From: David Lechner <david@lechnology.com>
To: "Noralf Trønnes" <noralf@tronnes.org>,
dri-devel@lists.freedesktop.org, devicetree@vger.kernel.org
Cc: Daniel Vetter <daniel@ffwll.ch>, David Airlie <airlied@linux.ie>,
Rob Herring <robh+dt@kernel.org>,
Mark Rutland <mark.rutland@arm.com>, Sekhar Nori <nsekhar@ti.com>,
Kevin Hilman <khilman@kernel.org>,
linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org
Subject: Re: [PATCH v3 3/6] dt-bindings: add binding for Sitronix ST7586 display panels
Date: Fri, 4 Aug 2017 11:51:22 -0500 [thread overview]
Message-ID: <e824aca6-b668-1d63-65a0-c56bfd8bec79@lechnology.com> (raw)
In-Reply-To: <66f0b765-928e-1fca-9588-99da747749a5@tronnes.org>
On 08/04/2017 04:48 AM, Noralf Trønnes wrote:
>
> Den 04.08.2017 00.33, skrev David Lechner:
>> This adds a new binding for Sitronix ST7586 display panels.
>>
>> Using lego as the vendor prefix in the compatible string because the
>> display
>> panel I am working with is an integral part of the LEGO MINDSTORMS EV3.
>
> Is this display available outside of this Lego part?
No, it is not.
> If not you can remove the properties you don't need for this particular
> display setup. Another st7586 display with a different panel would need
> a different initialization sequence and compatible string, so we can
> add properties when/if that happens.
OK. so I will drop power-supply and backlight.
Should I remove these from the driver as well? There are some panels out
there that could use them.[1]
[1]:
http://www.buydisplay.com/download/manual/ERC240160-1_Series_Datasheet.pdf
>
> Noralf.
>
>> Signed-off-by: David Lechner <david@lechnology.com>
>> ---
>> .../bindings/display/sitronix,st7586.txt | 26
>> ++++++++++++++++++++++
>> 1 file changed, 26 insertions(+)
>> create mode 100644
>> Documentation/devicetree/bindings/display/sitronix,st7586.txt
>>
>> diff --git
>> a/Documentation/devicetree/bindings/display/sitronix,st7586.txt
>> b/Documentation/devicetree/bindings/display/sitronix,st7586.txt
>> new file mode 100644
>> index 0000000..dfb0b7b
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/display/sitronix,st7586.txt
>> @@ -0,0 +1,26 @@
>> +Sitronix ST7586 display panel
>> +
>> +Required properties:
>> +- compatible: "lego,ev3-lcd".
>> +
>> +The node for this driver must be a child node of a SPI controller, hence
>> +all mandatory properties described in ../spi/spi-bus.txt must be
>> specified.
>> +
>> +Optional properties:
>> +- dc-gpios: D/C pin. The presence/absence of this GPIO determines
>> + the panel interface operation mode (IF[3:1] pins):
>> + - present: IF=011 4-wire 8-bit data serial interface
>> + - absent: IF=010 3-wire 9-bit data serial interface
>> +- reset-gpios: Reset pin
>> +- power-supply: A regulator node for the supply voltage.
>> +- backlight: phandle of the backlight device attached to the panel
>> +- rotation: panel rotation in degrees counter clockwise
>> (0,90,180,270)
>> +
>> +Example:
>> + display@0{
>> + compatible = "lego,ev3-lcd";
>> + reg = <0>;
>> + spi-max-frequency = <10000000>;
>> + dc-gpios = <&gpio 43 GPIO_ACTIVE_HIGH>;
>> + reset-gpios = <&gpio 80 GPIO_ACTIVE_HIGH>;
>> + };
>
next prev parent reply other threads:[~2017-08-04 16:51 UTC|newest]
Thread overview: 21+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-08-03 22:33 [PATCH v3 0/6] Support for LEGO MINDSTORMS EV3 LCD display David Lechner
2017-08-03 22:33 ` [PATCH v3 1/6] drm/tinydrm: remove call to mipi_dbi_init() from mipi_dbi_spi_init() David Lechner
2017-08-04 13:16 ` Noralf Trønnes
2017-08-03 22:33 ` [PATCH v3 2/6] drm/tinydrm: generalize tinydrm_xrgb8888_to_gray8() David Lechner
2017-08-04 7:27 ` Noralf Trønnes
2017-08-04 13:20 ` Noralf Trønnes
2017-08-03 22:33 ` [PATCH v3 3/6] dt-bindings: add binding for Sitronix ST7586 display panels David Lechner
2017-08-04 9:48 ` Noralf Trønnes
2017-08-04 16:51 ` David Lechner [this message]
2017-08-04 18:04 ` Noralf Trønnes
2017-08-04 14:54 ` Laurent Pinchart
2017-08-04 15:51 ` David Lechner
2017-08-04 19:39 ` Laurent Pinchart
2017-08-05 16:13 ` David Lechner
2017-08-04 17:36 ` Noralf Trønnes
2017-08-03 22:33 ` [PATCH v3 4/6] drm/tinydrm: add support for LEGO MINDSTORMS EV3 LCD David Lechner
2017-08-05 18:19 ` Noralf Trønnes
2017-08-05 19:54 ` Noralf Trønnes
2017-08-07 16:03 ` David Lechner
2017-08-03 22:33 ` [PATCH v3 5/6] ARM: dts: da850-lego-ev3: Add node for LCD display David Lechner
2017-08-03 22:33 ` [PATCH v3 6/6] ARM: davinci_all_defconfig: enable tinydrm and ST7586 David Lechner
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=e824aca6-b668-1d63-65a0-c56bfd8bec79@lechnology.com \
--to=david@lechnology.com \
--cc=airlied@linux.ie \
--cc=daniel@ffwll.ch \
--cc=devicetree@vger.kernel.org \
--cc=dri-devel@lists.freedesktop.org \
--cc=khilman@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=noralf@tronnes.org \
--cc=nsekhar@ti.com \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).