linux-kernel.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Shawn Lin <shawn.lin@rock-chips.com>
To: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Cc: Heiko Stuebner <heiko@sntech.de>,
	shawn.lin@rock-chips.com, Mark Rutland <mark.rutland@arm.com>,
	devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
	linux-rockchip@lists.infradead.org,
	Rob Herring <robh+dt@kernel.org>,
	Enric Balletbo i Serra <enric.balletbo@collabora.com>,
	Ezequiel Garcia <ezequiel@collabora.com>,
	linux-arm-kernel@lists.infradead.org
Subject: Re: [PATCH v3] arm64: dts: rockchip: Add DT for nanopc-t4
Date: Tue, 27 Nov 2018 08:45:13 +0800	[thread overview]
Message-ID: <e9ee8167-c398-c14e-d798-3b4233ba2ff2@rock-chips.com> (raw)
In-Reply-To: <26178858.xdqtN7Rtck@phil>

On 2018/11/27 7:48, Heiko Stuebner wrote:
> Hi Tomeu,
> 
> Am Montag, 26. November 2018, 15:47:49 CET schrieb Tomeu Vizoso:
>> This adds a device tree for the NanoPC-T4 SBC, which is based on the
>> Rockchip RK3399 SoC and marketed by FriendlyELEC.
>>
>> Known working:
>>
>> - Serial
>> - Ethernet
>> - HDMI
>> - USB 2.0
>>
>> All of the interesting stuff is in a .dtsi because there are at least
>> two other boards that share most of it: NanoPi M4 and NanoPi NEO4.
>>
>> Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
> 
> looks pretty good overall, just some more small-scale things
> below.
> 
>> ---
>>
>> v2: - Rename compatible from friendlyelec to friendlyarm, to match
>>        existing bindings
>>      - Remove superfluous node spi1
>>
>> v3: - Rewrite regulator tree to match the schematics (Heiko)
>>      - Sort top-level nodes alphabetically (Heiko)
>>      - Used defines for GPIO numbers (Heiko)
>>      - Enabled rga (Heiko)
>>      - Removed cdn_dp node (Heiko)
>>      - Removed dependencies to fusb0 as extcon (Heiko)
>>      - Removed superfluous properties (Heiko)
> 
> 
>> diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
>> index 49042c477870..4cbd2c461052 100644
>> --- a/arch/arm64/boot/dts/rockchip/Makefile
>> +++ b/arch/arm64/boot/dts/rockchip/Makefile
>> @@ -1,6 +1,7 @@
>>   # SPDX-License-Identifier: GPL-2.0
>>   dtb-$(CONFIG_ARCH_ROCKCHIP) += px30-evb.dtb
>>   dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-evb.dtb
>> +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-nanopc-t4.dtb
>>   dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-rock64.dtb
>>   dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-roc-cc.dtb
>>   dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-evb-act8846.dtb
> 
> These are definitly sorted in the Makefile, so this should move between
> rk3399-gru-scarlet-kd.dtb and rk3399-puma-haikou.dtb :-)
> 
> 
>> diff --git a/arch/arm64/boot/dts/rockchip/rk3399-nanopi4.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-nanopi4.dtsi
>> new file mode 100644
>> index 000000000000..f102ff2317c3
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/rockchip/rk3399-nanopi4.dtsi
>> @@ -0,0 +1,740 @@
>> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
>> +/*
>> + * RK3399-based FriendlyElec boards device tree source
>> + *
>> + * Copyright (c) 2016 Fuzhou Rockchip Electronics Co., Ltd
>> + *
>> + * Copyright (c) 2018 FriendlyElec Computer Tech. Co., Ltd.
>> + * (http://www.friendlyarm.com)
>> + *
>> + * Copyright (c) 2018 Collabora Ltd.
>> + */
>> +
>> +/dts-v1/;
>> +#include <dt-bindings/input/linux-event-codes.h>
>> +#include "rk3399.dtsi"
>> +#include "rk3399-opp.dtsi"
>> +
>> +/ {
>> +	chosen {
>> +		stdout-path = "serial2:1500000n8";
>> +	};
>> +
>> +	clkin_gmac: external-gmac-clock {
>> +		compatible = "fixed-clock";
>> +		clock-frequency = <125000000>;
>> +		clock-output-names = "clkin_gmac";
>> +		#clock-cells = <0>;
>> +	};
>> +
>> +	vdd_5v: vdd_5v {
>> +		compatible = "regulator-fixed";
>> +		regulator-name = "vdd_5v";
>> +		regulator-always-on;
>> +		regulator-boot-on;
>> +	};
>> +
>> +	vcc5v0_core: vcc5v0_core {
>> +		compatible = "regulator-fixed";
>> +		regulator-name = "vcc5v0_core";
>> +		regulator-always-on;
>> +		regulator-boot-on;
>> +		vin-supply = <&vdd_5v>;
>> +	};
>> +
>> +	vcc3v3_sys: vcc3v3_sys {
>> +		compatible = "regulator-fixed";
>> +		regulator-name = "vcc3v3_sys";
>> +		regulator-always-on;
>> +		regulator-boot-on;
>> +		regulator-min-microvolt = <3300000>;
>> +		regulator-max-microvolt = <3300000>;
>> +		vin-supply = <&vcc5v0_core>;
>> +	};
>> +
>> +	vcc5v0_sys: vcc5v0_sys {
>> +		compatible = "regulator-fixed";
>> +		regulator-name = "vcc5v0_sys";
>> +		regulator-always-on;
>> +		regulator-boot-on;
>> +		regulator-min-microvolt = <5000000>;
>> +		regulator-max-microvolt = <5000000>;
>> +		vin-supply = <&vdd_5v>;
>> +	};
>> +
>> +	vcc5v0_usb1: vcc5v0_usb1 {
>> +		compatible = "regulator-fixed";
>> +		regulator-name = "vcc5v0_usb1";
>> +		regulator-always-on;
>> +		regulator-boot-on;
>> +		vin-supply = <&vcc5v0_sys>;
>> +	};
>> +
>> +	vcc5v0_usb2: vcc5v0_usb2 {
>> +		compatible = "regulator-fixed";
>> +		regulator-name = "vcc5v0_usb2";
>> +		regulator-always-on;
>> +		regulator-boot-on;
>> +		vin-supply = <&vcc5v0_sys>;
>> +	};
>> +
>> +	/* switched by pmic_sleep */
>> +	vcc1v8_s3: vcca1v8_s3: vcc1v8-s3 {
>> +		compatible = "regulator-fixed";
>> +		regulator-name = "vcc1v8_s3";
>> +		regulator-always-on;
>> +		regulator-boot-on;
>> +		regulator-min-microvolt = <1800000>;
>> +		regulator-max-microvolt = <1800000>;
>> +		vin-supply = <&vcc_1v8>;
>> +	};
>> +
>> +	vcc3v0_sd: vcc3v0_sd {
> 
> dt-spec mandates node names with "-", so this should become
> 	vcc3v0_sd: vcc3v0-sd {
> 
> Same for most regulators above.
> 
>> +	rk808: pmic@1b {
>> +		compatible = "rockchip,rk808";
>> +		reg = <0x1b>;
>> +		interrupt-parent = <&gpio1>;
>> +		interrupts = <21 IRQ_TYPE_LEVEL_LOW>;
>> +		pinctrl-names = "default";
>> +		pinctrl-0 = <&pmic_int_l>;
>> +		rockchip,system-power-controller;
>> +		wakeup-source;
>> +		#clock-cells = <1>;
>> +		clock-output-names = "rk808-clkout1", "rk808-clkout2";
> 
> rename rk808-clkout1 to xin32k so that it hooks correctly into
> the rk3399 clock controller, as that signals is providing the 32kHz clock
> for the system. (see $debug/clk/clk_summary and rk3399-cru dt binding)
> 
> 
>> +&pinctrl {
>> +
> 
> unnecessary empty line
> 
>> +	pmic {
> 
> 
>> +&rga {
>> +	status = "okay";
>> +};
> 
> rga is not dependant on pinout, so is always enabled in rk3399.dtsi
> So this node can go away.
> 
>> +&sdhci {
>> +	bus-width = <8>;
>> +	mmc-hs400-1_8v;
>> +	supports-emmc;
> 
> remnant from the vendor-kernel?
> Should also go away.
> 
>> +	non-removable;
>> +	keep-power-in-suspend;

keep-power-in-suspend is for SDIO only.
Please remove this.

>> +	mmc-hs400-enhanced-strobe;
>> +	status = "okay";
>> +};
>> +
> 
>> +&usbdrd3_0 {
>> +	status = "okay";
>> +	extcon = <&fusb0>;
> 
> I still don't think that extcon gets defined at all and is also
> not specified in any dwc3 binding, so should probably go away.
> 
> 
> Heiko
> 
> 
> 
> _______________________________________________
> Linux-rockchip mailing list
> Linux-rockchip@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-rockchip
> 
> 
> 


  reply	other threads:[~2018-11-27  0:53 UTC|newest]

Thread overview: 9+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2018-11-23  7:26 [PATCH] arm64: dts: rockchip: Add DT for nanopc-t4 Tomeu Vizoso
2018-11-23  7:46 ` [PATCH v2] " Tomeu Vizoso
2018-11-23 12:31   ` Heiko Stuebner
2018-11-26 14:47 ` [PATCH v3] " Tomeu Vizoso
2018-11-26 23:48   ` Heiko Stuebner
2018-11-27  0:45     ` Shawn Lin [this message]
2018-11-27  9:07 ` [PATCH v4] " Tomeu Vizoso
2018-11-28  2:45   ` Robin Murphy
2018-12-07 17:56   ` Rob Herring

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=e9ee8167-c398-c14e-d798-3b4233ba2ff2@rock-chips.com \
    --to=shawn.lin@rock-chips.com \
    --cc=devicetree@vger.kernel.org \
    --cc=enric.balletbo@collabora.com \
    --cc=ezequiel@collabora.com \
    --cc=heiko@sntech.de \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-rockchip@lists.infradead.org \
    --cc=mark.rutland@arm.com \
    --cc=robh+dt@kernel.org \
    --cc=tomeu.vizoso@collabora.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).