From: Michael Walle <michael@walle.cc>
To: Tudor.Ambarus@microchip.com
Cc: linux-mtd@lists.infradead.org, linux-kernel@vger.kernel.org,
miquel.raynal@bootlin.com, richard@nod.at, vigneshr@ti.com,
boris.brezillon@collabora.com
Subject: Re: [PATCH v5 3/3] mtd: spi-nor: keep lock bits if they are non-volatile
Date: Thu, 26 Nov 2020 21:46:43 +0100 [thread overview]
Message-ID: <d91447d56e9f75f0eda8561c47677e44@walle.cc> (raw)
In-Reply-To: <f6344b9cb5c61c3bfd075e231b708269@walle.cc>
Am 2020-11-25 19:52, schrieb Michael Walle:
> Am 2020-11-25 13:21, schrieb Tudor.Ambarus@microchip.com:
[..]
>>> diff --git a/drivers/mtd/spi-nor/esmt.c b/drivers/mtd/spi-nor/esmt.c
>>> index c93170008118..c2ebf29d95f2 100644
>>> --- a/drivers/mtd/spi-nor/esmt.c
>>> +++ b/drivers/mtd/spi-nor/esmt.c
>>> @@ -11,9 +11,13 @@
>>> static const struct flash_info esmt_parts[] = {
>>> /* ESMT */
>>> { "f25l32pa", INFO(0x8c2016, 0, 64 * 1024, 64,
>>> - SECT_4K | SPI_NOR_HAS_LOCK) },
>>> + SECT_4K | SPI_NOR_HAS_LOCK |
>>> SPI_NOR_WP_IS_VOLATILE) },
>>
>> https://www.esmt.com.tw/upload/pdf/ESMT/datasheets/F25L32PA.pdf
>> BP GENMASK(4,2), volatile, ok
>>
>>> { "f25l32qa", INFO(0x8c4116, 0, 64 * 1024, 64,
>>> - SECT_4K | SPI_NOR_HAS_LOCK) },
>>> + SECT_4K | SPI_NOR_HAS_LOCK |
>>> SPI_NOR_WP_IS_VOLATILE) },
>>
>> https://datasheetspdf.com/pdf-file/796196/ESMT/F25L32QA/1
>> Datasheet states that "BP0~3, QE and BPL bits are non-volatile."
>> At the same time, it says: "After power-up, BP3, BP2, BP1 and BP0 bits
>> are set to 0."
>
> Mhh I had this datasheet:
> https://www.esmt.com.tw/upload/pdf/ESMT/datasheets/F25L32QA.pdf
>
> In that one they are volatile.. but yours is a newer version. So I
> guess the flashes with the PA suffix have volatile BP and the QA ones
> have the non-volatile version.
>
>> Maybe factory default setting for BPn is 0? Let's treat them as NV, as
>> in
>> f25l64qa.
>
> Yes will fix it.
>
>> Do we need BP3?
>
> Rather the top bottom bit. But that is outside of the scope of this
> patch.
> And as per your rule, as I don't have this particular flash I cannot
> test
> and thus couldn't add the TB bit (technically). But if you like I can
> do
> another patch (outside of this series and after it is applied) which
> will
> add the TB bit flag.
I've had a closer look at this. The top/bottom behavior is different
to that what we support in spi_nor_sr_lock(). But on the upside, the
current code is correct; it just doesn't support the TB bit. So we can
only protect addresses starting from the top. No changes needed here.
>>
>>> + /*
>>> + * According to the datasheet the BPn bits are non-volatile,
>>> whereas
>>> + * they are volatile for the smaller f25l32qa.
>>> + */
>>> { "f25l64qa", INFO(0x8c4117, 0, 64 * 1024, 128,
>>> SECT_4K | SPI_NOR_HAS_LOCK) },
>>
>> https://datasheetspdf.com/pdf-file/967488/EliteSemiconductor/F25L64QA/1
>> BP GENMASK(5, 2), non-volatile.
>>
>> BP3?
>
> Same as F25L32QA.
[..]
>>> diff --git a/drivers/mtd/spi-nor/sst.c b/drivers/mtd/spi-nor/sst.c
>>> index 8b169fa4102a..5e4450877d66 100644
>>> --- a/drivers/mtd/spi-nor/sst.c
>>> +++ b/drivers/mtd/spi-nor/sst.c
>>> @@ -11,26 +11,27 @@
>>> static const struct flash_info sst_parts[] = {
>>> /* SST -- large erase sizes are "overlays", "sectors" are 4K
>>> */
>>> { "sst25vf040b", INFO(0xbf258d, 0, 64 * 1024, 8,
>>> - SECT_4K | SST_WRITE | SPI_NOR_HAS_LOCK)
>>> },
>>> + SECT_4K | SST_WRITE | SPI_NOR_HAS_LOCK
>>> | SPI_NOR_WP_IS_VOLATILE) },
>>> { "sst25vf080b", INFO(0xbf258e, 0, 64 * 1024, 16,
>>> - SECT_4K | SST_WRITE | SPI_NOR_HAS_LOCK)
>>> },
>>> + SECT_4K | SST_WRITE | SPI_NOR_HAS_LOCK
>>> | SPI_NOR_WP_IS_VOLATILE) },
>>> { "sst25vf016b", INFO(0xbf2541, 0, 64 * 1024, 32,
>>> - SECT_4K | SST_WRITE | SPI_NOR_HAS_LOCK)
>>> },
>>> + SECT_4K | SST_WRITE | SPI_NOR_HAS_LOCK
>>> | SPI_NOR_WP_IS_VOLATILE) },
>>> { "sst25vf032b", INFO(0xbf254a, 0, 64 * 1024, 64,
>>> - SECT_4K | SST_WRITE | SPI_NOR_HAS_LOCK)
>>> },
>>> - { "sst25vf064c", INFO(0xbf254b, 0, 64 * 1024, 128, SECT_4K |
>>> SPI_NOR_HAS_LOCK) },
>>> + SECT_4K | SST_WRITE | SPI_NOR_HAS_LOCK
>>> | SPI_NOR_WP_IS_VOLATILE) },
>>> + { "sst25vf064c", INFO(0xbf254b, 0, 64 * 1024, 128,
>>> + SECT_4K | SPI_NOR_HAS_LOCK |
>>> SPI_NOR_WP_IS_VOLATILE) },
>>
>> Looks like BP3 is needed here.
>
> https://ww1.microchip.com/downloads/en/DeviceDoc/20005036C.pdf
>
> agreed. But again cannot test it. Would add it as a seperate patch
> to this series. (or leave it like it is)
I'll look at this tomorrow.
-michael
>>
>>> { "sst25wf512", INFO(0xbf2501, 0, 64 * 1024, 1,
>>> - SECT_4K | SST_WRITE | SPI_NOR_HAS_LOCK)
>>> },
>>> + SECT_4K | SST_WRITE | SPI_NOR_HAS_LOCK
>>> | SPI_NOR_WP_IS_VOLATILE) },
>>> { "sst25wf010", INFO(0xbf2502, 0, 64 * 1024, 2,
>>> - SECT_4K | SST_WRITE | SPI_NOR_HAS_LOCK)
>>> },
>>> + SECT_4K | SST_WRITE | SPI_NOR_HAS_LOCK
>>> | SPI_NOR_WP_IS_VOLATILE) },
>>> { "sst25wf020", INFO(0xbf2503, 0, 64 * 1024, 4,
>>> - SECT_4K | SST_WRITE | SPI_NOR_HAS_LOCK)
>>> },
>>> + SECT_4K | SST_WRITE | SPI_NOR_HAS_LOCK
>>> | SPI_NOR_WP_IS_VOLATILE) },
>>> { "sst25wf020a", INFO(0x621612, 0, 64 * 1024, 4, SECT_4K |
>>> SPI_NOR_HAS_LOCK) },
>>> { "sst25wf040b", INFO(0x621613, 0, 64 * 1024, 8, SECT_4K |
>>> SPI_NOR_HAS_LOCK) },
>>
>> These two flashes have just two BP bits located at bit 2 and 3.
>> Probably will work.
>
> Mhh? What datasheet were you looking at? There are three BPs:
> https://ww1.microchip.com/downloads/en/DeviceDoc/SST25WF040B-4-Mbit-1.8V-SPI-Serial-Flash-Data-Sheet-DS20005193E.pdf
>
> Ahh here are the tables which only inidicate two. But there are three.
> https://ww1.microchip.com/downloads/en/DeviceDoc/20005016C.pdf
>
> And yes since the rework of the BP bits algorithm this should work
> as expected. Its just because the flash is too small to actually fill
> up all the BP bits.
>
> -michael
next prev parent reply other threads:[~2020-11-26 20:46 UTC|newest]
Thread overview: 17+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-10-03 15:32 [PATCH v5 0/3] mtd: spi-nor: keep lock bits if they are non-volatile Michael Walle
2020-10-03 15:32 ` [PATCH v5 1/3] mtd: spi-nor: atmel: remove global protection flag Michael Walle
2020-11-24 19:09 ` Tudor.Ambarus
2020-11-25 18:17 ` Michael Walle
2020-11-26 12:45 ` Tudor.Ambarus
2020-11-26 12:59 ` Tudor.Ambarus
2020-11-26 16:42 ` Tudor.Ambarus
2020-11-26 18:44 ` Michael Walle
2020-10-03 15:32 ` [PATCH v5 2/3] mtd: spi-nor: sst: " Michael Walle
2020-11-24 19:50 ` Tudor.Ambarus
2020-10-03 15:32 ` [PATCH v5 3/3] mtd: spi-nor: keep lock bits if they are non-volatile Michael Walle
2020-11-25 12:21 ` Tudor.Ambarus
2020-11-25 18:52 ` Michael Walle
2020-11-26 16:47 ` Tudor.Ambarus
2020-11-26 20:46 ` Michael Walle [this message]
2020-10-27 22:26 ` [PATCH v5 0/3] " Michael Walle
2020-11-10 13:07 ` Vignesh Raghavendra
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=d91447d56e9f75f0eda8561c47677e44@walle.cc \
--to=michael@walle.cc \
--cc=Tudor.Ambarus@microchip.com \
--cc=boris.brezillon@collabora.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mtd@lists.infradead.org \
--cc=miquel.raynal@bootlin.com \
--cc=richard@nod.at \
--cc=vigneshr@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).