netdev.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Sathya Perla <sathya.perla@emulex.com>
To: <netdev@vger.kernel.org>
Subject: [PATCH net-next 2/6] be2net: fixup TX-rate setting code for Skyhawk-R
Date: Wed, 28 May 2014 12:01:01 +0530	[thread overview]
Message-ID: <1401258665-6238-3-git-send-email-sathya.perla@emulex.com> (raw)
In-Reply-To: <1401258665-6238-1-git-send-email-sathya.perla@emulex.com>

From: Ravikumar Nelavelli <ravikumar.nelavelli@emulex.com>

Skyhawk-R FW supports TX-rate setting only as a % value of the link
speed, set via the SET_PROFILE_CONFIG cmd.

This patch makes the necessary changes to the FW cmd descriptors to support
the above change and also introduces checks in be_set_vf_tx_rate() to allow
only discrete values (that map to % of the link-speed).

Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
---
 drivers/net/ethernet/emulex/benet/be_cmds.c |   40 +++++++++++-----
 drivers/net/ethernet/emulex/benet/be_cmds.h |   13 ++++--
 drivers/net/ethernet/emulex/benet/be_main.c |   66 ++++++++++++++++++---------
 3 files changed, 81 insertions(+), 38 deletions(-)

diff --git a/drivers/net/ethernet/emulex/benet/be_cmds.c b/drivers/net/ethernet/emulex/benet/be_cmds.c
index 476752d..216463b 100644
--- a/drivers/net/ethernet/emulex/benet/be_cmds.c
+++ b/drivers/net/ethernet/emulex/benet/be_cmds.c
@@ -3562,33 +3562,47 @@ void be_reset_nic_desc(struct be_nic_res_desc *nic)
 	nic->cq_count = 0xFFFF;
 	nic->toe_conn_count = 0xFFFF;
 	nic->eq_count = 0xFFFF;
+	nic->iface_count = 0xFFFF;
 	nic->link_param = 0xFF;
+	nic->channel_id_param = cpu_to_le16(0xF000);
 	nic->acpi_params = 0xFF;
 	nic->wol_param = 0x0F;
-	nic->bw_min = 0xFFFFFFFF;
+	nic->tunnel_iface_count = 0xFFFF;
+	nic->direct_tenant_iface_count = 0xFFFF;
 	nic->bw_max = 0xFFFFFFFF;
 }
 
-int be_cmd_config_qos(struct be_adapter *adapter, u32 bps, u8 domain)
+int be_cmd_config_qos(struct be_adapter *adapter, u32 max_rate, u16 link_speed,
+		      u8 domain)
 {
-	if (lancer_chip(adapter)) {
-		struct be_nic_res_desc nic_desc;
+	struct be_nic_res_desc nic_desc;
+	u32 bw_percent;
+	u16 version = 0;
+
+	if (BE3_chip(adapter))
+		return be_cmd_set_qos(adapter, max_rate / 10, domain);
 
-		be_reset_nic_desc(&nic_desc);
+	be_reset_nic_desc(&nic_desc);
+	nic_desc.pf_num = adapter->pf_number;
+	nic_desc.vf_num = domain;
+	if (lancer_chip(adapter)) {
 		nic_desc.hdr.desc_type = NIC_RESOURCE_DESC_TYPE_V0;
 		nic_desc.hdr.desc_len = RESOURCE_DESC_SIZE_V0;
 		nic_desc.flags = (1 << QUN_SHIFT) | (1 << IMM_SHIFT) |
 					(1 << NOSV_SHIFT);
-		nic_desc.pf_num = adapter->pf_number;
-		nic_desc.vf_num = domain;
-		nic_desc.bw_max = cpu_to_le32(bps);
-
-		return be_cmd_set_profile_config(adapter, &nic_desc,
-						 RESOURCE_DESC_SIZE_V0,
-						 0, domain);
+		nic_desc.bw_max = cpu_to_le32(max_rate / 10);
 	} else {
-		return be_cmd_set_qos(adapter, bps, domain);
+		version = 1;
+		nic_desc.hdr.desc_type = NIC_RESOURCE_DESC_TYPE_V1;
+		nic_desc.hdr.desc_len = RESOURCE_DESC_SIZE_V1;
+		nic_desc.flags = (1 << IMM_SHIFT) | (1 << NOSV_SHIFT);
+		bw_percent = max_rate ? (max_rate * 100) / link_speed : 100;
+		nic_desc.bw_max = cpu_to_le32(bw_percent);
 	}
+
+	return be_cmd_set_profile_config(adapter, &nic_desc,
+					 nic_desc.hdr.desc_len,
+					 version, domain);
 }
 
 int be_cmd_manage_iface(struct be_adapter *adapter, u32 iface, u8 op)
diff --git a/drivers/net/ethernet/emulex/benet/be_cmds.h b/drivers/net/ethernet/emulex/benet/be_cmds.h
index 228d4b6..9df9d3b 100644
--- a/drivers/net/ethernet/emulex/benet/be_cmds.h
+++ b/drivers/net/ethernet/emulex/benet/be_cmds.h
@@ -1891,16 +1891,20 @@ struct be_nic_res_desc {
 	u16 cq_count;
 	u16 toe_conn_count;
 	u16 eq_count;
-	u32 rsvd5;
+	u16 vlan_id;
+	u16 iface_count;
 	u32 cap_flags;
 	u8 link_param;
-	u8 rsvd6[3];
+	u8 rsvd6;
+	u16 channel_id_param;
 	u32 bw_min;
 	u32 bw_max;
 	u8 acpi_params;
 	u8 wol_param;
 	u16 rsvd7;
-	u32 rsvd8[7];
+	u16 tunnel_iface_count;
+	u16 direct_tenant_iface_count;
+	u32 rsvd8[6];
 } __packed;
 
 /************ Multi-Channel type ***********/
@@ -2101,7 +2105,8 @@ int be_cmd_get_seeprom_data(struct be_adapter *adapter,
 int be_cmd_set_loopback(struct be_adapter *adapter, u8 port_num,
 			u8 loopback_type, u8 enable);
 int be_cmd_get_phy_info(struct be_adapter *adapter);
-int be_cmd_config_qos(struct be_adapter *adapter, u32 bps, u8 domain);
+int be_cmd_config_qos(struct be_adapter *adapter, u32 max_rate,
+		      u16 link_speed, u8 domain);
 void be_detect_error(struct be_adapter *adapter);
 int be_cmd_get_die_temperature(struct be_adapter *adapter);
 int be_cmd_get_cntl_attributes(struct be_adapter *adapter);
diff --git a/drivers/net/ethernet/emulex/benet/be_main.c b/drivers/net/ethernet/emulex/benet/be_main.c
index 9116d5e..d39a1c6 100644
--- a/drivers/net/ethernet/emulex/benet/be_main.c
+++ b/drivers/net/ethernet/emulex/benet/be_main.c
@@ -1352,7 +1352,10 @@ static int be_set_vf_tx_rate(struct net_device *netdev, int vf,
 			     int min_tx_rate, int max_tx_rate)
 {
 	struct be_adapter *adapter = netdev_priv(netdev);
-	int status = 0;
+	struct device *dev = &adapter->pdev->dev;
+	int percent_rate, status = 0;
+	u16 link_speed = 0;
+	u8 link_status;
 
 	if (!sriov_enabled(adapter))
 		return -EPERM;
@@ -1363,18 +1366,47 @@ static int be_set_vf_tx_rate(struct net_device *netdev, int vf,
 	if (min_tx_rate)
 		return -EINVAL;
 
-	if (max_tx_rate < 100 || max_tx_rate > 10000) {
-		dev_err(&adapter->pdev->dev,
-			"max tx rate must be between 100 and 10000 Mbps\n");
-		return -EINVAL;
+	if (!max_tx_rate)
+		goto config_qos;
+
+	status = be_cmd_link_status_query(adapter, &link_speed,
+					  &link_status, 0);
+	if (status)
+		goto err;
+
+	if (!link_status) {
+		dev_err(dev, "TX-rate setting not allowed when link is down\n");
+		status = -EPERM;
+		goto err;
+	}
+
+	if (max_tx_rate < 100 || max_tx_rate > link_speed) {
+		dev_err(dev, "TX-rate must be between 100 and %d Mbps\n",
+			link_speed);
+		status = -EINVAL;
+		goto err;
 	}
 
-	status = be_cmd_config_qos(adapter, max_tx_rate / 10, vf + 1);
+	/* On Skyhawk the QOS setting must be done only as a % value */
+	percent_rate = link_speed / 100;
+	if (skyhawk_chip(adapter) && (max_tx_rate % percent_rate)) {
+		dev_err(dev, "TX-rate must be a multiple of %d Mbps\n",
+			percent_rate);
+		status = -EINVAL;
+		goto err;
+	}
+
+config_qos:
+	status = be_cmd_config_qos(adapter, max_tx_rate, link_speed, vf + 1);
 	if (status)
-		dev_err(&adapter->pdev->dev,
-			"max tx rate %d on VF %d failed\n", max_tx_rate, vf);
-	else
-		adapter->vf_cfg[vf].tx_rate = max_tx_rate;
+		goto err;
+
+	adapter->vf_cfg[vf].tx_rate = max_tx_rate;
+	return 0;
+
+err:
+	dev_err(dev, "TX-rate setting of %dMbps on VF%d failed\n",
+		max_tx_rate, vf);
 	return status;
 }
 static int be_set_vf_link_state(struct net_device *netdev, int vf,
@@ -3135,7 +3167,6 @@ static int be_vf_setup(struct be_adapter *adapter)
 	struct be_vf_cfg *vf_cfg;
 	int status, old_vfs, vf;
 	u32 privileges;
-	u16 lnk_speed;
 
 	old_vfs = pci_num_vf(adapter->pdev);
 	if (old_vfs) {
@@ -3191,16 +3222,9 @@ static int be_vf_setup(struct be_adapter *adapter)
 					 vf);
 		}
 
-		/* BE3 FW, by default, caps VF TX-rate to 100mbps.
-		 * Allow full available bandwidth
-		 */
-		if (BE3_chip(adapter) && !old_vfs)
-			be_cmd_config_qos(adapter, 1000, vf + 1);
-
-		status = be_cmd_link_status_query(adapter, &lnk_speed,
-						  NULL, vf + 1);
-		if (!status)
-			vf_cfg->tx_rate = lnk_speed;
+		/* Allow full available bandwidth */
+		if (!old_vfs)
+			be_cmd_config_qos(adapter, 0, 0, vf + 1);
 
 		if (!old_vfs) {
 			be_cmd_enable_vf(adapter, vf + 1);
-- 
1.7.1

  parent reply	other threads:[~2014-05-28  6:28 UTC|newest]

Thread overview: 9+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2014-05-28  6:30 [PATCH net-next 0/6] be2net: patch set Sathya Perla
2014-05-28  6:31 ` [PATCH net-next 1/6] be2net: skip multicast promiscuos setting in already set Sathya Perla
2014-05-28  6:31 ` Sathya Perla [this message]
2014-05-28  6:31 ` [PATCH net-next 3/6] be2net: support flashing new regions on Skyhawk-R Sathya Perla
2014-05-28  6:31 ` [PATCH net-next 4/6] be2net: re-factor MCCQ error status handling code Sathya Perla
2014-05-28  6:31 ` [PATCH net-next 5/6] be2net: move async cmd processing to a separate routine Sathya Perla
2014-05-30  9:18   ` Sathya Perla
2014-05-28  6:31 ` [PATCH net-next 6/6] be2net: cleanup MCC async event processing code Sathya Perla
2014-05-31  0:28 ` [PATCH net-next 0/6] be2net: patch set David Miller

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1401258665-6238-3-git-send-email-sathya.perla@emulex.com \
    --to=sathya.perla@emulex.com \
    --cc=netdev@vger.kernel.org \
    --subject='Re: [PATCH net-next 2/6] be2net: fixup TX-rate setting code for Skyhawk-R' \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).