status = "okay";
+};
+
+&rtc {
+ status = "okay";
+};
+
+&sata {
+ status = "okay";
+ /* SATA OOB timing settings */
+ ceva,p0-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
+ ceva,p0-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
+ ceva,p0-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
+ ceva,p0-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
+ ceva,p1-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
+ ceva,p1-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
+ ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
+ ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
+};
+
+/* SD1 with level shifter */
+&sdhci1 {
+ status = "okay";
+ no-1-8-v;
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&uart1 {
+ status = "okay";
+};
+
+/* ULPI SMSC USB3320 */
+&usb0 {
+ status = "okay";
+};
+
+&watchdog0 {
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts
new file mode 100644
index 000000000000..af4d86882a5c
--- /dev/null
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts
@@ -0,0 +1,40 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * dts file for Xilinx ZynqMP ZCU102 RevB
+ *
+ * (C) Copyright 2016 - 2018, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+#include "zynqmp-zcu102-revA.dts"
+
+/ {
+ model = "ZynqMP ZCU102 RevB";
+ compatible = "xlnx,zynqmp-zcu102-revB", "xlnx,zynqmp-zcu102", "xlnx,zynqmp";
+};
+
+&gem3 {
+ phy-handle = <&phyc>;
+ phyc: phy@c {
+ reg = <0xc>;
+ ti,rx-internal-delay = <0x8>;
+ ti,tx-internal-delay = <0xa>;
+ ti,fifo-depth = <0x1>;
+ };
+ /* Cleanup from RevA */
+ /delete-node/ phy@21;
+};
+
+/* Fix collision with u61 */
+&i2c0 {
+ i2c-mux@75 {
+ i2c@2 {
+ max15303@1b { /* u8 */
+ compatible = "maxim,max15303";
+ reg = <0x1b>;
+ };
+ /delete-node/ max15303@20;
+ };
+ };
+};
--
1.9.1
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH v3 4/8] arm64: zynqmp: Add support for Xilinx zcu104-revA
2018-03-02 19:04 [PATCH v3 0/8] arm64: zynqmp: Add support for existing Xilinx ZynqMP based boards Michal Simek
` (2 preceding siblings ...)
2018-03-02 19:04 ` [PATCH v3 3/8] arm64: zynqmp: Add support for Xilinx zcu102 Michal Simek
@ 2018-03-02 19:04 ` Michal Simek
2018-03-07 20:31 ` Rob Herring
2018-03-02 19:04 ` [PATCH v3 5/8] arm64: zynqmp: Add support for Xilinx zcu106-revA Michal Simek
` (3 subsequent siblings)
7 siblings, 1 reply; 12+ messages in thread
From: Michal Simek @ 2018-03-02 19:04 UTC (permalink / raw)
To: devicetree
Cc: monstr, Masahiro Yamada, linux-kernel, Arnd Bergmann,
Will Deacon, Catalin Marinas, Rob Herring, Mark Rutland,
linux-arm-kernel
Xilinx zcu104 is another customer board. It is sort of zcu102 clone
with some differences.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
---
Changes in v3:
- Use i2c-mux instead of i2cswitch - was done with zcu106
- Remove gpio and usb aliases
Changes in v2:
- Remove i2c mw u-boot commands
- Record compatible string to xilinx.txt
Documentation/devicetree/bindings/arm/xilinx.txt | 3 +
arch/arm64/boot/dts/xilinx/Makefile | 1 +
arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts | 195 ++++++++++++++++++++++
3 files changed, 199 insertions(+)
create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts
diff --git a/Documentation/devicetree/bindings/arm/xilinx.txt b/Documentation/devicetree/bindings/arm/xilinx.txt
index 2b922ec3c82a..a9ce08a68711 100644
--- a/Documentation/devicetree/bindings/arm/xilinx.txt
+++ b/Documentation/devicetree/bindings/arm/xilinx.txt
@@ -26,3 +26,6 @@ Additional compatible strings:
"xlnx,zynqmp-zcu102-revA", "xlnx,zynqmp-zcu102"
"xlnx,zynqmp-zcu102-revB", "xlnx,zynqmp-zcu102"
"xlnx,zynqmp-zcu102-rev1.0", "xlnx,zynqmp-zcu102"
+
+- Xilinx evaluation board zcu104
+ "xlnx,zynqmp-zcu104-revA", "xlnx,zynqmp-zcu104"
diff --git a/arch/arm64/boot/dts/xilinx/Makefile b/arch/arm64/boot/dts/xilinx/Makefile
index 24e3ce801304..1c039e59c7c3 100644
--- a/arch/arm64/boot/dts/xilinx/Makefile
+++ b/arch/arm64/boot/dts/xilinx/Makefile
@@ -4,3 +4,4 @@ dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu100-revC.dtb
dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu102-revA.dtb
dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu102-revB.dtb
dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu102-rev1.0.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu104-revA.dtb
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts
new file mode 100644
index 000000000000..d4ad19a38c93
--- /dev/null
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts
@@ -0,0 +1,195 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * dts file for Xilinx ZynqMP ZCU104
+ *
+ * (C) Copyright 2017 - 2018, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+/dts-v1/;
+
+#include "zynqmp.dtsi"
+#include "zynqmp-clk.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "ZynqMP ZCU104 RevA";
+ compatible = "xlnx,zynqmp-zcu104-revA", "xlnx,zynqmp-zcu104", "xlnx,zynqmp";
+
+ aliases {
+ ethernet0 = &gem3;
+ i2c0 = &i2c1;
+ mmc0 = &sdhci1;
+ rtc0 = &rtc;
+ serial0 = &uart0;
+ serial1 = &uart1;
+ serial2 = &dcc;
+ };
+
+ chosen {
+ bootargs = "earlycon";
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x80000000>;
+ };
+};
+
+&can1 {
+ status = "okay";
+};
+
+&dcc {
+ status = "okay";
+};
+
+&gem3 {
+ status = "okay";
+ phy-handle = <&phy0>;
+ phy-mode = "rgmii-id";
+ phy0: phy@c {
+ reg = <0xc>;
+ ti,rx-internal-delay = <0x8>;
+ ti,tx-internal-delay = <0xa>;
+ ti,fifo-depth = <0x1>;
+ };
+};
+
+&gpio {
+ status = "okay";
+};
+
+&i2c1 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ /* Another connection to this bus via PL i2c via PCA9306 - u45 */
+ i2c-mux@74 { /* u34 */
+ compatible = "nxp,pca9548";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x74>;
+ i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ /*
+ * IIC_EEPROM 1kB memory which uses 256B blocks
+ * where every block has different address.
+ * 0 - 256B address 0x54
+ * 256B - 512B address 0x55
+ * 512B - 768B address 0x56
+ * 768B - 1024B address 0x57
+ */
+ eeprom@54 { /* u23 */
+ compatible = "atmel,24c08";
+ reg = <0x54>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+ };
+
+ i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ clock_8t49n287: clock-generator@6c { /* 8T49N287 - u182 */
+ reg = <0x6c>;
+ };
+ };
+
+ i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ irps5401_43: irps54012@43 { /* IRPS5401 - u175 */
+ reg = <0x43>;
+ };
+ irps5401_4d: irps54012@4d { /* IRPS5401 - u180 */
+ reg = <0x4d>;
+ };
+ };
+
+ i2c@4 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <4>;
+ tca6416_u97: gpio@21 {
+ compatible = "ti,tca6416";
+ reg = <0x21>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ /*
+ * IRQ not connected
+ * Lines:
+ * 0 - IRPS5401_ALERT_B
+ * 1 - HDMI_8T49N241_INT_ALM
+ * 2 - MAX6643_OT_B
+ * 3 - MAX6643_FANFAIL_B
+ * 5 - IIC_MUX_RESET_B
+ * 6 - GEM3_EXP_RESET_B
+ * 7 - FMC_LPC_PRSNT_M2C_B
+ * 4, 10 - 17 - not connected
+ */
+ };
+ };
+
+ i2c@5 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <5>;
+ };
+
+ i2c@7 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <7>;
+ };
+
+ /* 3, 6 not connected */
+ };
+};
+
+&rtc {
+ status = "okay";
+};
+
+&sata {
+ status = "okay";
+ /* SATA OOB timing settings */
+ ceva,p0-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
+ ceva,p0-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
+ ceva,p0-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
+ ceva,p0-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
+ ceva,p1-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
+ ceva,p1-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
+ ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
+ ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
+};
+
+/* SD1 with level shifter */
+&sdhci1 {
+ status = "okay";
+ no-1-8-v;
+ disable-wp;
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&uart1 {
+ status = "okay";
+};
+
+/* ULPI SMSC USB3320 */
+&usb0 {
+ status = "okay";
+};
+
+&watchdog0 {
+ status = "okay";
+};
--
1.9.1
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH v3 5/8] arm64: zynqmp: Add support for Xilinx zcu106-revA
2018-03-02 19:04 [PATCH v3 0/8] arm64: zynqmp: Add support for existing Xilinx ZynqMP based boards Michal Simek
` (3 preceding siblings ...)
2018-03-02 19:04 ` [PATCH v3 4/8] arm64: zynqmp: Add support for Xilinx zcu104-revA Michal Simek
@ 2018-03-02 19:04 ` Michal Simek
2018-03-07 20:32 ` Rob Herring
2018-03-02 19:04 ` [PATCH v3 6/8] arm64: zynqmp: Add support for Xilinx zcu111-revA Michal Simek
` (2 subsequent siblings)
7 siblings, 1 reply; 12+ messages in thread
From: Michal Simek @ 2018-03-02 19:04 UTC (permalink / raw)
To: devicetree
Cc: monstr, Masahiro Yamada, linux-kernel, Arnd Bergmann,
Will Deacon, Catalin Marinas, Rob Herring, Mark Rutland,
linux-arm-kernel
Xilinx zcu106 is a customer board. It is reusing some parts from zcu102.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
---
Changes in v3:
- remove gpio and usb aliases
Changes in v2:
- Remove i2c mw u-boot commands
- Use i2c-mux instead of i2cswitch
- Use clock generator without numbers
- Record compatible string to xilinx.txt
Documentation/devicetree/bindings/arm/xilinx.txt | 3 +
arch/arm64/boot/dts/xilinx/Makefile | 1 +
arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts | 522 ++++++++++++++++++++++
3 files changed, 526 insertions(+)
create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts
diff --git a/Documentation/devicetree/bindings/arm/xilinx.txt b/Documentation/devicetree/bindings/arm/xilinx.txt
index a9ce08a68711..8503fabf90ee 100644
--- a/Documentation/devicetree/bindings/arm/xilinx.txt
+++ b/Documentation/devicetree/bindings/arm/xilinx.txt
@@ -29,3 +29,6 @@ Additional compatible strings:
- Xilinx evaluation board zcu104
"xlnx,zynqmp-zcu104-revA", "xlnx,zynqmp-zcu104"
+
+- Xilinx evaluation board zcu106
+ "xlnx,zynqmp-zcu106-revA", "xlnx,zynqmp-zcu106"
diff --git a/arch/arm64/boot/dts/xilinx/Makefile b/arch/arm64/boot/dts/xilinx/Makefile
index 1c039e59c7c3..922c5da39600 100644
--- a/arch/arm64/boot/dts/xilinx/Makefile
+++ b/arch/arm64/boot/dts/xilinx/Makefile
@@ -5,3 +5,4 @@ dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu102-revA.dtb
dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu102-revB.dtb
dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu102-rev1.0.dtb
dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu104-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu106-revA.dtb
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts
new file mode 100644
index 000000000000..668f7f26716a
--- /dev/null
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts
@@ -0,0 +1,522 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * dts file for Xilinx ZynqMP ZCU106
+ *
+ * (C) Copyright 2016, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+/dts-v1/;
+
+#include "zynqmp.dtsi"
+#include "zynqmp-clk.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "ZynqMP ZCU106 RevA";
+ compatible = "xlnx,zynqmp-zcu106-revA", "xlnx,zynqmp-zcu106", "xlnx,zynqmp";
+
+ aliases {
+ ethernet0 = &gem3;
+ i2c0 = &i2c0;
+ i2c1 = &i2c1;
+ mmc0 = &sdhci1;
+ rtc0 = &rtc;
+ serial0 = &uart0;
+ serial1 = &uart1;
+ serial2 = &dcc;
+ };
+
+ chosen {
+ bootargs = "earlycon";
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x80000000>, <0x8 0x00000000 0x0 0x80000000>;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ autorepeat;
+ sw19 {
+ label = "sw19";
+ gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
+ linux,code = <KEY_DOWN>;
+ gpio-key,wakeup;
+ autorepeat;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ heartbeat_led {
+ label = "heartbeat";
+ gpios = <&gpio 23 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+};
+
+&can1 {
+ status = "okay";
+};
+
+&dcc {
+ status = "okay";
+};
+
+/* fpd_dma clk 667MHz, lpd_dma 500MHz */
+&fpd_dma_chan1 {
+ status = "okay";
+};
+
+&fpd_dma_chan2 {
+ status = "okay";
+};
+
+&fpd_dma_chan3 {
+ status = "okay";
+};
+
+&fpd_dma_chan4 {
+ status = "okay";
+};
+
+&fpd_dma_chan5 {
+ status = "okay";
+};
+
+&fpd_dma_chan6 {
+ status = "okay";
+};
+
+&fpd_dma_chan7 {
+ status = "okay";
+};
+
+&fpd_dma_chan8 {
+ status = "okay";
+};
+
+&gem3 {
+ status = "okay";
+ phy-handle = <&phy0>;
+ phy-mode = "rgmii-id";
+ phy0: phy@c {
+ reg = <0xc>;
+ ti,rx-internal-delay = <0x8>;
+ ti,tx-internal-delay = <0xa>;
+ ti,fifo-depth = <0x1>;
+ };
+};
+
+&gpio {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ tca6416_u97: gpio@20 {
+ compatible = "ti,tca6416";
+ reg = <0x20>;
+ gpio-controller; /* interrupt not connected */
+ #gpio-cells = <2>;
+ /*
+ * IRQ not connected
+ * Lines:
+ * 0 - SFP_SI5328_INT_ALM
+ * 1 - HDMI_SI5328_INT_ALM
+ * 5 - IIC_MUX_RESET_B
+ * 6 - GEM3_EXP_RESET_B
+ * 10 - FMC_HPC0_PRSNT_M2C_B
+ * 11 - FMC_HPC1_PRSNT_M2C_B
+ * 2-4, 7, 12-17 - not connected
+ */
+ };
+
+ tca6416_u61: gpio@21 {
+ compatible = "ti,tca6416";
+ reg = <0x21>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ /*
+ * IRQ not connected
+ * Lines:
+ * 0 - VCCPSPLL_EN
+ * 1 - MGTRAVCC_EN
+ * 2 - MGTRAVTT_EN
+ * 3 - VCCPSDDRPLL_EN
+ * 4 - MIO26_PMU_INPUT_LS
+ * 5 - PL_PMBUS_ALERT
+ * 6 - PS_PMBUS_ALERT
+ * 7 - MAXIM_PMBUS_ALERT
+ * 10 - PL_DDR4_VTERM_EN
+ * 11 - PL_DDR4_VPP_2V5_EN
+ * 12 - PS_DIMM_VDDQ_TO_PSVCCO_ON
+ * 13 - PS_DIMM_SUSPEND_EN
+ * 14 - PS_DDR4_VTERM_EN
+ * 15 - PS_DDR4_VPP_2V5_EN
+ * 16 - 17 - not connected
+ */
+ };
+
+ i2c-mux@75 { /* u60 */
+ compatible = "nxp,pca9544";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x75>;
+ i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ /* PS_PMBUS */
+ ina226@40 { /* u76 */
+ compatible = "ti,ina226";
+ reg = <0x40>;
+ shunt-resistor = <5000>;
+ };
+ ina226@41 { /* u77 */
+ compatible = "ti,ina226";
+ reg = <0x41>;
+ shunt-resistor = <5000>;
+ };
+ ina226@42 { /* u78 */
+ compatible = "ti,ina226";
+ reg = <0x42>;
+ shunt-resistor = <5000>;
+ };
+ ina226@43 { /* u87 */
+ compatible = "ti,ina226";
+ reg = <0x43>;
+ shunt-resistor = <5000>;
+ };
+ ina226@44 { /* u85 */
+ compatible = "ti,ina226";
+ reg = <0x44>;
+ shunt-resistor = <5000>;
+ };
+ ina226@45 { /* u86 */
+ compatible = "ti,ina226";
+ reg = <0x45>;
+ shunt-resistor = <5000>;
+ };
+ ina226@46 { /* u93 */
+ compatible = "ti,ina226";
+ reg = <0x46>;
+ shunt-resistor = <5000>;
+ };
+ ina226@47 { /* u88 */
+ compatible = "ti,ina226";
+ reg = <0x47>;
+ shunt-resistor = <5000>;
+ };
+ ina226@4a { /* u15 */
+ compatible = "ti,ina226";
+ reg = <0x4a>;
+ shunt-resistor = <5000>;
+ };
+ ina226@4b { /* u92 */
+ compatible = "ti,ina226";
+ reg = <0x4b>;
+ shunt-resistor = <5000>;
+ };
+ };
+ i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ /* PL_PMBUS */
+ ina226@40 { /* u79 */
+ compatible = "ti,ina226";
+ reg = <0x40>;
+ shunt-resistor = <2000>;
+ };
+ ina226@41 { /* u81 */
+ compatible = "ti,ina226";
+ reg = <0x41>;
+ shunt-resistor = <5000>;
+ };
+ ina226@42 { /* u80 */
+ compatible = "ti,ina226";
+ reg = <0x42>;
+ shunt-resistor = <5000>;
+ };
+ ina226@43 { /* u84 */
+ compatible = "ti,ina226";
+ reg = <0x43>;
+ shunt-resistor = <5000>;
+ };
+ ina226@44 { /* u16 */
+ compatible = "ti,ina226";
+ reg = <0x44>;
+ shunt-resistor = <5000>;
+ };
+ ina226@45 { /* u65 */
+ compatible = "ti,ina226";
+ reg = <0x45>;
+ shunt-resistor = <5000>;
+ };
+ ina226@46 { /* u74 */
+ compatible = "ti,ina226";
+ reg = <0x46>;
+ shunt-resistor = <5000>;
+ };
+ ina226@47 { /* u75 */
+ compatible = "ti,ina226";
+ reg = <0x47>;
+ shunt-resistor = <5000>;
+ };
+ };
+ i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ /* MAXIM_PMBUS - 00 */
+ max15301@a { /* u46 */
+ compatible = "maxim,max15301";
+ reg = <0xa>;
+ };
+ max15303@b { /* u4 */
+ compatible = "maxim,max15303";
+ reg = <0xb>;
+ };
+ max15303@10 { /* u13 */
+ compatible = "maxim,max15303";
+ reg = <0x10>;
+ };
+ max15301@13 { /* u47 */
+ compatible = "maxim,max15301";
+ reg = <0x13>;
+ };
+ max15303@14 { /* u7 */
+ compatible = "maxim,max15303";
+ reg = <0x14>;
+ };
+ max15303@15 { /* u6 */
+ compatible = "maxim,max15303";
+ reg = <0x15>;
+ };
+ max15303@16 { /* u10 */
+ compatible = "maxim,max15303";
+ reg = <0x16>;
+ };
+ max15303@17 { /* u9 */
+ compatible = "maxim,max15303";
+ reg = <0x17>;
+ };
+ max15301@18 { /* u63 */
+ compatible = "maxim,max15301";
+ reg = <0x18>;
+ };
+ max15303@1a { /* u49 */
+ compatible = "maxim,max15303";
+ reg = <0x1a>;
+ };
+ max15303@1b { /* u8 */
+ compatible = "maxim,max15303";
+ reg = <0x1b>;
+ };
+ max15303@1d { /* u18 */
+ compatible = "maxim,max15303";
+ reg = <0x1d>;
+ };
+
+ max20751@72 { /* u95 */
+ compatible = "maxim,max20751";
+ reg = <0x72>;
+ };
+ max20751@73 { /* u96 */
+ compatible = "maxim,max20751";
+ reg = <0x73>;
+ };
+ };
+ /* Bus 3 is not connected */
+ };
+};
+
+&i2c1 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ /* PL i2c via PCA9306 - u45 */
+ i2c-mux@74 { /* u34 */
+ compatible = "nxp,pca9548";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x74>;
+ i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ /*
+ * IIC_EEPROM 1kB memory which uses 256B blocks
+ * where every block has different address.
+ * 0 - 256B address 0x54
+ * 256B - 512B address 0x55
+ * 512B - 768B address 0x56
+ * 768B - 1024B address 0x57
+ */
+ eeprom: eeprom@54 { /* u23 */
+ compatible = "atmel,24c08";
+ reg = <0x54>;
+ };
+ };
+ i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ si5341: clock-generator@36 { /* SI5341 - u69 */
+ reg = <0x36>;
+ };
+
+ };
+ i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ si570_1: clock-generator@5d { /* USER SI570 - u42 */
+ #clock-cells = <0>;
+ compatible = "silabs,si570";
+ reg = <0x5d>;
+ temperature-stability = <50>;
+ factory-fout = <300000000>;
+ clock-frequency = <300000000>;
+ };
+ };
+ i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ si570_2: clock-generator@5d { /* USER MGT SI570 - u56 */
+ #clock-cells = <0>;
+ compatible = "silabs,si570";
+ reg = <0x5d>;
+ temperature-stability = <50>; /* copy from zc702 */
+ factory-fout = <156250000>;
+ clock-frequency = <148500000>;
+ };
+ };
+ i2c@4 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <4>;
+ si5328: clock-generator@69 {/* SI5328 - u20 */
+ reg = <0x69>;
+ };
+ };
+ i2c@5 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <5>; /* FAN controller */
+ temp@4c {/* lm96163 - u128 */
+ compatible = "national,lm96163";
+ reg = <0x4c>;
+ };
+ };
+ /* 6 - 7 unconnected */
+ };
+
+ i2c-mux@75 {
+ compatible = "nxp,pca9548"; /* u135 */
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x75>;
+
+ i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ /* HPC0_IIC */
+ };
+ i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ /* HPC1_IIC */
+ };
+ i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ /* SYSMON */
+ };
+ i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ /* DDR4 SODIMM */
+ };
+ i2c@4 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <4>;
+ /* SEP 3 */
+ };
+ i2c@5 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <5>;
+ /* SEP 2 */
+ };
+ i2c@6 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <6>;
+ /* SEP 1 */
+ };
+ i2c@7 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <7>;
+ /* SEP 0 */
+ };
+ };
+};
+
+&rtc {
+ status = "okay";
+};
+
+&sata {
+ status = "okay";
+ /* SATA OOB timing settings */
+ ceva,p0-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
+ ceva,p0-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
+ ceva,p0-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
+ ceva,p0-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
+ ceva,p1-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
+ ceva,p1-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
+ ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
+ ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
+};
+
+/* SD1 with level shifter */
+&sdhci1 {
+ status = "okay";
+ no-1-8-v;
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&uart1 {
+ status = "okay";
+};
+
+/* ULPI SMSC USB3320 */
+&usb0 {
+ status = "okay";
+};
+
+&watchdog0 {
+ status = "okay";
+};
--
1.9.1
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH v3 6/8] arm64: zynqmp: Add support for Xilinx zcu111-revA
2018-03-02 19:04 [PATCH v3 0/8] arm64: zynqmp: Add support for existing Xilinx ZynqMP based boards Michal Simek
` (4 preceding siblings ...)
2018-03-02 19:04 ` [PATCH v3 5/8] arm64: zynqmp: Add support for Xilinx zcu106-revA Michal Simek
@ 2018-03-02 19:04 ` Michal Simek
2018-03-02 19:04 ` [PATCH v3 7/8] arm64: zynqmp: Add support for Xilinx zc12XX boards Michal Simek
2018-03-02 19:04 ` [PATCH v3 8/8] arm64: zynqmp: Add support for Xilinx zc1751 Michal Simek
7 siblings, 0 replies; 12+ messages in thread
From: Michal Simek @ 2018-03-02 19:04 UTC (permalink / raw)
To: devicetree
Cc: monstr, Masahiro Yamada, linux-kernel, Arnd Bergmann,
Will Deacon, Catalin Marinas, Rob Herring, Mark Rutland,
linux-arm-kernel
Xilinx zcu111 is a customer board. It is reusing some parts from zcu102.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
Changes in v3:
- Remove usb and gpio aliases
Changes in v2:
- Remove i2c mw u-boot commands
- Use i2c-mux instead of i2cswitch
- Use clock generator without numbers.
- Record compatible string to xilinx.txt
Documentation/devicetree/bindings/arm/xilinx.txt | 3 +
arch/arm64/boot/dts/xilinx/Makefile | 1 +
arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts | 444 ++++++++++++++++++++++
3 files changed, 448 insertions(+)
create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts
diff --git a/Documentation/devicetree/bindings/arm/xilinx.txt b/Documentation/devicetree/bindings/arm/xilinx.txt
index 8503fabf90ee..c2bc75774010 100644
--- a/Documentation/devicetree/bindings/arm/xilinx.txt
+++ b/Documentation/devicetree/bindings/arm/xilinx.txt
@@ -32,3 +32,6 @@ Additional compatible strings:
- Xilinx evaluation board zcu106
"xlnx,zynqmp-zcu106-revA", "xlnx,zynqmp-zcu106"
+
+- Xilinx evaluation board zcu111
+ "xlnx,zynqmp-zcu111-revA", "xlnx,zynqmp-zcu111"
diff --git a/arch/arm64/boot/dts/xilinx/Makefile b/arch/arm64/boot/dts/xilinx/Makefile
index 922c5da39600..d15c9dc1d8f2 100644
--- a/arch/arm64/boot/dts/xilinx/Makefile
+++ b/arch/arm64/boot/dts/xilinx/Makefile
@@ -6,3 +6,4 @@ dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu102-revB.dtb
dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu102-rev1.0.dtb
dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu104-revA.dtb
dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu106-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu111-revA.dtb
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts
new file mode 100644
index 000000000000..9a9dd6a0142b
--- /dev/null
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts
@@ -0,0 +1,444 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * dts file for Xilinx ZynqMP ZCU111
+ *
+ * (C) Copyright 2017 - 2018, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+/dts-v1/;
+
+#include "zynqmp.dtsi"
+#include "zynqmp-clk.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "ZynqMP ZCU111 RevA";
+ compatible = "xlnx,zynqmp-zcu111-revA", "xlnx,zynqmp-zcu111", "xlnx,zynqmp";
+
+ aliases {
+ ethernet0 = &gem3;
+ i2c0 = &i2c0;
+ i2c1 = &i2c1;
+ mmc0 = &sdhci1;
+ rtc0 = &rtc;
+ serial0 = &uart0;
+ serial1 = &dcc;
+ };
+
+ chosen {
+ bootargs = "earlycon";
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x80000000>, <0x8 0x00000000 0x0 0x80000000>;
+ /* Another 4GB connected to PL */
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ autorepeat;
+ sw19 {
+ label = "sw19";
+ gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
+ linux,code = <KEY_DOWN>;
+ gpio-key,wakeup;
+ autorepeat;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ heartbeat_led {
+ label = "heartbeat";
+ gpios = <&gpio 23 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+};
+
+&dcc {
+ status = "okay";
+};
+
+&fpd_dma_chan1 {
+ status = "okay";
+};
+
+&fpd_dma_chan2 {
+ status = "okay";
+};
+
+&fpd_dma_chan3 {
+ status = "okay";
+};
+
+&fpd_dma_chan4 {
+ status = "okay";
+};
+
+&fpd_dma_chan5 {
+ status = "okay";
+};
+
+&fpd_dma_chan6 {
+ status = "okay";
+};
+
+&fpd_dma_chan7 {
+ status = "okay";
+};
+
+&fpd_dma_chan8 {
+ status = "okay";
+};
+
+&gem3 {
+ status = "okay";
+ phy-handle = <&phy0>;
+ phy-mode = "rgmii-id";
+ phy0: phy@c {
+ reg = <0xc>;
+ ti,rx-internal-delay = <0x8>;
+ ti,tx-internal-delay = <0xa>;
+ ti,fifo-depth = <0x1>;
+ };
+};
+
+&gpio {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ tca6416_u22: gpio@20 {
+ compatible = "ti,tca6416";
+ reg = <0x20>;
+ gpio-controller; /* interrupt not connected */
+ #gpio-cells = <2>;
+ /*
+ * IRQ not connected
+ * Lines:
+ * 0 - MAX6643_OT_B
+ * 1 - MAX6643_FANFAIL_B
+ * 2 - MIO26_PMU_INPUT_LS
+ * 4 - SFP_SI5382_INT_ALM
+ * 5 - IIC_MUX_RESET_B
+ * 6 - GEM3_EXP_RESET_B
+ * 10 - FMCP_HSPC_PRSNT_M2C_B
+ * 11 - CLK_SPI_MUX_SEL0
+ * 12 - CLK_SPI_MUX_SEL1
+ * 16 - IRPS5401_ALERT_B
+ * 17 - INA226_PMBUS_ALERT
+ * 3, 7, 13-15 - not connected
+ */
+ };
+
+ i2c-mux@75 { /* u23 */
+ compatible = "nxp,pca9544";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x75>;
+ i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ /* PS_PMBUS */
+ /* PMBUS_ALERT done via pca9544 */
+ ina226@40 { /* u67 */
+ compatible = "ti,ina226";
+ reg = <0x40>;
+ shunt-resistor = <2000>;
+ };
+ ina226@41 { /* u59 */
+ compatible = "ti,ina226";
+ reg = <0x41>;
+ shunt-resistor = <5000>;
+ };
+ ina226@42 { /* u61 */
+ compatible = "ti,ina226";
+ reg = <0x42>;
+ shunt-resistor = <5000>;
+ };
+ ina226@43 { /* u60 */
+ compatible = "ti,ina226";
+ reg = <0x43>;
+ shunt-resistor = <5000>;
+ };
+ ina226@45 { /* u64 */
+ compatible = "ti,ina226";
+ reg = <0x45>;
+ shunt-resistor = <5000>;
+ };
+ ina226@46 { /* u69 */
+ compatible = "ti,ina226";
+ reg = <0x46>;
+ shunt-resistor = <2000>;
+ };
+ ina226@47 { /* u66 */
+ compatible = "ti,ina226";
+ reg = <0x47>;
+ shunt-resistor = <5000>;
+ };
+ ina226@48 { /* u65 */
+ compatible = "ti,ina226";
+ reg = <0x48>;
+ shunt-resistor = <5000>;
+ };
+ ina226@49 { /* u63 */
+ compatible = "ti,ina226";
+ reg = <0x49>;
+ shunt-resistor = <5000>;
+ };
+ ina226@4a { /* u3 */
+ compatible = "ti,ina226";
+ reg = <0x4a>;
+ shunt-resistor = <5000>;
+ };
+ ina226@4b { /* u71 */
+ compatible = "ti,ina226";
+ reg = <0x4b>;
+ shunt-resistor = <5000>;
+ };
+ ina226@4c { /* u77 */
+ compatible = "ti,ina226";
+ reg = <0x4c>;
+ shunt-resistor = <5000>;
+ };
+ ina226@4d { /* u73 */
+ compatible = "ti,ina226";
+ reg = <0x4d>;
+ shunt-resistor = <5000>;
+ };
+ ina226@4e { /* u79 */
+ compatible = "ti,ina226";
+ reg = <0x4e>;
+ shunt-resistor = <5000>;
+ };
+ };
+ i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ /* NC */
+ };
+ i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ irps5401_43: irps54012@43 { /* IRPS5401 - u53 check these */
+ reg = <0x43>;
+ };
+ irps5401_44: irps54012@44 { /* IRPS5401 - u55 */
+ reg = <0x44>;
+ };
+ irps5401_45: irps54012@45 { /* IRPS5401 - u57 */
+ reg = <0x45>;
+ };
+ /* u68 IR38064 +0 */
+ /* u70 IR38060 +1 */
+ /* u74 IR38060 +2 */
+ /* u75 IR38060 +6 */
+ /* J19 header too */
+
+ };
+ i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ /* SYSMON */
+ };
+ };
+};
+
+&i2c1 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ i2c-mux@74 { /* u26 */
+ compatible = "nxp,pca9548";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x74>;
+ i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ /*
+ * IIC_EEPROM 1kB memory which uses 256B blocks
+ * where every block has different address.
+ * 0 - 256B address 0x54
+ * 256B - 512B address 0x55
+ * 512B - 768B address 0x56
+ * 768B - 1024B address 0x57
+ */
+ eeprom: eeprom@54 { /* u88 */
+ compatible = "atmel,24c08";
+ reg = <0x54>;
+ };
+ };
+ i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ si5341: clock-generator@36 { /* SI5341 - u46 */
+ reg = <0x36>;
+ };
+
+ };
+ i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ si570_1: clock-generator@5d { /* USER SI570 - u47 */
+ #clock-cells = <0>;
+ compatible = "silabs,si570";
+ reg = <0x5d>;
+ temperature-stability = <50>;
+ factory-fout = <300000000>;
+ clock-frequency = <300000000>;
+ };
+ };
+ i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ si570_2: clock-generator@5d { /* USER MGT SI570 - u49 */
+ #clock-cells = <0>;
+ compatible = "silabs,si570";
+ reg = <0x5d>;
+ temperature-stability = <50>;
+ factory-fout = <156250000>;
+ clock-frequency = <148500000>;
+ };
+ };
+ i2c@4 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <4>;
+ si5328: clock-generator@69 { /* SI5328 - u48 */
+ reg = <0x69>;
+ };
+ };
+ i2c@5 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <5>;
+ sc18is603@2f { /* sc18is602 - u93 */
+ compatible = "nxp,sc18is603";
+ reg = <0x2f>;
+ /* 4 gpios for CS not handled by driver */
+ /*
+ * USB2ANY cable or
+ * LMK04208 - u90 or
+ * LMX2594 - u102 or
+ * LMX2594 - u103 or
+ * LMX2594 - u104
+ */
+ };
+ };
+ i2c@6 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <6>;
+ /* FMC connector */
+ };
+ /* 7 NC */
+ };
+
+ i2c-mux@75 {
+ compatible = "nxp,pca9548"; /* u27 */
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x75>;
+
+ i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ /* FMCP_HSPC_IIC */
+ };
+ i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ /* NC */
+ };
+ i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ /* SYSMON */
+ };
+ i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ /* DDR4 SODIMM */
+ };
+ i2c@4 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <4>;
+ /* SFP3 */
+ };
+ i2c@5 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <5>;
+ /* SFP2 */
+ };
+ i2c@6 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <6>;
+ /* SFP1 */
+ };
+ i2c@7 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <7>;
+ /* SFP0 */
+ };
+ };
+};
+
+&rtc {
+ status = "okay";
+};
+
+&sata {
+ status = "okay";
+ /* SATA OOB timing settings */
+ ceva,p0-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
+ ceva,p0-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
+ ceva,p0-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
+ ceva,p0-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
+ ceva,p1-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
+ ceva,p1-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
+ ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
+ ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
+};
+
+/* SD1 with level shifter */
+&sdhci1 {
+ status = "okay";
+ no-1-8-v;
+};
+
+&uart0 {
+ status = "okay";
+};
+
+/* ULPI SMSC USB3320 */
+&usb0 {
+ status = "okay";
+};
--
1.9.1
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH v3 7/8] arm64: zynqmp: Add support for Xilinx zc12XX boards
2018-03-02 19:04 [PATCH v3 0/8] arm64: zynqmp: Add support for existing Xilinx ZynqMP based boards Michal Simek
` (5 preceding siblings ...)
2018-03-02 19:04 ` [PATCH v3 6/8] arm64: zynqmp: Add support for Xilinx zcu111-revA Michal Simek
@ 2018-03-02 19:04 ` Michal Simek
2018-03-02 19:04 ` [PATCH v3 8/8] arm64: zynqmp: Add support for Xilinx zc1751 Michal Simek
7 siblings, 0 replies; 12+ messages in thread
From: Michal Simek @ 2018-03-02 19:04 UTC (permalink / raw)
To: devicetree
Cc: monstr, Masahiro Yamada, linux-kernel, Arnd Bergmann,
Will Deacon, Catalin Marinas, Rob Herring, Mark Rutland,
linux-arm-kernel
These 3 boards requires minimal support to get Linux up and running.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
Changes in v3: None
Changes in v2:
- Record compatible string to xilinx.txt
Documentation/devicetree/bindings/arm/xilinx.txt | 9 ++++
arch/arm64/boot/dts/xilinx/Makefile | 3 ++
arch/arm64/boot/dts/xilinx/zynqmp-zc1232-revA.dts | 54 +++++++++++++++++++++++
arch/arm64/boot/dts/xilinx/zynqmp-zc1254-revA.dts | 42 ++++++++++++++++++
arch/arm64/boot/dts/xilinx/zynqmp-zc1275-revA.dts | 42 ++++++++++++++++++
5 files changed, 150 insertions(+)
create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-zc1232-revA.dts
create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-zc1254-revA.dts
create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-zc1275-revA.dts
diff --git a/Documentation/devicetree/bindings/arm/xilinx.txt b/Documentation/devicetree/bindings/arm/xilinx.txt
index c2bc75774010..aceccf2bf43b 100644
--- a/Documentation/devicetree/bindings/arm/xilinx.txt
+++ b/Documentation/devicetree/bindings/arm/xilinx.txt
@@ -19,6 +19,15 @@ Required root node properties:
Additional compatible strings:
+- Xilinx internal board zc1232
+ "xlnx,zynqmp-zc1232-revA", "xlnx,zynqmp-zc1232"
+
+- Xilinx internal board zc1254
+ "xlnx,zynqmp-zc1254-revA", "xlnx,zynqmp-zc1254"
+
+- Xilinx internal board zc1275
+ "xlnx,zynqmp-zc1275-revA", "xlnx,zynqmp-zc1275"
+
- Xilinx 96boards compatible board zcu100
"xlnx,zynqmp-zcu100-revC", "xlnx,zynqmp-zcu100"
diff --git a/arch/arm64/boot/dts/xilinx/Makefile b/arch/arm64/boot/dts/xilinx/Makefile
index d15c9dc1d8f2..bdda451afaad 100644
--- a/arch/arm64/boot/dts/xilinx/Makefile
+++ b/arch/arm64/boot/dts/xilinx/Makefile
@@ -1,5 +1,8 @@
# SPDX-License-Identifier: GPL-2.0
dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-ep108.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zc1232-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zc1254-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zc1275-revA.dtb
dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu100-revC.dtb
dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu102-revA.dtb
dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu102-revB.dtb
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zc1232-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zc1232-revA.dts
new file mode 100644
index 000000000000..0f7b4cf6078e
--- /dev/null
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zc1232-revA.dts
@@ -0,0 +1,54 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * dts file for Xilinx ZynqMP ZC1232
+ *
+ * (C) Copyright 2017 - 2018, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+/dts-v1/;
+
+#include "zynqmp.dtsi"
+#include "zynqmp-clk.dtsi"
+
+/ {
+ model = "ZynqMP ZC1232 RevA";
+ compatible = "xlnx,zynqmp-zc1232-revA", "xlnx,zynqmp-zc1232", "xlnx,zynqmp";
+
+ aliases {
+ serial0 = &uart0;
+ serial1 = &dcc;
+ };
+
+ chosen {
+ bootargs = "earlycon";
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x80000000>;
+ };
+};
+
+&dcc {
+ status = "okay";
+};
+
+&sata {
+ status = "okay";
+ /* SATA OOB timing settings */
+ ceva,p0-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
+ ceva,p0-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
+ ceva,p0-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
+ ceva,p0-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
+ ceva,p1-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
+ ceva,p1-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
+ ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
+ ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
+};
+
+&uart0 {
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zc1254-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zc1254-revA.dts
new file mode 100644
index 000000000000..9092828f92ec
--- /dev/null
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zc1254-revA.dts
@@ -0,0 +1,42 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * dts file for Xilinx ZynqMP ZC1254
+ *
+ * (C) Copyright 2015 - 2018, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ * Siva Durga Prasad Paladugu <sivadur@xilinx.com>
+ */
+
+/dts-v1/;
+
+#include "zynqmp.dtsi"
+#include "zynqmp-clk.dtsi"
+
+/ {
+ model = "ZynqMP ZC1254 RevA";
+ compatible = "xlnx,zynqmp-zc1254-revA", "xlnx,zynqmp-zc1254", "xlnx,zynqmp";
+
+ aliases {
+ serial0 = &uart0;
+ serial1 = &dcc;
+ };
+
+ chosen {
+ bootargs = "earlycon";
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x80000000>;
+ };
+};
+
+&dcc {
+ status = "okay";
+};
+
+&uart0 {
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zc1275-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zc1275-revA.dts
new file mode 100644
index 000000000000..4f404c580eec
--- /dev/null
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zc1275-revA.dts
@@ -0,0 +1,42 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * dts file for Xilinx ZynqMP ZC1275
+ *
+ * (C) Copyright 2017 - 2018, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ * Siva Durga Prasad Paladugu <sivadur@xilinx.com>
+ */
+
+/dts-v1/;
+
+#include "zynqmp.dtsi"
+#include "zynqmp-clk.dtsi"
+
+/ {
+ model = "ZynqMP ZC1275 RevA";
+ compatible = "xlnx,zynqmp-zc1275-revA", "xlnx,zynqmp-zc1275", "xlnx,zynqmp";
+
+ aliases {
+ serial0 = &uart0;
+ serial1 = &dcc;
+ };
+
+ chosen {
+ bootargs = "earlycon";
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x80000000>;
+ };
+};
+
+&dcc {
+ status = "okay";
+};
+
+&uart0 {
+ status = "okay";
+};
--
1.9.1
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH v3 8/8] arm64: zynqmp: Add support for Xilinx zc1751
2018-03-02 19:04 [PATCH v3 0/8] arm64: zynqmp: Add support for existing Xilinx ZynqMP based boards Michal Simek
` (6 preceding siblings ...)
2018-03-02 19:04 ` [PATCH v3 7/8] arm64: zynqmp: Add support for Xilinx zc12XX boards Michal Simek
@ 2018-03-02 19:04 ` Michal Simek
2018-03-07 20:33 ` Rob Herring
7 siblings, 1 reply; 12+ messages in thread
From: Michal Simek @ 2018-03-02 19:04 UTC (permalink / raw)
To: devicetree
Cc: monstr, Masahiro Yamada, linux-kernel, Arnd Bergmann,
Will Deacon, Catalin Marinas, Rob Herring, Mark Rutland,
linux-arm-kernel
Xilinx zc1751 boards is used for silicon validation. Board can be
extended with 5 FMCs/DCs cards to connect various IPs. Describe all
these combinations.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
---
Changes in v3:
- Remove aliases for can, usb, gpio
- dc2 fix spi_flashes and partitions
Changes in v2:
- Record compatible string to xilinx.txt
Documentation/devicetree/bindings/arm/xilinx.txt | 3 +
arch/arm64/boot/dts/xilinx/Makefile | 5 +
.../boot/dts/xilinx/zynqmp-zc1751-xm015-dc1.dts | 131 +++++++++++++++
.../boot/dts/xilinx/zynqmp-zc1751-xm016-dc2.dts | 168 +++++++++++++++++++
.../boot/dts/xilinx/zynqmp-zc1751-xm017-dc3.dts | 150 +++++++++++++++++
.../boot/dts/xilinx/zynqmp-zc1751-xm018-dc4.dts | 178 +++++++++++++++++++++
.../boot/dts/xilinx/zynqmp-zc1751-xm019-dc5.dts | 125 +++++++++++++++
7 files changed, 760 insertions(+)
create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm015-dc1.dts
create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm016-dc2.dts
create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm017-dc3.dts
create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm018-dc4.dts
create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm019-dc5.dts
diff --git a/Documentation/devicetree/bindings/arm/xilinx.txt b/Documentation/devicetree/bindings/arm/xilinx.txt
index aceccf2bf43b..0cf6fb61631d 100644
--- a/Documentation/devicetree/bindings/arm/xilinx.txt
+++ b/Documentation/devicetree/bindings/arm/xilinx.txt
@@ -28,6 +28,9 @@ Additional compatible strings:
- Xilinx internal board zc1275
"xlnx,zynqmp-zc1275-revA", "xlnx,zynqmp-zc1275"
+- Xilinx internal board zc1751
+ "xlnx,zynqmp-zc1751"
+
- Xilinx 96boards compatible board zcu100
"xlnx,zynqmp-zcu100-revC", "xlnx,zynqmp-zcu100"
diff --git a/arch/arm64/boot/dts/xilinx/Makefile b/arch/arm64/boot/dts/xilinx/Makefile
index bdda451afaad..c2a0c00272e2 100644
--- a/arch/arm64/boot/dts/xilinx/Makefile
+++ b/arch/arm64/boot/dts/xilinx/Makefile
@@ -3,6 +3,11 @@ dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-ep108.dtb
dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zc1232-revA.dtb
dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zc1254-revA.dtb
dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zc1275-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zc1751-xm015-dc1.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zc1751-xm016-dc2.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zc1751-xm017-dc3.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zc1751-xm018-dc4.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zc1751-xm019-dc5.dtb
dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu100-revC.dtb
dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu102-revA.dtb
dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu102-revB.dtb
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm015-dc1.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm015-dc1.dts
new file mode 100644
index 000000000000..9a3e39d1294f
--- /dev/null
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm015-dc1.dts
@@ -0,0 +1,131 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * dts file for Xilinx ZynqMP zc1751-xm015-dc1
+ *
+ * (C) Copyright 2015 - 2018, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+/dts-v1/;
+
+#include "zynqmp.dtsi"
+#include "zynqmp-clk.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "ZynqMP zc1751-xm015-dc1 RevA";
+ compatible = "xlnx,zynqmp-zc1751", "xlnx,zynqmp";
+
+ aliases {
+ ethernet0 = &gem3;
+ i2c0 = &i2c1;
+ mmc0 = &sdhci0;
+ mmc1 = &sdhci1;
+ rtc0 = &rtc;
+ serial0 = &uart0;
+ };
+
+ chosen {
+ bootargs = "earlycon";
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x80000000>, <0x8 0x00000000 0x0 0x80000000>;
+ };
+};
+
+&fpd_dma_chan1 {
+ status = "okay";
+};
+
+&fpd_dma_chan2 {
+ status = "okay";
+};
+
+&fpd_dma_chan3 {
+ status = "okay";
+};
+
+&fpd_dma_chan4 {
+ status = "okay";
+};
+
+&fpd_dma_chan5 {
+ status = "okay";
+};
+
+&fpd_dma_chan6 {
+ status = "okay";
+};
+
+&fpd_dma_chan7 {
+ status = "okay";
+};
+
+&fpd_dma_chan8 {
+ status = "okay";
+};
+
+&gem3 {
+ status = "okay";
+ phy-handle = <&phy0>;
+ phy-mode = "rgmii-id";
+ phy0: phy@0 {
+ reg = <0>;
+ };
+};
+
+&gpio {
+ status = "okay";
+};
+
+
+&i2c1 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ eeprom: eeprom@55 {
+ compatible = "atmel,24c64"; /* 24AA64 */
+ reg = <0x55>;
+ };
+};
+
+&rtc {
+ status = "okay";
+};
+
+&sata {
+ status = "okay";
+ /* SATA phy OOB timing settings */
+ ceva,p0-cominit-params = /bits/ 8 <0x1B 0x4D 0x18 0x28>;
+ ceva,p0-comwake-params = /bits/ 8 <0x06 0x19 0x08 0x0E>;
+ ceva,p0-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
+ ceva,p0-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
+ ceva,p1-cominit-params = /bits/ 8 <0x1B 0x4D 0x18 0x28>;
+ ceva,p1-comwake-params = /bits/ 8 <0x06 0x19 0x08 0x0E>;
+ ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
+ ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
+};
+
+/* eMMC */
+&sdhci0 {
+ status = "okay";
+ bus-width = <8>;
+};
+
+/* SD1 with level shifter */
+&sdhci1 {
+ status = "okay";
+};
+
+&uart0 {
+ status = "okay";
+};
+
+/* ULPI SMSC USB3320 */
+&usb0 {
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm016-dc2.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm016-dc2.dts
new file mode 100644
index 000000000000..11cc67184fa9
--- /dev/null
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm016-dc2.dts
@@ -0,0 +1,168 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * dts file for Xilinx ZynqMP zc1751-xm016-dc2
+ *
+ * (C) Copyright 2015 - 2018, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+/dts-v1/;
+
+#include "zynqmp.dtsi"
+#include "zynqmp-clk.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "ZynqMP zc1751-xm016-dc2 RevA";
+ compatible = "xlnx,zynqmp-zc1751", "xlnx,zynqmp";
+
+ aliases {
+ can0 = &can0;
+ can1 = &can1;
+ ethernet0 = &gem2;
+ i2c0 = &i2c0;
+ rtc0 = &rtc;
+ serial0 = &uart0;
+ serial1 = &uart1;
+ spi0 = &spi0;
+ spi1 = &spi1;
+ };
+
+ chosen {
+ bootargs = "earlycon";
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x80000000>, <0x8 0x00000000 0x0 0x80000000>;
+ };
+};
+
+&can0 {
+ status = "okay";
+};
+
+&can1 {
+ status = "okay";
+};
+
+&fpd_dma_chan1 {
+ status = "okay";
+};
+
+&fpd_dma_chan2 {
+ status = "okay";
+};
+
+&fpd_dma_chan3 {
+ status = "okay";
+};
+
+&fpd_dma_chan4 {
+ status = "okay";
+};
+
+&fpd_dma_chan5 {
+ status = "okay";
+};
+
+&fpd_dma_chan6 {
+ status = "okay";
+};
+
+&fpd_dma_chan7 {
+ status = "okay";
+};
+
+&fpd_dma_chan8 {
+ status = "okay";
+};
+
+&gem2 {
+ status = "okay";
+ phy-handle = <&phy0>;
+ phy-mode = "rgmii-id";
+ phy0: phy@5 {
+ reg = <5>;
+ ti,rx-internal-delay = <0x8>;
+ ti,tx-internal-delay = <0xa>;
+ ti,fifo-depth = <0x1>;
+ };
+};
+
+&gpio {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ tca6416_u26: gpio@20 {
+ compatible = "ti,tca6416";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ /* IRQ not connected */
+ };
+
+ rtc@68 {
+ compatible = "dallas,ds1339";
+ reg = <0x68>;
+ };
+};
+
+&rtc {
+ status = "okay";
+};
+
+&spi0 {
+ status = "okay";
+ num-cs = <1>;
+
+ spi0_flash0: flash0@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "sst,sst25wf080", "jedec,spi-nor";
+ spi-max-frequency = <50000000>;
+ reg = <0>;
+
+ partition@0 {
+ label = "data";
+ reg = <0x0 0x100000>;
+ };
+ };
+};
+
+&spi1 {
+ status = "okay";
+ num-cs = <1>;
+
+ spi1_flash0: flash0@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "atmel,at45db041e", "atmel,at45", "atmel,dataflash";
+ spi-max-frequency = <20000000>;
+ reg = <0>;
+
+ partition@0 {
+ label = "data";
+ reg = <0x0 0x84000>;
+ };
+ };
+};
+
+/* ULPI SMSC USB3320 */
+&usb1 {
+ status = "okay";
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&uart1 {
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm017-dc3.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm017-dc3.dts
new file mode 100644
index 000000000000..7a49deeae647
--- /dev/null
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm017-dc3.dts
@@ -0,0 +1,150 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * dts file for Xilinx ZynqMP zc1751-xm017-dc3
+ *
+ * (C) Copyright 2016 - 2018, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+/dts-v1/;
+
+#include "zynqmp.dtsi"
+#include "zynqmp-clk.dtsi"
+
+/ {
+ model = "ZynqMP zc1751-xm017-dc3 RevA";
+ compatible = "xlnx,zynqmp-zc1751", "xlnx,zynqmp";
+
+ aliases {
+ ethernet0 = &gem0;
+ i2c0 = &i2c0;
+ i2c1 = &i2c1;
+ mmc0 = &sdhci1;
+ rtc0 = &rtc;
+ serial0 = &uart0;
+ serial1 = &uart1;
+ };
+
+ chosen {
+ bootargs = "earlycon";
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x80000000>, <0x8 0x00000000 0x0 0x80000000>;
+ };
+};
+
+&fpd_dma_chan1 {
+ status = "okay";
+};
+
+&fpd_dma_chan2 {
+ status = "okay";
+};
+
+&fpd_dma_chan3 {
+ status = "okay";
+};
+
+&fpd_dma_chan4 {
+ status = "okay";
+};
+
+&fpd_dma_chan5 {
+ status = "okay";
+};
+
+&fpd_dma_chan6 {
+ status = "okay";
+};
+
+&fpd_dma_chan7 {
+ status = "okay";
+};
+
+&fpd_dma_chan8 {
+ status = "okay";
+};
+
+&gem0 {
+ status = "okay";
+ phy-handle = <&phy0>;
+ phy-mode = "rgmii-id";
+ phy0: phy@0 { /* VSC8211 */
+ reg = <0>;
+ };
+};
+
+&gpio {
+ status = "okay";
+};
+
+/* just eeprom here */
+&i2c0 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ tca6416_u26: gpio@20 {
+ compatible = "ti,tca6416";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ /* IRQ not connected */
+ };
+
+ rtc@68 {
+ compatible = "dallas,ds1339";
+ reg = <0x68>;
+ };
+};
+
+/* eeprom24c02 and SE98A temp chip pca9306 */
+&i2c1 {
+ status = "okay";
+ clock-frequency = <400000>;
+};
+
+&rtc {
+ status = "okay";
+};
+
+&sata {
+ status = "okay";
+ /* SATA phy OOB timing settings */
+ ceva,p0-cominit-params = /bits/ 8 <0x1B 0x4D 0x18 0x28>;
+ ceva,p0-comwake-params = /bits/ 8 <0x06 0x19 0x08 0x0E>;
+ ceva,p0-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
+ ceva,p0-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
+ ceva,p1-cominit-params = /bits/ 8 <0x1B 0x4D 0x18 0x28>;
+ ceva,p1-comwake-params = /bits/ 8 <0x06 0x19 0x08 0x0E>;
+ ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
+ ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
+};
+
+&sdhci1 { /* emmc with some settings */
+ status = "okay";
+};
+
+/* main */
+&uart0 {
+ status = "okay";
+};
+
+/* DB9 */
+&uart1 {
+ status = "okay";
+};
+
+&usb0 {
+ status = "okay";
+ dr_mode = "host";
+};
+
+/* ULPI SMSC USB3320 */
+&usb1 {
+ status = "okay";
+ dr_mode = "host";
+};
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm018-dc4.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm018-dc4.dts
new file mode 100644
index 000000000000..54c7b4f1d1e4
--- /dev/null
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm018-dc4.dts
@@ -0,0 +1,178 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * dts file for Xilinx ZynqMP zc1751-xm018-dc4
+ *
+ * (C) Copyright 2015 - 2018, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+/dts-v1/;
+
+#include "zynqmp.dtsi"
+#include "zynqmp-clk.dtsi"
+
+/ {
+ model = "ZynqMP zc1751-xm018-dc4";
+ compatible = "xlnx,zynqmp-zc1751", "xlnx,zynqmp";
+
+ aliases {
+ ethernet0 = &gem0;
+ ethernet1 = &gem1;
+ ethernet2 = &gem2;
+ ethernet3 = &gem3;
+ i2c0 = &i2c0;
+ i2c1 = &i2c1;
+ rtc0 = &rtc;
+ serial0 = &uart0;
+ serial1 = &uart1;
+ };
+
+ chosen {
+ bootargs = "earlycon";
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x80000000>, <0x8 0x00000000 0x0 0x80000000>;
+ };
+};
+
+&can0 {
+ status = "okay";
+};
+
+&can1 {
+ status = "okay";
+};
+
+&fpd_dma_chan1 {
+ status = "okay";
+};
+
+&fpd_dma_chan2 {
+ status = "okay";
+};
+
+&fpd_dma_chan3 {
+ status = "okay";
+};
+
+&fpd_dma_chan4 {
+ status = "okay";
+};
+
+&fpd_dma_chan5 {
+ status = "okay";
+};
+
+&fpd_dma_chan6 {
+ status = "okay";
+};
+
+&fpd_dma_chan7 {
+ status = "okay";
+};
+
+&fpd_dma_chan8 {
+ status = "okay";
+};
+
+&lpd_dma_chan1 {
+ status = "okay";
+};
+
+&lpd_dma_chan2 {
+ status = "okay";
+};
+
+&lpd_dma_chan3 {
+ status = "okay";
+};
+
+&lpd_dma_chan4 {
+ status = "okay";
+};
+
+&lpd_dma_chan5 {
+ status = "okay";
+};
+
+&lpd_dma_chan6 {
+ status = "okay";
+};
+
+&lpd_dma_chan7 {
+ status = "okay";
+};
+
+&lpd_dma_chan8 {
+ status = "okay";
+};
+
+&gem0 {
+ status = "okay";
+ phy-mode = "rgmii-id";
+ phy-handle = <ðernet_phy0>;
+ ethernet_phy0: ethernet-phy@0 { /* Marvell 88e1512 */
+ reg = <0>;
+ };
+ ethernet_phy7: ethernet-phy@7 { /* Vitesse VSC8211 */
+ reg = <7>;
+ };
+ ethernet_phy3: ethernet-phy@3 { /* Realtek RTL8211DN */
+ reg = <3>;
+ };
+ ethernet_phy8: ethernet-phy@8 { /* Vitesse VSC8211 */
+ reg = <8>;
+ };
+};
+
+&gem1 {
+ status = "okay";
+ phy-mode = "rgmii-id";
+ phy-handle = <ðernet_phy7>;
+};
+
+&gem2 {
+ status = "okay";
+ phy-mode = "rgmii-id";
+ phy-handle = <ðernet_phy3>;
+};
+
+&gem3 {
+ status = "okay";
+ phy-mode = "rgmii-id";
+ phy-handle = <ðernet_phy8>;
+};
+
+&gpio {
+ status = "okay";
+};
+
+&i2c0 {
+ clock-frequency = <400000>;
+ status = "okay";
+};
+
+&i2c1 {
+ clock-frequency = <400000>;
+ status = "okay";
+};
+
+&rtc {
+ status = "okay";
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&uart1 {
+ status = "okay";
+};
+
+&watchdog0 {
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm019-dc5.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm019-dc5.dts
new file mode 100644
index 000000000000..b8b5ff13818d
--- /dev/null
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm019-dc5.dts
@@ -0,0 +1,125 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * dts file for Xilinx ZynqMP zc1751-xm019-dc5
+ *
+ * (C) Copyright 2015 - 2018, Xilinx, Inc.
+ *
+ * Siva Durga Prasad <siva.durga.paladugu@xilinx.com>
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+/dts-v1/;
+
+#include "zynqmp.dtsi"
+#include "zynqmp-clk.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "ZynqMP zc1751-xm019-dc5 RevA";
+ compatible = "xlnx,zynqmp-zc1751", "xlnx,zynqmp";
+
+ aliases {
+ ethernet0 = &gem1;
+ i2c0 = &i2c0;
+ i2c1 = &i2c1;
+ mmc0 = &sdhci0;
+ serial0 = &uart0;
+ serial1 = &uart1;
+ };
+
+ chosen {
+ bootargs = "earlycon";
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x80000000>, <0x8 0x00000000 0x0 0x80000000>;
+ };
+};
+
+&fpd_dma_chan1 {
+ status = "okay";
+};
+
+&fpd_dma_chan2 {
+ status = "okay";
+};
+
+&fpd_dma_chan3 {
+ status = "okay";
+};
+
+&fpd_dma_chan4 {
+ status = "okay";
+};
+
+&fpd_dma_chan5 {
+ status = "okay";
+};
+
+&fpd_dma_chan6 {
+ status = "okay";
+};
+
+&fpd_dma_chan7 {
+ status = "okay";
+};
+
+&fpd_dma_chan8 {
+ status = "okay";
+};
+
+&gem1 {
+ status = "okay";
+ phy-handle = <&phy0>;
+ phy-mode = "rgmii-id";
+ phy0: phy@0 {
+ reg = <0>;
+ };
+};
+
+&gpio {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+};
+
+&i2c1 {
+ status = "okay";
+};
+
+&sdhci0 {
+ status = "okay";
+ no-1-8-v;
+};
+
+&ttc0 {
+ status = "okay";
+};
+
+&ttc1 {
+ status = "okay";
+};
+
+&ttc2 {
+ status = "okay";
+};
+
+&ttc3 {
+ status = "okay";
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&uart1 {
+ status = "okay";
+};
+
+&watchdog0 {
+ status = "okay";
+};
--
1.9.1
^ permalink raw reply related [flat|nested] 12+ messages in thread
* Re: [PATCH v3 4/8] arm64: zynqmp: Add support for Xilinx zcu104-revA
2018-03-02 19:04 ` [PATCH v3 4/8] arm64: zynqmp: Add support for Xilinx zcu104-revA Michal Simek
@ 2018-03-07 20:31 ` Rob Herring
0 siblings, 0 replies; 12+ messages in thread
From: Rob Herring @ 2018-03-07 20:31 UTC (permalink / raw)
To: Michal Simek
Cc: devicetree, monstr, Masahiro Yamada, linux-kernel, Arnd Bergmann,
Will Deacon, Catalin Marinas, Mark Rutland, linux-arm-kernel
On Fri, Mar 02, 2018 at 08:04:30PM +0100, Michal Simek wrote:
> Xilinx zcu104 is another customer board. It is sort of zcu102 clone
> with some differences.
>
> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
> ---
>
> Changes in v3:
> - Use i2c-mux instead of i2cswitch - was done with zcu106
> - Remove gpio and usb aliases
>
> Changes in v2:
> - Remove i2c mw u-boot commands
> - Record compatible string to xilinx.txt
>
> Documentation/devicetree/bindings/arm/xilinx.txt | 3 +
> arch/arm64/boot/dts/xilinx/Makefile | 1 +
> arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts | 195 ++++++++++++++++++++++
> 3 files changed, 199 insertions(+)
> create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts
Reviewed-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH v3 5/8] arm64: zynqmp: Add support for Xilinx zcu106-revA
2018-03-02 19:04 ` [PATCH v3 5/8] arm64: zynqmp: Add support for Xilinx zcu106-revA Michal Simek
@ 2018-03-07 20:32 ` Rob Herring
0 siblings, 0 replies; 12+ messages in thread
From: Rob Herring @ 2018-03-07 20:32 UTC (permalink / raw)
To: Michal Simek
Cc: devicetree, monstr, Masahiro Yamada, linux-kernel, Arnd Bergmann,
Will Deacon, Catalin Marinas, Mark Rutland, linux-arm-kernel
On Fri, Mar 02, 2018 at 08:04:31PM +0100, Michal Simek wrote:
> Xilinx zcu106 is a customer board. It is reusing some parts from zcu102.
>
> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
> ---
>
> Changes in v3:
> - remove gpio and usb aliases
>
> Changes in v2:
> - Remove i2c mw u-boot commands
> - Use i2c-mux instead of i2cswitch
> - Use clock generator without numbers
> - Record compatible string to xilinx.txt
>
> Documentation/devicetree/bindings/arm/xilinx.txt | 3 +
> arch/arm64/boot/dts/xilinx/Makefile | 1 +
> arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts | 522 ++++++++++++++++++++++
> 3 files changed, 526 insertions(+)
> create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts
Reviewed-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH v3 8/8] arm64: zynqmp: Add support for Xilinx zc1751
2018-03-02 19:04 ` [PATCH v3 8/8] arm64: zynqmp: Add support for Xilinx zc1751 Michal Simek
@ 2018-03-07 20:33 ` Rob Herring
0 siblings, 0 replies; 12+ messages in thread
From: Rob Herring @ 2018-03-07 20:33 UTC (permalink / raw)
To: Michal Simek
Cc: devicetree, monstr, Masahiro Yamada, linux-kernel, Arnd Bergmann,
Will Deacon, Catalin Marinas, Mark Rutland, linux-arm-kernel
On Fri, Mar 02, 2018 at 08:04:34PM +0100, Michal Simek wrote:
> Xilinx zc1751 boards is used for silicon validation. Board can be
> extended with 5 FMCs/DCs cards to connect various IPs. Describe all
> these combinations.
>
> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
> ---
>
> Changes in v3:
> - Remove aliases for can, usb, gpio
> - dc2 fix spi_flashes and partitions
>
> Changes in v2:
> - Record compatible string to xilinx.txt
>
> Documentation/devicetree/bindings/arm/xilinx.txt | 3 +
> arch/arm64/boot/dts/xilinx/Makefile | 5 +
> .../boot/dts/xilinx/zynqmp-zc1751-xm015-dc1.dts | 131 +++++++++++++++
> .../boot/dts/xilinx/zynqmp-zc1751-xm016-dc2.dts | 168 +++++++++++++++++++
> .../boot/dts/xilinx/zynqmp-zc1751-xm017-dc3.dts | 150 +++++++++++++++++
> .../boot/dts/xilinx/zynqmp-zc1751-xm018-dc4.dts | 178 +++++++++++++++++++++
> .../boot/dts/xilinx/zynqmp-zc1751-xm019-dc5.dts | 125 +++++++++++++++
> 7 files changed, 760 insertions(+)
> create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm015-dc1.dts
> create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm016-dc2.dts
> create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm017-dc3.dts
> create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm018-dc4.dts
> create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm019-dc5.dts
Reviewed-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 12+ messages in thread
end of thread, other threads:[~2018-03-07 20:33 UTC | newest]
Thread overview: 12+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2018-03-02 19:04 [PATCH v3 0/8] arm64: zynqmp: Add support for existing Xilinx ZynqMP based boards Michal Simek
2018-03-02 19:04 ` [PATCH v3 1/8] dt-bindings: xilinx: Add description for ZynqMP Michal Simek
2018-03-02 19:04 ` [PATCH v3 2/8] arm64: zynqmp: Add support for Xilinx zcu100-revC Michal Simek
2018-03-02 19:04 ` [PATCH v3 3/8] arm64: zynqmp: Add support for Xilinx zcu102 Michal Simek
2018-03-02 19:04 ` [PATCH v3 4/8] arm64: zynqmp: Add support for Xilinx zcu104-revA Michal Simek
2018-03-07 20:31 ` Rob Herring
2018-03-02 19:04 ` [PATCH v3 5/8] arm64: zynqmp: Add support for Xilinx zcu106-revA Michal Simek
2018-03-07 20:32 ` Rob Herring
2018-03-02 19:04 ` [PATCH v3 6/8] arm64: zynqmp: Add support for Xilinx zcu111-revA Michal Simek
2018-03-02 19:04 ` [PATCH v3 7/8] arm64: zynqmp: Add support for Xilinx zc12XX boards Michal Simek
2018-03-02 19:04 ` [PATCH v3 8/8] arm64: zynqmp: Add support for Xilinx zc1751 Michal Simek
2018-03-07 20:33 ` Rob Herring
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).