From mboxrd@z Thu Jan 1 00:00:00 1970 Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1750960AbcKYIHq (ORCPT ); Fri, 25 Nov 2016 03:07:46 -0500 Received: from szxga02-in.huawei.com ([119.145.14.65]:48235 "EHLO szxga02-in.huawei.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1750762AbcKYIHj (ORCPT ); Fri, 25 Nov 2016 03:07:39 -0500 Subject: Re: [PATCH] reset: hisilicon: add a polarity cell for reset line specifier To: Philipp Zabel References: <1479193794-18350-1-git-send-email-xuejiancheng@hisilicon.com> <1479206594.2456.24.camel@pengutronix.de> <03bb74da-6b24-ee4c-307d-3b3f10ac2f7a@hisilicon.com> <2281ff0d-2883-a78c-6106-f913da24581f@hisilicon.com> CC: , , , , , , , , , , , , , , From: Jiancheng Xue Message-ID: Date: Fri, 25 Nov 2016 16:05:03 +0800 User-Agent: Mozilla/5.0 (Windows NT 6.1; WOW64; rv:45.0) Gecko/20100101 Thunderbird/45.3.0 MIME-Version: 1.0 In-Reply-To: <2281ff0d-2883-a78c-6106-f913da24581f@hisilicon.com> Content-Type: text/plain; charset="utf-8" Content-Transfer-Encoding: 7bit X-Originating-IP: [10.67.245.243] X-CFilter-Loop: Reflected Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org On 2016/11/25 11:45, Jiancheng Xue wrote: > > On 2016/11/21 10:58, Jiancheng Xue wrote: >> Hi Philipp, >> >>> On 2016/11/15 18:43, Philipp Zabel wrote: >>>> Hi Jiancheng, >>>> >>>> Am Dienstag, den 15.11.2016, 15:09 +0800 schrieb Jiancheng Xue: >>>>> Add a polarity cell for reset line specifier. If the reset line >>>>> is asserted when the register bit is 1, the polarity is >>>>> normal. Otherwise, it is inverted. >>>>> >>>>> Signed-off-by: Jiancheng Xue >>>>> --- >>> Thank you very much for replying so soon. >>> >>> Please allow me to decribe the reason why this patch exists first. >>> All bits in the reset controller were designed to be active-high. >>> But in a recent chip only one bit was implemented to be active-low :( >>> >>>>> .../devicetree/bindings/clock/hisi-crg.txt | 11 ++++--- >>>>> arch/arm/boot/dts/hi3519.dtsi | 2 +- >>>>> drivers/clk/hisilicon/reset.c | 36 ++++++++++++++++------ >>>>> 3 files changed, 33 insertions(+), 16 deletions(-) >>>>> >>>>> diff --git a/Documentation/devicetree/bindings/clock/hisi-crg.txt b/Documentation/devicetree/bindings/clock/hisi-crg.txt >>>>> index e3919b6..fcbb4f3 100644 >>>>> --- a/Documentation/devicetree/bindings/clock/hisi-crg.txt >>>>> +++ b/Documentation/devicetree/bindings/clock/hisi-crg.txt >>>>> @@ -25,19 +25,20 @@ to specify the clock which they consume. >>>>> >>>>> All these identifier could be found in . >>>>> >>>>> -- #reset-cells: should be 2. >>>>> +- #reset-cells: should be 3. >>>>> >>>>> A reset signal can be controlled by writing a bit register in the CRG module. >>>>> -The reset specifier consists of two cells. The first cell represents the >>>>> +The reset specifier consists of three cells. The first cell represents the >>>>> register offset relative to the base address. The second cell represents the >>>>> -bit index in the register. >>>>> +bit index in the register. The third cell represents the polarity of the reset >>>>> +line (0 for normal, 1 for inverted). >>>> >> #reset-cells: Should be 2 if compatilbe string is "hisilicon,hi3519-crg". Should be 3 otherwise. >> A reset signal can be controlled by writing a bit register in the CRG module. >> The reset specifier consists of two or three cells. The first cell represents the >> register offset relative to the base address. The second cell represents the >> bit index in the register.The third cell represents the polarity of the reset >> line (0 for active-high, 1 for active-low). >> >> If I change the binding like this, can it be accepted? >> > Hi Philipp, > > Could you give me more suggestions about this? If you really don't like changing the > reset-cells like this, I can modify the patch according to your suggestions. > Thank you. > I'll drop this patch and use "ti,syscon-reset" instead to resolve the polarity issue. Thanks. Regards, Jiancheng