Re: [PATCH v4 05/14] drm/mxsfb: Update register definitions using bit manipulation defines

[Stefan Agner <stefan@agner.ch>]

On 2019-08-29 13:30, Robert Chiras wrote:
> Use BIT(x) and GEN_MASK(h, l) for better representation the inside of
> various registers.
> 
> Signed-off-by: Robert Chiras <robert.chiras@nxp.com>
> Tested-by: Guido Günther <agx@sigxcpu.org>
> ---
>  drivers/gpu/drm/mxsfb/mxsfb_regs.h | 151 ++++++++++++++++++++++---------------
>  1 file changed, 89 insertions(+), 62 deletions(-)
> 
> diff --git a/drivers/gpu/drm/mxsfb/mxsfb_regs.h
> b/drivers/gpu/drm/mxsfb/mxsfb_regs.h
> index 71426aa..9fcb1db 100644
> --- a/drivers/gpu/drm/mxsfb/mxsfb_regs.h
> +++ b/drivers/gpu/drm/mxsfb/mxsfb_regs.h
> @@ -40,66 +40,93 @@
>  #define LCDC_AS_BUF			0x220
>  #define LCDC_AS_NEXT_BUF		0x230
>  
> -#define CTRL_SFTRST			(1 << 31)
> -#define CTRL_CLKGATE			(1 << 30)
> -#define CTRL_BYPASS_COUNT		(1 << 19)
> -#define CTRL_VSYNC_MODE			(1 << 18)
> -#define CTRL_DOTCLK_MODE		(1 << 17)
> -#define CTRL_DATA_SELECT		(1 << 16)
> -#define CTRL_SET_BUS_WIDTH(x)		(((x) & 0x3) << 10)
> -#define CTRL_GET_BUS_WIDTH(x)		(((x) >> 10) & 0x3)
> -#define CTRL_BUS_WIDTH_MASK		(0x3 << 10)
> -#define CTRL_SET_WORD_LENGTH(x)		(((x) & 0x3) << 8)
> -#define CTRL_GET_WORD_LENGTH(x)		(((x) >> 8) & 0x3)
> -#define CTRL_MASTER			(1 << 5)
> -#define CTRL_DF16			(1 << 3)
> -#define CTRL_DF18			(1 << 2)
> -#define CTRL_DF24			(1 << 1)
> -#define CTRL_RUN			(1 << 0)
> -
> -#define CTRL1_RECOVERY_ON_UNDERFLOW	(1 << 24)
> -#define CTRL1_FIFO_CLEAR		(1 << 21)
> -#define CTRL1_SET_BYTE_PACKAGING(x)	(((x) & 0xf) << 16)
> -#define CTRL1_GET_BYTE_PACKAGING(x)	(((x) >> 16) & 0xf)
> -#define CTRL1_CUR_FRAME_DONE_IRQ_EN	(1 << 13)
> -#define CTRL1_CUR_FRAME_DONE_IRQ	(1 << 9)
> -
> -#define CTRL2_OUTSTANDING_REQS__REQ_16		(4 << 21)
> -

This is introduced two patches earlier just to be removed here. I
suggest to reorder this patch in front of "drm/mxsfb: Add defines for
the rest of registers", basically convert first to using BIT/GENMASK
etc, and then introduce the new request.


> -#define TRANSFER_COUNT_SET_VCOUNT(x)	(((x) & 0xffff) << 16)
> -#define TRANSFER_COUNT_GET_VCOUNT(x)	(((x) >> 16) & 0xffff)
> -#define TRANSFER_COUNT_SET_HCOUNT(x)	((x) & 0xffff)
> -#define TRANSFER_COUNT_GET_HCOUNT(x)	((x) & 0xffff)
> -
> -#define VDCTRL0_ENABLE_PRESENT		(1 << 28)
> -#define VDCTRL0_VSYNC_ACT_HIGH		(1 << 27)
> -#define VDCTRL0_HSYNC_ACT_HIGH		(1 << 26)
> -#define VDCTRL0_DOTCLK_ACT_FALLING	(1 << 25)
> -#define VDCTRL0_ENABLE_ACT_HIGH		(1 << 24)
> -#define VDCTRL0_VSYNC_PERIOD_UNIT	(1 << 21)
> -#define VDCTRL0_VSYNC_PULSE_WIDTH_UNIT	(1 << 20)
> -#define VDCTRL0_HALF_LINE		(1 << 19)
> -#define VDCTRL0_HALF_LINE_MODE		(1 << 18)
> -#define VDCTRL0_SET_VSYNC_PULSE_WIDTH(x) ((x) & 0x3ffff)
> -#define VDCTRL0_GET_VSYNC_PULSE_WIDTH(x) ((x) & 0x3ffff)
> -
> -#define VDCTRL2_SET_HSYNC_PERIOD(x)	((x) & 0x3ffff)
> -#define VDCTRL2_GET_HSYNC_PERIOD(x)	((x) & 0x3ffff)
> -
> -#define VDCTRL3_MUX_SYNC_SIGNALS	(1 << 29)
> -#define VDCTRL3_VSYNC_ONLY		(1 << 28)
> -#define SET_HOR_WAIT_CNT(x)		(((x) & 0xfff) << 16)
> -#define GET_HOR_WAIT_CNT(x)		(((x) >> 16) & 0xfff)
> -#define SET_VERT_WAIT_CNT(x)		((x) & 0xffff)
> -#define GET_VERT_WAIT_CNT(x)		((x) & 0xffff)
> -
> -#define VDCTRL4_SET_DOTCLK_DLY(x)	(((x) & 0x7) << 29) /* v4 only */
> -#define VDCTRL4_GET_DOTCLK_DLY(x)	(((x) >> 29) & 0x7) /* v4 only */
> -#define VDCTRL4_SYNC_SIGNALS_ON		(1 << 18)
> -#define SET_DOTCLK_H_VALID_DATA_CNT(x)	((x) & 0x3ffff)
> -
> -#define DEBUG0_HSYNC			(1 < 26)
> -#define DEBUG0_VSYNC			(1 < 25)
> +/* reg bit manipulation */
> +#define REG_PUT(x, h, l) (((x) << (l)) & GENMASK(h, l))
> +#define REG_GET(x, h, l) (((x) & GENMASK(h, l)) >> (l))
> +
> +#define CTRL_SFTRST			BIT(31)
> +#define CTRL_CLKGATE			BIT(30)
> +#define CTRL_SHIFT_DIR(x)		REG_PUT((x), 26, 26)
> +#define CTRL_SHIFT_NUM(x)		REG_PUT((x), 25, 21)
> +#define CTRL_BYPASS_COUNT		BIT(19)
> +#define CTRL_VSYNC_MODE			BIT(18)
> +#define CTRL_DOTCLK_MODE		BIT(17)
> +#define CTRL_DATA_SELECT		BIT(16)
> +#define CTRL_INPUT_SWIZZLE(x)		REG_PUT((x), 15, 14)
> +#define CTRL_CSC_SWIZZLE(x)		REG_PUT((x), 13, 12)
> +#define CTRL_SET_BUS_WIDTH(x)		REG_PUT((x), 11, 10)
> +#define CTRL_GET_BUS_WIDTH(x)		REG_GET((x), 11, 10)
> +#define CTRL_BUS_WIDTH_MASK		REG_PUT((0x3), 11, 10)
> +#define CTRL_SET_WORD_LENGTH(x)		REG_PUT((x), 9, 8)
> +#define CTRL_GET_WORD_LENGTH(x)		REG_GET((x), 9, 8)
> +#define CTRL_MASTER			BIT(5)
> +#define CTRL_DF16			BIT(3)
> +#define CTRL_DF18			BIT(2)
> +#define CTRL_DF24			BIT(1)
> +#define CTRL_RUN			BIT(0)
> +
> +#define CTRL1_RECOVERY_ON_UNDERFLOW	BIT(24)
> +#define CTRL1_FIFO_CLEAR		BIT(21)
> +
> +/*
> + * BYTE_PACKAGING
> + *
> + * This bitfield is used to show which data bytes in a 32-bit word area valid.
> + * Default value 0xf indicates that all bytes are valid. For 8-bit transfers,
> + * any combination in this bitfield will mean valid data is present in the
> + * corresponding bytes. In the 16-bit mode, a 16-bit half-word is valid only if
> + * adjacent bits [1:0] or [3:2] or both are 1. A value of 0x0 will mean that
> + * none of the bytes are valid and should not be used. For example, set the bit
> + * field value to 0x7 if the display data is arranged in the 24-bit unpacked
> + * format (A-R-G-B where A value does not have be transmitted).
> + */
> +#define CTRL1_SET_BYTE_PACKAGING(x)	REG_PUT((x), 19, 16)
> +#define CTRL1_GET_BYTE_PACKAGING(x)	REG_GET((x), 19, 16)
> +
> +#define CTRL1_CUR_FRAME_DONE_IRQ_EN	BIT(13)
> +#define CTRL1_CUR_FRAME_DONE_IRQ	BIT(9)
> +
> +#define CTRL2_OUTSTANDING_REQS(x)	REG_PUT((x), 23, 21)
> +#define REQ_1	0
> +#define REQ_2	1
> +#define REQ_4	2
> +#define REQ_8	3
> +#define REQ_16	4

Can you prefix them with CTRL2_? I think it is more in line with other
defines.

--
Stefan

> +
> +#define TRANSFER_COUNT_SET_VCOUNT(x)	REG_PUT((x), 31, 16)
> +#define TRANSFER_COUNT_GET_VCOUNT(x)	REG_GET((x), 31, 16)
> +#define TRANSFER_COUNT_SET_HCOUNT(x)	REG_PUT((x), 15, 0)
> +#define TRANSFER_COUNT_GET_HCOUNT(x)	REG_GET((x), 15, 0)
> +
> +#define VDCTRL0_ENABLE_PRESENT		BIT(28)
> +#define VDCTRL0_VSYNC_ACT_HIGH		BIT(27)
> +#define VDCTRL0_HSYNC_ACT_HIGH		BIT(26)
> +#define VDCTRL0_DOTCLK_ACT_FALLING	BIT(25)
> +#define VDCTRL0_ENABLE_ACT_HIGH		BIT(24)
> +#define VDCTRL0_VSYNC_PERIOD_UNIT	BIT(21)
> +#define VDCTRL0_VSYNC_PULSE_WIDTH_UNIT	BIT(20)
> +#define VDCTRL0_HALF_LINE		BIT(19)
> +#define VDCTRL0_HALF_LINE_MODE		BIT(18)
> +#define VDCTRL0_SET_VSYNC_PULSE_WIDTH(x) REG_PUT((x), 17, 0)
> +#define VDCTRL0_GET_VSYNC_PULSE_WIDTH(x) REG_GET((x), 17, 0)
> +
> +#define VDCTRL2_SET_HSYNC_PERIOD(x)	REG_PUT((x), 15, 0)
> +#define VDCTRL2_GET_HSYNC_PERIOD(x)	REG_GET((x), 15, 0)
> +
> +#define VDCTRL3_MUX_SYNC_SIGNALS	BIT(29)
> +#define VDCTRL3_VSYNC_ONLY		BIT(28)
> +#define SET_HOR_WAIT_CNT(x)		REG_PUT((x), 27, 16)
> +#define GET_HOR_WAIT_CNT(x)		REG_GET((x), 27, 16)
> +#define SET_VERT_WAIT_CNT(x)		REG_PUT((x), 15, 0)
> +#define GET_VERT_WAIT_CNT(x)		REG_GET((x), 15, 0)
> +
> +#define VDCTRL4_SET_DOTCLK_DLY(x)	REG_PUT((x), 31, 29) /* v4 only */
> +#define VDCTRL4_GET_DOTCLK_DLY(x)	REG_GET((x), 31, 29) /* v4 only */
> +#define VDCTRL4_SYNC_SIGNALS_ON		BIT(18)
> +#define SET_DOTCLK_H_VALID_DATA_CNT(x)	REG_PUT((x), 17, 0)
> +
> +#define DEBUG0_HSYNC			BIT(26)
> +#define DEBUG0_VSYNC			BIT(25)
>  
>  #define MXSFB_MIN_XRES			120
>  #define MXSFB_MIN_YRES			120
> @@ -116,7 +143,7 @@
>  #define STMLCDIF_18BIT 2 /* pixel data bus to the display is of 18 bit width */
>  #define STMLCDIF_24BIT 3 /* pixel data bus to the display is of 24 bit width */
>  
> -#define MXSFB_SYNC_DATA_ENABLE_HIGH_ACT	(1 << 6)
> -#define MXSFB_SYNC_DOTCLK_FALLING_ACT	(1 << 7) /* negative edge sampling */
> +#define MXSFB_SYNC_DATA_ENABLE_HIGH_ACT	BIT(6)
> +#define MXSFB_SYNC_DOTCLK_FALLING_ACT	BIT(7) /* negative edge sampling */
>  
>  #endif /* __MXSFB_REGS_H__ */