From: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
To: "Rob Herring" <robh+dt@kernel.org>,
"Andreas Färber" <afaerber@suse.de>,
"Manivannan Sadhasivam" <manivannan.sadhasivam@linaro.org>
Cc: devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org, linux-actions@lists.infradead.org
Subject: [PATCH 00/10] Add CMU/RMU/DMA/MMC/I2C support for Actions Semi S500 SoCs
Date: Fri, 26 Jun 2020 02:34:12 +0300 [thread overview]
Message-ID: <cover.1593124368.git.cristian.ciocaltea@gmail.com> (raw)
This patchset brings a series of improvements for the Actions Semi S500
SoCs family, by adding support for Clock & Reset Management Units, DMA,
MMC & I2C controllers.
Please note the patches contain only DTS changes, but most of them
depend on previous work which is currently under review:
- Add RMU and DMAC/GPIO clock support for Actions Semi S500 SoCs
https://lore.kernel.org/lkml/cover.1592941257.git.cristian.ciocaltea@gmail.com/
- Add Actions Semi S500 pinctrl support
https://lore.kernel.org/lkml/cover.1593112402.git.cristian.ciocaltea@gmail.com/
For the moment, I have only enabled the features tested on RoseapplePi,
the SBC for which an initial support has been already submitted via:
https://lore.kernel.org/lkml/cover.1592123160.git.cristian.ciocaltea@gmail.com/
Thanks,
Cristi
Cristian Ciocaltea (10):
arm: dts: owl-s500: Add Clock Management Unit
arm: dts: owl-s500: Set UART clock refs from CMU
arm: dts: owl-s500: Add DMA controller
arm: dts: owl-s500: Add Reset Controller support
arm: dts: owl-s500: Add pinctrl node
arm: dts: owl-s500: Add MMC nodes
arm: dts: owl-s500: Add I2C nodes
arm: dts: owl-s500-roseapplepi: Use UART clock from CMU
arm: dts: owl-s500-roseapplepi: Add uSD support
arm: dts: owl-s500-roseapplepi: Enable I2C0
arch/arm/boot/dts/owl-s500-roseapplepi.dts | 96 ++++++++++++++-
arch/arm/boot/dts/owl-s500.dtsi | 130 +++++++++++++++++++++
2 files changed, 221 insertions(+), 5 deletions(-)
--
2.27.0
next reply other threads:[~2020-06-25 23:34 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-06-25 23:34 Cristian Ciocaltea [this message]
2020-06-25 23:34 ` [PATCH 01/10] arm: dts: owl-s500: Add Clock Management Unit Cristian Ciocaltea
2020-06-25 23:34 ` [PATCH 02/10] arm: dts: owl-s500: Set UART clock refs from CMU Cristian Ciocaltea
2020-06-25 23:34 ` [PATCH 03/10] arm: dts: owl-s500: Add DMA controller Cristian Ciocaltea
2020-06-25 23:34 ` [PATCH 04/10] arm: dts: owl-s500: Add Reset Controller support Cristian Ciocaltea
2020-06-25 23:34 ` [PATCH 05/10] arm: dts: owl-s500: Add pinctrl node Cristian Ciocaltea
2020-06-25 23:34 ` [PATCH 06/10] arm: dts: owl-s500: Add MMC nodes Cristian Ciocaltea
2020-06-25 23:34 ` [PATCH 07/10] arm: dts: owl-s500: Add I2C nodes Cristian Ciocaltea
2020-06-25 23:34 ` [PATCH 08/10] arm: dts: owl-s500-roseapplepi: Use UART clock from CMU Cristian Ciocaltea
2020-06-25 23:34 ` [PATCH 09/10] arm: dts: owl-s500-roseapplepi: Add uSD support Cristian Ciocaltea
2020-06-25 23:34 ` [PATCH 10/10] arm: dts: owl-s500-roseapplepi: Enable I2C0 Cristian Ciocaltea
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=cover.1593124368.git.cristian.ciocaltea@gmail.com \
--to=cristian.ciocaltea@gmail.com \
--cc=afaerber@suse.de \
--cc=devicetree@vger.kernel.org \
--cc=linux-actions@lists.infradead.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=manivannan.sadhasivam@linaro.org \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).