[PATCH 18/37] docs: networking: device drivers: convert davicom/dm9000.txt to ReST

[Mauro Carvalho Chehab <mchehab+huawei@kernel.org>]

- add SPDX header;
- add a document title;
- mark lists as such;
- mark tables as such;
- mark code blocks and literals as such;
- use the right horizontal tag markup;
- adjust identation, whitespaces and blank lines where needed;
- add to networking/index.rst.

Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
---
 .../davicom/{dm9000.txt => dm9000.rst}        | 24 +++++++++++--------
 .../networking/device_drivers/index.rst       |  1 +
 2 files changed, 15 insertions(+), 10 deletions(-)
 rename Documentation/networking/device_drivers/davicom/{dm9000.txt => dm9000.rst} (92%)

diff --git a/Documentation/networking/device_drivers/davicom/dm9000.txt b/Documentation/networking/device_drivers/davicom/dm9000.rst
similarity index 92%
rename from Documentation/networking/device_drivers/davicom/dm9000.txt
rename to Documentation/networking/device_drivers/davicom/dm9000.rst
index 5552e2e575c5..d5458da01083 100644
--- a/Documentation/networking/device_drivers/davicom/dm9000.txt
+++ b/Documentation/networking/device_drivers/davicom/dm9000.rst
@@ -1,7 +1,11 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+=====================
 DM9000 Network driver
 =====================
 
 Copyright 2008 Simtec Electronics,
+
 	  Ben Dooks <ben@simtec.co.uk> <ben-linux@fluff.org>
 
 
@@ -30,9 +34,9 @@ These resources should be specified in that order, as the ordering of the
 two address regions is important (the driver expects these to be address
 and then data).
 
-An example from arch/arm/mach-s3c2410/mach-bast.c is:
+An example from arch/arm/mach-s3c2410/mach-bast.c is::
 
-static struct resource bast_dm9k_resource[] = {
+  static struct resource bast_dm9k_resource[] = {
 	[0] = {
 		.start = S3C2410_CS5 + BAST_PA_DM9000,
 		.end   = S3C2410_CS5 + BAST_PA_DM9000 + 3,
@@ -48,14 +52,14 @@ static struct resource bast_dm9k_resource[] = {
 		.end   = IRQ_DM9000,
 		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
 	}
-};
+  };
 
-static struct platform_device bast_device_dm9k = {
+  static struct platform_device bast_device_dm9k = {
 	.name		= "dm9000",
 	.id		= 0,
 	.num_resources	= ARRAY_SIZE(bast_dm9k_resource),
 	.resource	= bast_dm9k_resource,
-};
+  };
 
 Note the setting of the IRQ trigger flag in bast_dm9k_resource[2].flags,
 as this will generate a warning if it is not present. The trigger from
@@ -64,13 +68,13 @@ handler to ensure that the IRQ is setup correctly.
 
 This shows a typical platform device, without the optional configuration
 platform data supplied. The next example uses the same resources, but adds
-the optional platform data to pass extra configuration data:
+the optional platform data to pass extra configuration data::
 
-static struct dm9000_plat_data bast_dm9k_platdata = {
+  static struct dm9000_plat_data bast_dm9k_platdata = {
 	.flags		= DM9000_PLATF_16BITONLY,
-};
+  };
 
-static struct platform_device bast_device_dm9k = {
+  static struct platform_device bast_device_dm9k = {
 	.name		= "dm9000",
 	.id		= 0,
 	.num_resources	= ARRAY_SIZE(bast_dm9k_resource),
@@ -78,7 +82,7 @@ static struct platform_device bast_device_dm9k = {
 	.dev		= {
 		.platform_data = &bast_dm9k_platdata,
 	}
-};
+  };
 
 The platform data is defined in include/linux/dm9000.h and described below.
 
diff --git a/Documentation/networking/device_drivers/index.rst b/Documentation/networking/device_drivers/index.rst
index 0b39342e2a1f..e8db57fef2e9 100644
--- a/Documentation/networking/device_drivers/index.rst
+++ b/Documentation/networking/device_drivers/index.rst
@@ -33,6 +33,7 @@ Contents:
    aquantia/atlantic
    chelsio/cxgb
    cirrus/cs89x0
+   davicom/dm9000
 
 .. only::  subproject and html
 
-- 
2.25.4