linux-kernel.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
To: matti.vaittinen@fi.rohmeurope.com, mazziesaccount@gmail.com
Cc: Jacek Anaszewski <jacek.anaszewski@gmail.com>,
	Pavel Machek <pavel@ucw.cz>, Dan Murphy <dmurphy@ti.com>,
	Rob Herring <robh+dt@kernel.org>,
	Mark Rutland <mark.rutland@arm.com>,
	Lee Jones <lee.jones@linaro.org>,
	Liam Girdwood <lgirdwood@gmail.com>,
	Mark Brown <broonie@kernel.org>,
	Michael Turquette <mturquette@baylibre.com>,
	Stephen Boyd <sboyd@kernel.org>,
	Linus Walleij <linus.walleij@linaro.org>,
	Bartosz Golaszewski <bgolaszewski@baylibre.com>,
	Alessandro Zummo <a.zummo@towertech.it>,
	Alexandre Belloni <alexandre.belloni@bootlin.com>,
	linux-leds@vger.kernel.org, devicetree@vger.kernel.org,
	linux-kernel@vger.kernel.org, linux-clk@vger.kernel.org,
	linux-gpio@vger.kernel.org, linux-rtc@vger.kernel.org
Subject: [RFC PATCH v3 08/15] regulator: bd718x7: Split driver to common and bd718x7 specific parts
Date: Fri, 1 Nov 2019 13:41:01 +0200	[thread overview]
Message-ID: <fe80a2456524580bfa43c0e2fe26f669d5ba5e54.1572606437.git.matti.vaittinen@fi.rohmeurope.com> (raw)
In-Reply-To: <cover.1572606437.git.matti.vaittinen@fi.rohmeurope.com>

Few ROHM PMICs allow setting the voltage states for different system states
like RUN, IDLE, SUSPEND and LPSR. States are then changed via SoC specific
mechanisms. bd718x7 driver implemented device-tree parsing functions for
these state specific voltages. The parsing functions can be re-used by
other ROHM chip drivers like bd71828. Split the generic functions from
bd718x7-regulator.c to rohm-regulator.c and export them for other modules
to use.

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
---

Changes since v2 - no changes.

 drivers/regulator/Kconfig             |   4 +
 drivers/regulator/Makefile            |   1 +
 drivers/regulator/bd718x7-regulator.c | 183 ++++++++------------------
 drivers/regulator/rohm-regulator.c    |  95 +++++++++++++
 include/linux/mfd/rohm-generic.h      |  44 +++++++
 5 files changed, 199 insertions(+), 128 deletions(-)
 create mode 100644 drivers/regulator/rohm-regulator.c

diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index 3ee63531f6d5..5182a3d5660c 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -197,6 +197,7 @@ config REGULATOR_BD70528
 config REGULATOR_BD718XX
 	tristate "ROHM BD71837 Power Regulator"
 	depends on MFD_ROHM_BD718XX
+	select REGULATOR_ROHM
 	help
 	  This driver supports voltage regulators on ROHM BD71837 PMIC.
 	  This will enable support for the software controllable buck
@@ -790,6 +791,9 @@ config REGULATOR_RN5T618
 	  Say y here to support the regulators found on Ricoh RN5T567,
 	  RN5T618 or RC5T619 PMIC.
 
+config REGULATOR_ROHM
+	tristate
+
 config REGULATOR_RT5033
 	tristate "Richtek RT5033 Regulators"
 	depends on MFD_RT5033
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index 2210ba56f9bd..6bcab72c1fc7 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -99,6 +99,7 @@ obj-$(CONFIG_REGULATOR_PCF50633) += pcf50633-regulator.o
 obj-$(CONFIG_REGULATOR_RC5T583)  += rc5t583-regulator.o
 obj-$(CONFIG_REGULATOR_RK808)   += rk808-regulator.o
 obj-$(CONFIG_REGULATOR_RN5T618) += rn5t618-regulator.o
+obj-$(CONFIG_REGULATOR_ROHM)	+= rohm-regulator.o
 obj-$(CONFIG_REGULATOR_RT5033)	+= rt5033-regulator.o
 obj-$(CONFIG_REGULATOR_S2MPA01) += s2mpa01.o
 obj-$(CONFIG_REGULATOR_S2MPS11) += s2mps11.o
diff --git a/drivers/regulator/bd718x7-regulator.c b/drivers/regulator/bd718x7-regulator.c
index bdab46a5c461..2dcb010a626c 100644
--- a/drivers/regulator/bd718x7-regulator.c
+++ b/drivers/regulator/bd718x7-regulator.c
@@ -318,6 +318,7 @@ struct reg_init {
 };
 struct bd718xx_regulator_data {
 	struct regulator_desc desc;
+	const struct rohm_dvs_config dvs;
 	const struct reg_init init;
 	const struct reg_init *additional_inits;
 	int additional_init_amnt;
@@ -349,133 +350,15 @@ static const struct reg_init bd71837_ldo6_inits[] = {
 	},
 };
 
-#define NUM_DVS_BUCKS 4
-
-struct of_dvs_setting {
-	const char *prop;
-	unsigned int reg;
-};
-
-static int set_dvs_levels(const struct of_dvs_setting *dvs,
-			  struct device_node *np,
-			  const struct regulator_desc *desc,
-			  struct regmap *regmap)
-{
-	int ret, i;
-	unsigned int uv;
-
-	ret = of_property_read_u32(np, dvs->prop, &uv);
-	if (ret) {
-		if (ret != -EINVAL)
-			return ret;
-		return 0;
-	}
-
-	for (i = 0; i < desc->n_voltages; i++) {
-		ret = regulator_desc_list_voltage_linear_range(desc, i);
-		if (ret < 0)
-			continue;
-		if (ret == uv) {
-			i <<= ffs(desc->vsel_mask) - 1;
-			ret = regmap_update_bits(regmap, dvs->reg,
-						 DVS_BUCK_RUN_MASK, i);
-			break;
-		}
-	}
-	return ret;
-}
-
-static int buck4_set_hw_dvs_levels(struct device_node *np,
+static int buck_set_hw_dvs_levels(struct device_node *np,
 			    const struct regulator_desc *desc,
 			    struct regulator_config *cfg)
 {
-	int ret, i;
-	const struct of_dvs_setting dvs[] = {
-		{
-			.prop = "rohm,dvs-run-voltage",
-			.reg = BD71837_REG_BUCK4_VOLT_RUN,
-		},
-	};
+	struct bd718xx_regulator_data *data;
 
-	for (i = 0; i < ARRAY_SIZE(dvs); i++) {
-		ret = set_dvs_levels(&dvs[i], np, desc, cfg->regmap);
-		if (ret)
-			break;
-	}
-	return ret;
-}
-static int buck3_set_hw_dvs_levels(struct device_node *np,
-			    const struct regulator_desc *desc,
-			    struct regulator_config *cfg)
-{
-	int ret, i;
-	const struct of_dvs_setting dvs[] = {
-		{
-			.prop = "rohm,dvs-run-voltage",
-			.reg = BD71837_REG_BUCK3_VOLT_RUN,
-		},
-	};
+	data = container_of(desc, struct bd718xx_regulator_data, desc);
 
-	for (i = 0; i < ARRAY_SIZE(dvs); i++) {
-		ret = set_dvs_levels(&dvs[i], np, desc, cfg->regmap);
-		if (ret)
-			break;
-	}
-	return ret;
-}
-
-static int buck2_set_hw_dvs_levels(struct device_node *np,
-			    const struct regulator_desc *desc,
-			    struct regulator_config *cfg)
-{
-	int ret, i;
-	const struct of_dvs_setting dvs[] = {
-		{
-			.prop = "rohm,dvs-run-voltage",
-			.reg = BD718XX_REG_BUCK2_VOLT_RUN,
-		},
-		{
-			.prop = "rohm,dvs-idle-voltage",
-			.reg = BD718XX_REG_BUCK2_VOLT_IDLE,
-		},
-	};
-
-
-
-	for (i = 0; i < ARRAY_SIZE(dvs); i++) {
-		ret = set_dvs_levels(&dvs[i], np, desc, cfg->regmap);
-		if (ret)
-			break;
-	}
-	return ret;
-}
-
-static int buck1_set_hw_dvs_levels(struct device_node *np,
-			    const struct regulator_desc *desc,
-			    struct regulator_config *cfg)
-{
-	int ret, i;
-	const struct of_dvs_setting dvs[] = {
-		{
-			.prop = "rohm,dvs-run-voltage",
-			.reg = BD718XX_REG_BUCK1_VOLT_RUN,
-		},
-		{
-			.prop = "rohm,dvs-idle-voltage",
-			.reg = BD718XX_REG_BUCK1_VOLT_IDLE,
-		},
-		{
-			.prop = "rohm,dvs-suspend-voltage",
-			.reg = BD718XX_REG_BUCK1_VOLT_SUSP,
-		},
-	};
-
-	for (i = 0; i < ARRAY_SIZE(dvs); i++) {
-		ret = set_dvs_levels(&dvs[i], np, desc, cfg->regmap);
-		if (ret)
-			break;
-	}
-	return ret;
+	return rohm_regulator_set_dvs_levels(&data->dvs, np, desc, cfg->regmap);
 }
 
 static const struct bd718xx_regulator_data bd71847_regulators[] = {
@@ -496,7 +379,17 @@ static const struct bd718xx_regulator_data bd71847_regulators[] = {
 			.enable_reg = BD718XX_REG_BUCK1_CTRL,
 			.enable_mask = BD718XX_BUCK_EN,
 			.owner = THIS_MODULE,
-			.of_parse_cb = buck1_set_hw_dvs_levels,
+			.of_parse_cb = buck_set_hw_dvs_levels,
+		},
+		.dvs = {
+			.level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE |
+				     ROHM_DVS_LEVEL_SUSPEND,
+			.run_reg = BD718XX_REG_BUCK1_VOLT_RUN,
+			.run_mask = DVS_BUCK_RUN_MASK,
+			.idle_reg = BD718XX_REG_BUCK1_VOLT_IDLE,
+			.idle_mask = DVS_BUCK_RUN_MASK,
+			.suspend_reg = BD718XX_REG_BUCK1_VOLT_SUSP,
+			.suspend_mask = DVS_BUCK_RUN_MASK,
 		},
 		.init = {
 			.reg = BD718XX_REG_BUCK1_CTRL,
@@ -520,7 +413,14 @@ static const struct bd718xx_regulator_data bd71847_regulators[] = {
 			.enable_reg = BD718XX_REG_BUCK2_CTRL,
 			.enable_mask = BD718XX_BUCK_EN,
 			.owner = THIS_MODULE,
-			.of_parse_cb = buck2_set_hw_dvs_levels,
+			.of_parse_cb = buck_set_hw_dvs_levels,
+		},
+		.dvs = {
+			.level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE,
+			.run_reg = BD718XX_REG_BUCK2_VOLT_RUN,
+			.run_mask = DVS_BUCK_RUN_MASK,
+			.idle_reg = BD718XX_REG_BUCK2_VOLT_IDLE,
+			.idle_mask = DVS_BUCK_RUN_MASK,
 		},
 		.init = {
 			.reg = BD718XX_REG_BUCK2_CTRL,
@@ -792,7 +692,17 @@ static const struct bd718xx_regulator_data bd71837_regulators[] = {
 			.enable_reg = BD718XX_REG_BUCK1_CTRL,
 			.enable_mask = BD718XX_BUCK_EN,
 			.owner = THIS_MODULE,
-			.of_parse_cb = buck1_set_hw_dvs_levels,
+			.of_parse_cb = buck_set_hw_dvs_levels,
+		},
+		.dvs = {
+			.level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE |
+				     ROHM_DVS_LEVEL_SUSPEND,
+			.run_reg = BD718XX_REG_BUCK1_VOLT_RUN,
+			.run_mask = DVS_BUCK_RUN_MASK,
+			.idle_reg = BD718XX_REG_BUCK1_VOLT_IDLE,
+			.idle_mask = DVS_BUCK_RUN_MASK,
+			.suspend_reg = BD718XX_REG_BUCK1_VOLT_SUSP,
+			.suspend_mask = DVS_BUCK_RUN_MASK,
 		},
 		.init = {
 			.reg = BD718XX_REG_BUCK1_CTRL,
@@ -816,7 +726,14 @@ static const struct bd718xx_regulator_data bd71837_regulators[] = {
 			.enable_reg = BD718XX_REG_BUCK2_CTRL,
 			.enable_mask = BD718XX_BUCK_EN,
 			.owner = THIS_MODULE,
-			.of_parse_cb = buck2_set_hw_dvs_levels,
+			.of_parse_cb = buck_set_hw_dvs_levels,
+		},
+		.dvs = {
+			.level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE,
+			.run_reg = BD718XX_REG_BUCK2_VOLT_RUN,
+			.run_mask = DVS_BUCK_RUN_MASK,
+			.idle_reg = BD718XX_REG_BUCK2_VOLT_IDLE,
+			.idle_mask = DVS_BUCK_RUN_MASK,
 		},
 		.init = {
 			.reg = BD718XX_REG_BUCK2_CTRL,
@@ -840,7 +757,12 @@ static const struct bd718xx_regulator_data bd71837_regulators[] = {
 			.enable_reg = BD71837_REG_BUCK3_CTRL,
 			.enable_mask = BD718XX_BUCK_EN,
 			.owner = THIS_MODULE,
-			.of_parse_cb = buck3_set_hw_dvs_levels,
+			.of_parse_cb = buck_set_hw_dvs_levels,
+		},
+		.dvs = {
+			.level_map = ROHM_DVS_LEVEL_RUN,
+			.run_reg = BD71837_REG_BUCK3_VOLT_RUN,
+			.run_mask = DVS_BUCK_RUN_MASK,
 		},
 		.init = {
 			.reg = BD71837_REG_BUCK3_CTRL,
@@ -864,7 +786,12 @@ static const struct bd718xx_regulator_data bd71837_regulators[] = {
 			.enable_reg = BD71837_REG_BUCK4_CTRL,
 			.enable_mask = BD718XX_BUCK_EN,
 			.owner = THIS_MODULE,
-			.of_parse_cb = buck4_set_hw_dvs_levels,
+			.of_parse_cb = buck_set_hw_dvs_levels,
+		},
+		.dvs = {
+			.level_map = ROHM_DVS_LEVEL_RUN,
+			.run_reg = BD71837_REG_BUCK4_VOLT_RUN,
+			.run_mask = DVS_BUCK_RUN_MASK,
 		},
 		.init = {
 			.reg = BD71837_REG_BUCK4_CTRL,
diff --git a/drivers/regulator/rohm-regulator.c b/drivers/regulator/rohm-regulator.c
new file mode 100644
index 000000000000..ca368ada53c6
--- /dev/null
+++ b/drivers/regulator/rohm-regulator.c
@@ -0,0 +1,95 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2018 ROHM Semiconductors
+
+#include <linux/errno.h>
+#include <linux/mfd/rohm-generic.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/regmap.h>
+#include <linux/regulator/driver.h>
+
+static int set_dvs_level(const struct regulator_desc *desc,
+			 struct device_node *np, struct regmap *regmap,
+			 char *prop, unsigned int reg, unsigned int mask,
+			 unsigned int omask, unsigned int oreg)
+{
+	int ret, i;
+	uint32_t uv;
+
+	ret = of_property_read_u32(np, prop, &uv);
+	if (ret) {
+		if (ret != -EINVAL)
+			return ret;
+		return 0;
+	}
+
+	if (uv == 0) {
+		if (omask)
+			return regmap_update_bits(regmap, oreg, omask, 0);
+	}
+	for (i = 0; i < desc->n_voltages; i++) {
+		ret = regulator_desc_list_voltage_linear_range(desc, i);
+		if (ret < 0)
+			continue;
+		if (ret == uv) {
+			i <<= ffs(desc->vsel_mask) - 1;
+			ret = regmap_update_bits(regmap, reg, mask, i);
+			if (omask && !ret)
+				ret = regmap_update_bits(regmap, oreg, omask,
+							 omask);
+			break;
+		}
+	}
+	return ret;
+}
+
+int rohm_regulator_set_dvs_levels(const struct rohm_dvs_config *dvs,
+			  struct device_node *np,
+			  const struct regulator_desc *desc,
+			  struct regmap *regmap)
+{
+	int i, ret = 0;
+	char *prop;
+	unsigned int reg, mask, omask, oreg = desc->enable_reg;
+
+	for (i = 0; i < ROHM_DVS_LEVEL_MAX && !ret; i++) {
+		if (dvs->level_map & (1 << i)) {
+			switch (i + 1) {
+			case ROHM_DVS_LEVEL_RUN:
+				prop = "rohm,dvs-run-voltage";
+				reg = dvs->run_reg;
+				mask = dvs->run_mask;
+				omask = dvs->run_on_mask;
+				break;
+			case ROHM_DVS_LEVEL_IDLE:
+				prop = "rohm,dvs-idle-voltage";
+				reg = dvs->idle_reg;
+				mask = dvs->idle_mask;
+				omask = dvs->idle_on_mask;
+				break;
+			case ROHM_DVS_LEVEL_SUSPEND:
+				prop = "rohm,dvs-suspend-voltage";
+				reg = dvs->suspend_reg;
+				mask = dvs->suspend_mask;
+				omask = dvs->suspend_on_mask;
+				break;
+			case ROHM_DVS_LEVEL_LPSR:
+				prop = "rohm,dvs-lpsr-voltage";
+				reg = dvs->lpsr_reg;
+				mask = dvs->lpsr_mask;
+				omask = dvs->lpsr_on_mask;
+				break;
+			default:
+				return -EINVAL;
+			}
+			ret = set_dvs_level(desc, np, regmap, prop, reg, mask,
+					    omask, oreg);
+		}
+	}
+	return ret;
+}
+EXPORT_SYMBOL(rohm_regulator_set_dvs_levels);
+
+MODULE_LICENSE("GPL v2");
+MODULE_AUTHOR("Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>");
+MODULE_DESCRIPTION("Generic helpers for ROHM PMIC regulator drivers");
diff --git a/include/linux/mfd/rohm-generic.h b/include/linux/mfd/rohm-generic.h
index b280f3100d6c..86397b42e9bf 100644
--- a/include/linux/mfd/rohm-generic.h
+++ b/include/linux/mfd/rohm-generic.h
@@ -4,6 +4,9 @@
 #ifndef __LINUX_MFD_ROHM_H__
 #define __LINUX_MFD_ROHM_H__
 
+#include <linux/regmap.h>
+#include <linux/regulator/driver.h>
+
 enum {
 	ROHM_CHIP_TYPE_BD71837 = 0,
 	ROHM_CHIP_TYPE_BD71847,
@@ -18,4 +21,45 @@ struct rohm_regmap_dev {
 	struct regmap *regmap;
 };
 
+enum {
+	ROHM_DVS_LEVEL_UNKNOWN,
+	ROHM_DVS_LEVEL_RUN,
+	ROHM_DVS_LEVEL_IDLE,
+	ROHM_DVS_LEVEL_SUSPEND,
+	ROHM_DVS_LEVEL_LPSR,
+#define ROHM_DVS_LEVEL_MAX ROHM_DVS_LEVEL_LPSR
+};
+
+struct rohm_dvs_config {
+	uint64_t level_map;
+	unsigned int run_reg;
+	unsigned int run_mask;
+	unsigned int run_on_mask;
+	unsigned int idle_reg;
+	unsigned int idle_mask;
+	unsigned int idle_on_mask;
+	unsigned int suspend_reg;
+	unsigned int suspend_mask;
+	unsigned int suspend_on_mask;
+	unsigned int lpsr_reg;
+	unsigned int lpsr_mask;
+	unsigned int lpsr_on_mask;
+};
+
+#if IS_ENABLED(CONFIG_REGULATOR_ROHM)
+int rohm_regulator_set_dvs_levels(const struct rohm_dvs_config *dvs,
+				  struct device_node *np,
+				  const struct regulator_desc *desc,
+				  struct regmap *regmap);
+
+#else
+static inline int rohm_regulator_set_dvs_levels(const struct rohm_dvs_config *dvs,
+						struct device_node *np,
+						const struct regulator_desc *desc,
+						struct regmap *regmap)
+{
+	return 0;
+}
+#endif //IS_ENABLED(CONFIG_REGULATOR_ROHM)
+
 #endif
-- 
2.21.0


-- 
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND

~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =] 

  parent reply	other threads:[~2019-11-01 11:41 UTC|newest]

Thread overview: 38+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-11-01 11:28 [RFC PATCH v3 00/15] Support ROHM BD71828 PMIC Matti Vaittinen
2019-11-01 11:29 ` [RFC PATCH v3 01/15] mfd: bd71828: Support ROHM BD71828 PMIC - core Matti Vaittinen
2019-11-11 10:57   ` Lee Jones
2019-11-11 11:20     ` Vaittinen, Matti
2019-11-01 11:31 ` [RFC PATCH v3 02/15] dt-bindings: mfd: Document ROHM BD71828 bindings Matti Vaittinen
2019-11-05 20:43   ` Rob Herring
2019-11-06 12:55     ` SPAM (R/EU IT) // " Vaittinen, Matti
2019-11-01 11:31 ` [RFC PATCH v3 03/15] dt-bindings: regulator: Document ROHM BD71282 regulator bindings Matti Vaittinen
2019-11-05 20:52   ` Rob Herring
2019-11-07  6:50     ` SPAM (R/EU IT) // " Vaittinen, Matti
2019-11-01 11:32 ` [RFC PATCH v3 04/15] dt-bindings: leds: ROHM BD71282 PMIC LED driver Matti Vaittinen
2019-11-05 19:14   ` Dan Murphy
2019-11-05 20:59     ` Rob Herring
2019-11-06 13:05     ` Vaittinen, Matti
2019-11-05 20:57   ` Rob Herring
2019-11-01 11:33 ` [RFC PATCH v3 05/15] mfd: input: bd71828: Add power-key support Matti Vaittinen
2019-11-11 10:59   ` Lee Jones
2019-11-11 11:07     ` Vaittinen, Matti
2019-11-01 11:38 ` [RFC PATCH v3 06/15] clk: bd718x7: Support ROHM BD71828 clk block Matti Vaittinen
2019-11-01 11:39 ` [RFC PATCH v3 07/15] clk: bd718x7: simplify header dependencies Matti Vaittinen
2019-11-01 11:41 ` Matti Vaittinen [this message]
2019-11-01 11:42 ` [RFC PATCH v3 09/15] regulator: bd71828: Basic support for ROHM bd71828 PMIC regulators Matti Vaittinen
2019-11-01 11:43 ` [RFC PATCH v3 10/15] regulator: bd71828: Add GPIO based run-level control for regulators Matti Vaittinen
2019-11-03 22:27   ` Linus Walleij
2019-11-04  7:05     ` Vaittinen, Matti
2019-11-05 13:24       ` Linus Walleij
2019-11-05 14:07         ` Vaittinen, Matti
2019-11-01 11:44 ` [RFC PATCH v3 11/15] regulator: bd71828: enhanced run-level support Matti Vaittinen
2019-11-01 11:45 ` [RFC PATCH v3 12/15] regulator: bd71828: Support in-kernel APIs to change run-level Matti Vaittinen
2019-11-01 11:49 ` [RFC PATCH v3 13/15] rtc: bd70528 add BD71828 support Matti Vaittinen
2019-11-01 11:49 ` [RFC PATCH v3 14/15] gpio: Add definition for GPIO direction Matti Vaittinen
2019-11-03 22:30   ` Linus Walleij
2019-11-04  6:57     ` Vaittinen, Matti
2019-11-04 15:48     ` Vaittinen, Matti
2019-11-05 15:05       ` Linus Walleij
2019-11-06  6:51         ` Vaittinen, Matti
2019-11-01 11:51 ` [RFC PATCH v3 15/15] gpio: bd71828: Initial support for ROHM BD71828 PMIC GPIOs Matti Vaittinen
2019-11-01 11:53 ` [RFC PATCH v3 00/15] Support ROHM BD71828 PMIC Vaittinen, Matti

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=fe80a2456524580bfa43c0e2fe26f669d5ba5e54.1572606437.git.matti.vaittinen@fi.rohmeurope.com \
    --to=matti.vaittinen@fi.rohmeurope.com \
    --cc=a.zummo@towertech.it \
    --cc=alexandre.belloni@bootlin.com \
    --cc=bgolaszewski@baylibre.com \
    --cc=broonie@kernel.org \
    --cc=devicetree@vger.kernel.org \
    --cc=dmurphy@ti.com \
    --cc=jacek.anaszewski@gmail.com \
    --cc=lee.jones@linaro.org \
    --cc=lgirdwood@gmail.com \
    --cc=linus.walleij@linaro.org \
    --cc=linux-clk@vger.kernel.org \
    --cc=linux-gpio@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-leds@vger.kernel.org \
    --cc=linux-rtc@vger.kernel.org \
    --cc=mark.rutland@arm.com \
    --cc=mazziesaccount@gmail.com \
    --cc=mturquette@baylibre.com \
    --cc=pavel@ucw.cz \
    --cc=robh+dt@kernel.org \
    --cc=sboyd@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).