Re: [PATCH v3 3/3] ARM: dts: stm32: add initial support for stm32mp157-odyssey board

[Ahmad Fatoum <a.fatoum@pengutronix.de>]

Hi,

On 7/23/20 9:43 PM, Marcin Słoniewski wrote:
> Hello Ahmad,
> 
> First of all thank you very much for your feedback, it was very helpful!
> 
> śr., 22 lip 2020 o 08:40 Ahmad Fatoum <a.fatoum@pengutronix.de> napisał(a):
>>
>> On 7/21/20 8:53 PM, Marcin Sloniewski wrote:
>>> Add support for Seeed Studio's stm32mp157c odyssey board.
>>> Board consists of SoM with stm32mp157c with 4GB eMMC and 512 MB DDR3 RAM
>>> and carrier board with USB and ETH interfaces, SD card connector,
>>> wifi and BT chip AP6236.
>>>
>>> In this patch only basic kernel boot is supported and interfacing
>>> SD card and on-board eMMC.
>>>
>>> Signed-off-by: Marcin Sloniewski <marcin.sloniewski@gmail.com>
>>> ---
>>>
>>> Changes in v3:
>>> - fix compilation on tip of stm32-next
>>>   due to change in names for pinctrl
>>> - fix deprecated binding for led node
>>> - fix redundant "okay" statuses
>>> - add phy part number for eth in comment
>>
>> You didn't address all my feedback on v2.
> I posted today v4 of the patch-set with further changes.
> Regarding watchdog from pmic: when using this watchdog
> my board resets even though I feed the watchdog. I'm going to
> use the internal watchdog for now and keep in mind that this
> could be improved in future.

Who turns on the watchdog? If it's in the bootloader,
you can't rely on CONFIG_WATCHDOG_HANDLE_BOOT_ENABLED feeding it till
userspace takes over because the stpmic1_wdt doesn't populate
WDOG_HW_RUNNING in status.

> I changed phy address to 7, indeed you were right about it.
> But unfortunately even though I set the address correctly phy
> is still missing according to dmesg (I checked datasheet and schematics
> the address is surely correct now).
> That's something I would like to postpone a little bit as well for now.

You sent out v4 with a phy address of 7 though.
Did you get it working meanwhile?

> 
>>
>>> Changes in v2:
>>> - add new odyssey dts to Makefile
>>>
>>>  arch/arm/boot/dts/Makefile                    |   3 +-
>>>  .../arm/boot/dts/stm32mp157c-odyssey-som.dtsi | 276 ++++++++++++++++++
>>>  arch/arm/boot/dts/stm32mp157c-odyssey.dts     |  72 +++++
>>>  3 files changed, 350 insertions(+), 1 deletion(-)
>>>  create mode 100644 arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi
>>>  create mode 100644 arch/arm/boot/dts/stm32mp157c-odyssey.dts
>>>
>>> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
>>> index e6a1cac0bfc7..a3ea2301c82c 100644
>>> --- a/arch/arm/boot/dts/Makefile
>>> +++ b/arch/arm/boot/dts/Makefile
>>> @@ -1047,7 +1047,8 @@ dtb-$(CONFIG_ARCH_STM32) += \
>>>       stm32mp157c-dk2.dtb \
>>>       stm32mp157c-ed1.dtb \
>>>       stm32mp157c-ev1.dtb \
>>> -     stm32mp157c-lxa-mc1.dtb
>>> +     stm32mp157c-lxa-mc1.dtb \
>>> +     stm32mp157c-odyssey.dtb
>>>  dtb-$(CONFIG_MACH_SUN4I) += \
>>>       sun4i-a10-a1000.dtb \
>>>       sun4i-a10-ba10-tvbox.dtb \
>>> diff --git a/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi b/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi
>>> new file mode 100644
>>> index 000000000000..935632caddd6
>>> --- /dev/null
>>> +++ b/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi
>>> @@ -0,0 +1,276 @@
>>> +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
>>> +/*
>>> + * Copyright (C) 2020 Marcin Sloniewski <marcin.sloniewski@gmail.com>.
>>> + */
>>> +
>>> +/dts-v1/;
>>> +
>>> +#include "stm32mp157.dtsi"
>>> +#include "stm32mp15xc.dtsi"
>>> +#include "stm32mp15-pinctrl.dtsi"
>>> +#include "stm32mp15xxac-pinctrl.dtsi"
>>> +#include <dt-bindings/gpio/gpio.h>
>>> +#include <dt-bindings/leds/common.h>
>>> +#include <dt-bindings/mfd/st,stpmic1.h>
>>> +
>>> +/ {
>>> +     model = "Seeed Studio Odyssey-STM32MP157C SOM";
>>> +     compatible = "seeed,stm32mp157c-odyssey-som", "st,stm32mp157";
>>> +
>>> +     memory@c0000000 {
>>> +             device_type = "memory";
>>> +             reg = <0xc0000000 0x20000000>;
>>> +     };
>>> +
>>> +     reserved-memory {
>>> +             #address-cells = <1>;
>>> +             #size-cells = <1>;
>>> +             ranges;
>>> +
>>> +             mcuram2: mcuram2@10000000 {
>>> +                     compatible = "shared-dma-pool";
>>> +                     reg = <0x10000000 0x40000>;
>>> +                     no-map;
>>> +             };
>>> +
>>> +             vdev0vring0: vdev0vring0@10040000 {
>>> +                     compatible = "shared-dma-pool";
>>> +                     reg = <0x10040000 0x1000>;
>>> +                     no-map;
>>> +             };
>>> +
>>> +             vdev0vring1: vdev0vring1@10041000 {
>>> +                     compatible = "shared-dma-pool";
>>> +                     reg = <0x10041000 0x1000>;
>>> +                     no-map;
>>> +             };
>>> +
>>> +             vdev0buffer: vdev0buffer@10042000 {
>>> +                     compatible = "shared-dma-pool";
>>> +                     reg = <0x10042000 0x4000>;
>>> +                     no-map;
>>> +             };
>>> +
>>> +             mcuram: mcuram@30000000 {
>>> +                     compatible = "shared-dma-pool";
>>> +                     reg = <0x30000000 0x40000>;
>>> +                     no-map;
>>> +             };
>>> +
>>> +             retram: retram@38000000 {
>>> +                     compatible = "shared-dma-pool";
>>> +                     reg = <0x38000000 0x10000>;
>>> +                     no-map;
>>> +             };
>>> +
>>> +             gpu_reserved: gpu@d4000000 {
>>> +                     reg = <0xd4000000 0x4000000>;
>>> +                     no-map;
>>> +             };
>>> +     };
>>> +
>>> +     led {
>>> +             compatible = "gpio-leds";
>>> +             led-blue {
>>> +                     color = <LED_COLOR_ID_BLUE>;
>>> +                     function = LED_FUNCTION_HEARTBEAT;
>>> +                     gpios = <&gpiog 3 GPIO_ACTIVE_HIGH>;
>>> +                     linux,default-trigger = "heartbeat";
>>> +             };
>>> +     };
>>> +};
>>> +
>>> +&gpu {
>>> +     contiguous-area = <&gpu_reserved>;
>>> +     status = "okay";
>>> +};
>>> +
>>> +&i2c2 {
>>> +     pinctrl-names = "default";
>>> +     pinctrl-0 = <&i2c2_pins_a>;
>>> +     i2c-scl-rising-time-ns = <185>;
>>> +     i2c-scl-falling-time-ns = <20>;
>>> +     status = "okay";
>>> +     /* spare dmas for other usage */
>>> +     /delete-property/dmas;
>>> +     /delete-property/dma-names;
>>> +
>>> +     pmic: stpmic@33 {
>>> +             compatible = "st,stpmic1";
>>> +             reg = <0x33>;
>>> +             interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
>>> +             interrupt-controller;
>>> +             #interrupt-cells = <2>;
>>> +
>>> +             regulators {
>>> +                     compatible = "st,stpmic1-regulators";
>>> +                     ldo1-supply = <&v3v3>;
>>> +                     ldo3-supply = <&vdd_ddr>;
>>> +                     ldo6-supply = <&v3v3>;
>>> +                     pwr_sw1-supply = <&bst_out>;
>>> +                     pwr_sw2-supply = <&bst_out>;
>>> +
>>> +                     vddcore: buck1 {
>>> +                             regulator-name = "vddcore";
>>> +                             regulator-min-microvolt = <800000>;
>>> +                             regulator-max-microvolt = <1350000>;
>>> +                             regulator-always-on;
>>> +                             regulator-initial-mode = <0>;
>>> +                             regulator-over-current-protection;
>>> +                     };
>>> +
>>> +                     vdd_ddr: buck2 {
>>> +                             regulator-name = "vdd_ddr";
>>> +                             regulator-min-microvolt = <1350000>;
>>> +                             regulator-max-microvolt = <1350000>;
>>> +                             regulator-always-on;
>>> +                             regulator-initial-mode = <0>;
>>> +                             regulator-over-current-protection;
>>> +                     };
>>> +
>>> +                     vdd: buck3 {
>>> +                             regulator-name = "vdd";
>>> +                             regulator-min-microvolt = <3300000>;
>>> +                             regulator-max-microvolt = <3300000>;
>>> +                             regulator-always-on;
>>> +                             st,mask-reset;
>>> +                             regulator-initial-mode = <0>;
>>> +                             regulator-over-current-protection;
>>> +                     };
>>> +
>>> +                     v3v3: buck4 {
>>> +                             regulator-name = "v3v3";
>>> +                             regulator-min-microvolt = <3300000>;
>>> +                             regulator-max-microvolt = <3300000>;
>>> +                             regulator-always-on;
>>> +                             regulator-over-current-protection;
>>> +                             regulator-initial-mode = <0>;
>>> +                     };
>>> +
>>> +                     v1v8_audio: ldo1 {
>>> +                             regulator-name = "v1v8_audio";
>>> +                             regulator-min-microvolt = <1800000>;
>>> +                             regulator-max-microvolt = <1800000>;
>>> +                             regulator-always-on;
>>> +                             interrupts = <IT_CURLIM_LDO1 0>;
>>> +                     };
>>> +
>>> +                     v3v3_hdmi: ldo2 {
>>> +                             regulator-name = "v3v3_hdmi";
>>> +                             regulator-min-microvolt = <3300000>;
>>> +                             regulator-max-microvolt = <3300000>;
>>> +                             regulator-always-on;
>>> +                             interrupts = <IT_CURLIM_LDO2 0>;
>>> +                     };
>>> +
>>> +                     vtt_ddr: ldo3 {
>>> +                             regulator-name = "vtt_ddr";
>>> +                             regulator-min-microvolt = <500000>;
>>> +                             regulator-max-microvolt = <750000>;
>>> +                             regulator-always-on;
>>> +                             regulator-over-current-protection;
>>> +                     };
>>> +
>>> +                     vdd_usb: ldo4 {
>>> +                             regulator-name = "vdd_usb";
>>> +                             regulator-min-microvolt = <3300000>;
>>> +                             regulator-max-microvolt = <3300000>;
>>> +                             interrupts = <IT_CURLIM_LDO4 0>;
>>> +                     };
>>> +
>>> +                     vdda: ldo5 {
>>> +                             regulator-name = "vdda";
>>> +                             regulator-min-microvolt = <2900000>;
>>> +                             regulator-max-microvolt = <2900000>;
>>> +                             interrupts = <IT_CURLIM_LDO5 0>;
>>> +                             regulator-boot-on;
>>> +                     };
>>> +
>>> +                     v1v2_hdmi: ldo6 {
>>> +                             regulator-name = "v1v2_hdmi";
>>> +                             regulator-min-microvolt = <1200000>;
>>> +                             regulator-max-microvolt = <1200000>;
>>> +                             regulator-always-on;
>>> +                             interrupts = <IT_CURLIM_LDO6 0>;
>>> +                     };
>>> +
>>> +                     vref_ddr: vref_ddr {
>>> +                             regulator-name = "vref_ddr";
>>> +                             regulator-always-on;
>>> +                             regulator-over-current-protection;
>>> +                     };
>>> +
>>> +                      bst_out: boost {
>>> +                             regulator-name = "bst_out";
>>> +                             interrupts = <IT_OCP_BOOST 0>;
>>> +                      };
>>> +
>>> +                     vbus_otg: pwr_sw1 {
>>> +                             regulator-name = "vbus_otg";
>>> +                             interrupts = <IT_OCP_OTG 0>;
>>> +                      };
>>> +
>>> +                      vbus_sw: pwr_sw2 {
>>> +                             regulator-name = "vbus_sw";
>>> +                             interrupts = <IT_OCP_SWOUT 0>;
>>> +                             regulator-active-discharge;
>>> +                      };
>>> +             };
>>> +
>>> +             onkey {
>>> +                     compatible = "st,stpmic1-onkey";
>>> +                     interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 0>;
>>> +                     interrupt-names = "onkey-falling", "onkey-rising";
>>> +                     power-off-time-sec = <10>;
>>> +             };
>>> +
>>> +             watchdog {
>>> +                     compatible = "st,stpmic1-wdt";
>>> +                     status = "disabled";
>>> +             };
>>> +     };
>>> +};
>>> +
>>> +&ipcc {
>>> +     status = "okay";
>>> +};
>>> +
>>> +&iwdg2 {
>>> +     timeout-sec = <32>;
>>> +     status = "okay";
>>> +};
>>> +
>>> +&m4_rproc {
>>> +     memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>,
>>> +                     <&vdev0vring1>, <&vdev0buffer>;
>>> +     mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>;
>>> +     mbox-names = "vq0", "vq1", "shutdown";
>>> +     interrupt-parent = <&exti>;
>>> +     interrupts = <68 1>;
>>> +     status = "okay";
>>> +};
>>> +
>>> +&rng1 {
>>> +     status = "okay";
>>> +};
>>> +
>>> +&rtc {
>>> +     status = "okay";
>>> +};
>>> +
>>> +&sdmmc2 {
>>> +     pinctrl-names = "default", "opendrain", "sleep";
>>> +     pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a>;
>>> +     pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_a>;
>>> +     pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_a>;
>>> +     non-removable;
>>> +     no-sd;
>>> +     no-sdio;
>>> +     st,neg-edge;
>>> +     bus-width = <4>;
>>> +     vmmc-supply = <&v3v3>;
>>> +     vqmmc-supply = <&v3v3>;
>>> +     mmc-ddr-3_3v;
>>> +     status = "okay";
>>> +};
>>> +
>>> diff --git a/arch/arm/boot/dts/stm32mp157c-odyssey.dts b/arch/arm/boot/dts/stm32mp157c-odyssey.dts
>>> new file mode 100644
>>> index 000000000000..09edf6afa155
>>> --- /dev/null
>>> +++ b/arch/arm/boot/dts/stm32mp157c-odyssey.dts
>>> @@ -0,0 +1,72 @@
>>> +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
>>> +/*
>>> + * Copyright (C) 2020 Marcin Sloniewski <marcin.sloniewski@gmail.com>.
>>> + */
>>> +
>>> +/dts-v1/;
>>> +
>>> +#include "stm32mp157c-odyssey-som.dtsi"
>>> +
>>> +/ {
>>> +     model = "Seeed Studio Odyssey-STM32MP157C Board";
>>> +     compatible = "seeed,stm32mp157c-odyssey", "st,stm32mp157";
>>> +
>>> +     aliases {
>>> +             ethernet0 = &ethernet0;
>>> +             serial0 = &uart4;
>>> +     };
>>> +
>>> +     chosen {
>>> +             stdout-path = "serial0:115200n8";
>>> +     };
>>> +};
>>> +
>>> +&ethernet0 {
>>> +     status = "okay";
>>> +     pinctrl-0 = <&ethernet0_rgmii_pins_a>;
>>> +     pinctrl-1 = <&ethernet0_rgmii_sleep_pins_a>;
>>> +     pinctrl-names = "default", "sleep";
>>> +     phy-mode = "rgmii-id";
>>> +     max-speed = <1000>;
>>> +     phy-handle = <&phy0>;
>>> +
>>> +     mdio0 {
>>> +             #address-cells = <1>;
>>> +             #size-cells = <0>;
>>> +             compatible = "snps,dwmac-mdio";
>>> +             phy0: ethernet-phy@0 { /* KSZ9031RN */
>>> +                     reg = <0>;
>>> +             };
>>> +     };
>>> +};
>>> +
>>> +&i2c1 {
>>> +     pinctrl-names = "default", "sleep";
>>> +     pinctrl-0 = <&i2c1_pins_a>;
>>> +     pinctrl-1 = <&i2c1_sleep_pins_a>;
>>> +     i2c-scl-rising-time-ns = <100>;
>>> +     i2c-scl-falling-time-ns = <7>;
>>> +     status = "okay";
>>> +     /delete-property/dmas;
>>> +     /delete-property/dma-names;
>>> +};
>>> +
>>> +&sdmmc1 {
>>> +     pinctrl-names = "default", "opendrain", "sleep";
>>> +     pinctrl-0 = <&sdmmc1_b4_pins_a>;
>>> +     pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
>>> +     pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
>>> +     cd-gpios = <&gpiob 7 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
>>> +     disable-wp;
>>> +     st,neg-edge;
>>> +     bus-width = <4>;
>>> +     vmmc-supply = <&v3v3>;
>>> +     status = "okay";
>>> +};
>>> +
>>> +&uart4 {
>>> +     pinctrl-names = "default";
>>> +     pinctrl-0 = <&uart4_pins_a>;
>>> +     status = "okay";
>>> +};
>>> +
>>>
>>
>> --
>> Pengutronix e.K.                           |                             |
>> Steuerwalder Str. 21                       | http://www.pengutronix.de/  |
>> 31137 Hildesheim, Germany                  | Phone: +49-5121-206917-0    |
>> Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |
> 

-- 
Pengutronix e.K.                           |                             |
Steuerwalder Str. 21                       | http://www.pengutronix.de/  |
31137 Hildesheim, Germany                  | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |