* [PATCH net-next v2 0/2] mv88e6xxx DSA suspend to RAM support
@ 2019-01-25 9:55 Miquel Raynal
2019-01-25 9:55 ` [PATCH net-next v2 1/2] net: dsa: mv88e6xxx: Save switch rules Miquel Raynal
` (2 more replies)
0 siblings, 3 replies; 20+ messages in thread
From: Miquel Raynal @ 2019-01-25 9:55 UTC (permalink / raw)
To: Andrew Lunn, Vivien Didelot, Florian Fainelli, David S. Miller
Cc: netdev, linux-kernel, Thomas Petazzoni, Gregory Clement,
Antoine Tenart, Maxime Chevallier, Nadav Haklai, Miquel Raynal
After a first attempt of bringing S2RAM support to the DSA switch, it
has been reported that a part of the configuration was lost during the
cycle. This second version adds a first patch that saves the rules in
a per-chip list when they are applied, so that in the second patch we
bring S2RAM support by also re-applying these rules.
Bridging is set up on the EspressoBin with the below commands (thanks
to Andrew):
ip link set eth0 up
ip link add name br0 type bridge
ip link set br0 up
ip link set lan0 up
ip link set lan0 master br0
ip link set lan1 up
ip link set lan1 master br0
Static forwarding entries are added:
bridge fdb add 00:42:42:42:42:42 dev lan0
bridge fdb add 00:24:24:24:24:24 dev lan1
Dumping the switch entries gives:
# bridge fdb show
33:33:00:00:00:01 dev eth0 self permanent
01:00:5e:00:00:01 dev eth0 self permanent
33:33:ff:06:e2:95 dev eth0 self permanent
dc:0b:34:87:7f:27 dev lan0 br0
d4:81:d7:4f:a1:0d dev lan0 br0
f0:ad:4e:06:e2:95 dev lan0 vlan 1 br0 permanent
f0:ad:4e:06:e2:95 dev lan0 br0 permanent
00:42:42:42:42:42 dev lan0 self static
d4:81:d7:4f:a1:0d dev lan0 self
dc:0b:34:87:7f:27 dev lan0 self
00:0a:35:00:01:22 dev lan1 br0
00:0a:35:00:01:22 dev lan1 self
00:24:24:24:24:24 dev lan1 self static
33:33:00:00:00:01 dev br0 self permanent
01:00:5e:00:00:01 dev br0 self permanent
33:33:ff:00:2a:68 dev br0 self permanent
After a S2RAM cycle, the bridge and the static entries have been restored.
mv88e6085 d0032004.mdio-mii:01 lan0: configuring for phy/ link mode
mv88e6085 d0032004.mdio-mii:01 lan1: configuring for phy/ link mode
mv88e6085 d0032004.mdio-mii:01 lan1: Link is Up - 1Gbps/Full - flow control rx/tx
mv88e6085 d0032004.mdio-mii:01 lan0: Link is Up - 1Gbps/Full - flow control rx/tx
# bridge fdb show
33:33:00:00:00:01 dev eth0 self permanent
01:00:5e:00:00:01 dev eth0 self permanent
33:33:ff:06:e2:95 dev eth0 self permanent
9c:93:4e:26:e4:54 dev lan0 br0
d4:81:d7:45:de:60 dev lan0 br0
dc:0b:34:87:7f:27 dev lan0 br0
d4:81:d7:4f:a1:0d dev lan0 br0
f0:ad:4e:06:e2:95 dev lan0 vlan 1 br0 permanent
f0:ad:4e:06:e2:95 dev lan0 br0 permanent
00:42:42:42:42:42 dev lan0 self static
d4:81:d7:4f:a1:0d dev lan0 self
00:0a:35:00:01:22 dev lan1 br0
00:0a:35:00:01:22 dev lan1 self
00:24:24:24:24:24 dev lan1 self static
33:33:00:00:00:01 dev br0 self permanent
01:00:5e:00:00:01 dev br0 self permanent
33:33:ff:00:2a:68 dev br0 self permanent
An iperf test running over the whole cycle gives:
1.00-2.00 sec 81.7 MBytes 685 Mbits/sec
2.00-3.00 sec 81.8 MBytes 687 Mbits/sec
3.00-4.00 sec 81.8 MBytes 685 Mbits/sec
4.00-5.00 sec 81.7 MBytes 686 Mbits/sec
5.00-6.00 sec 81.5 MBytes 683 Mbits/sec
6.00-7.00 sec 81.6 MBytes 685 Mbits/sec
7.00-8.00 sec 81.5 MBytes 684 Mbits/sec
8.00-9.00 sec 81.7 MBytes 685 Mbits/sec
9.00-10.00 sec 81.5 MBytes 684 Mbits/sec
10.00-11.00 sec 81.6 MBytes 684 Mbits/sec
11.00-12.00 sec 81.5 MBytes 683 Mbits/sec
macb e000b000.ethernet eth0: link down
12.00-13.00 sec 19.5 MBytes 164 Mbits/sec
13.00-14.00 sec 0.00 Bytes 0.00 bits/sec
14.00-15.00 sec 0.00 Bytes 0.00 bits/sec
15.00-16.00 sec 0.00 Bytes 0.00 bits/sec
16.00-17.00 sec 0.00 Bytes 0.00 bits/sec
17.00-18.00 sec 0.00 Bytes 0.00 bits/sec
18.00-19.00 sec 0.00 Bytes 0.00 bits/sec
19.00-20.00 sec 0.00 Bytes 0.00 bits/sec
20.00-21.00 sec 0.00 Bytes 0.00 bits/sec
21.00-22.00 sec 0.00 Bytes 0.00 bits/sec
22.00-23.00 sec 0.00 Bytes 0.00 bits/sec
macb e000b000.ethernet eth0: link up (1000/Full)
23.00-24.00 sec 0.00 Bytes 0.00 bits/sec
24.00-25.00 sec 0.00 Bytes 0.00 bits/sec
25.00-26.00 sec 18.6 MBytes 156 Mbits/sec
26.00-27.00 sec 81.5 MBytes 684 Mbits/sec
27.00-28.00 sec 81.6 MBytes 684 Mbits/sec
28.00-29.00 sec 81.5 MBytes 684 Mbits/sec
29.00-30.00 sec 81.5 MBytes 683 Mbits/sec
30.00-31.00 sec 81.6 MBytes 685 Mbits/sec
31.00-32.00 sec 81.6 MBytes 684 Mbits/sec
32.00-33.00 sec 81.4 MBytes 683 Mbits/sec
33.00-34.00 sec 81.4 MBytes 683 Mbits/sec
33.00-34.00 sec 81.4 MBytes 683 Mbits/sec
I hope everything has been restored correctly, please let me know if
you spot anything else that is missing.
Thanks,
Miquèl
Miquel Raynal (2):
net: dsa: mv88e6xxx: Save switch rules
net: dsa: mv88e6xxx: Add suspend to RAM support
drivers/net/dsa/mv88e6xxx/chip.c | 359 ++++++++++++++++++++++++++++---
drivers/net/dsa/mv88e6xxx/chip.h | 33 +++
2 files changed, 357 insertions(+), 35 deletions(-)
--
2.19.1
^ permalink raw reply [flat|nested] 20+ messages in thread* [PATCH net-next v2 1/2] net: dsa: mv88e6xxx: Save switch rules 2019-01-25 9:55 [PATCH net-next v2 0/2] mv88e6xxx DSA suspend to RAM support Miquel Raynal @ 2019-01-25 9:55 ` Miquel Raynal 2019-01-25 18:37 ` Florian Fainelli 2019-01-25 9:55 ` [PATCH net-next v2 2/2] net: dsa: mv88e6xxx: Add suspend to RAM support Miquel Raynal 2019-01-27 21:22 ` [PATCH net-next v2 0/2] mv88e6xxx DSA " David Miller 2 siblings, 1 reply; 20+ messages in thread From: Miquel Raynal @ 2019-01-25 9:55 UTC (permalink / raw) To: Andrew Lunn, Vivien Didelot, Florian Fainelli, David S. Miller Cc: netdev, linux-kernel, Thomas Petazzoni, Gregory Clement, Antoine Tenart, Maxime Chevallier, Nadav Haklai, Miquel Raynal The user might apply a specific switch configuration, with specific forwarding rules, VLAN, bridges, etc. During suspend to RAM the switch power will be turned off and the switch will lost its configuration. In an attempt to bring S2RAM support to the mv88e6xxx DSA, let's first save these rules in a per-chip list thanks to the mv88e6xxx_add/del_xxx_rule() helpers. These helpers are then called from various callbacks: * mv88e6xxx_port_fdb_add/del() * mv88e6xxx_port_mdb_add/del() * mv88e6xxx_port_vlan_add/del() * mv88e6xxx_port_bridge_join/leave() * mv88e6xxx_crosschip_bridge_join/leave() To avoid recursion problems when replaying the rules, the content of the above *_add()/*_join() callbacks has been moved in separate helpers with a '_' prefix. Hence, each callback just calls the corresponding helper and the corresponding *_add_xxx_rule(). Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> --- Changes since v1: ================= * New patch: saves the forwarding/vlan/bridge rules when they are applied in a list. This way in the second patch when adding S2RAM support, we just need to replay these rules. drivers/net/dsa/mv88e6xxx/chip.c | 270 +++++++++++++++++++++++++++---- drivers/net/dsa/mv88e6xxx/chip.h | 33 ++++ 2 files changed, 271 insertions(+), 32 deletions(-) diff --git a/drivers/net/dsa/mv88e6xxx/chip.c b/drivers/net/dsa/mv88e6xxx/chip.c index 8a517d8fb9d1..428177f80abd 100644 --- a/drivers/net/dsa/mv88e6xxx/chip.c +++ b/drivers/net/dsa/mv88e6xxx/chip.c @@ -52,6 +52,111 @@ static void assert_reg_lock(struct mv88e6xxx_chip *chip) } } +static void mv88e6xxx_add_rule(struct mv88e6xxx_chip *chip, int port, + enum mv88e6xxx_rule_type type, + const unsigned char *addr, u16 vid, + const struct switchdev_obj_port_vlan *vlan, + int dev, struct net_device *br) +{ + struct mv88e6xxx_rule *rule; + + rule = kzalloc(sizeof(*rule), GFP_KERNEL); + if (!rule) + return; + + rule->port = port; + rule->type = type; + switch (type) { + case FDB_RULE: + case MDB_RULE: + ether_addr_copy(rule->params.db.addr, addr); + rule->params.db.vid = vid; + break; + case VLAN_RULE: + rule->params.vlan = *vlan; + break; + case BRIDGE_RULE: + rule->params.br = br; + break; + case CC_BRIDGE_RULE: + rule->params.crosschip.dev = dev; + rule->params.crosschip.br = br; + break; + } + + list_add_tail(&rule->node, &chip->rules); +} + +static void mv88e6xxx_del_rule(struct mv88e6xxx_chip *chip, int port, + enum mv88e6xxx_rule_type type, + const unsigned char *addr, u16 vid, + const struct switchdev_obj_port_vlan *vlan, + int dev, struct net_device *br) +{ + struct mv88e6xxx_rule *rule, *next; + + list_for_each_entry_safe(rule, next, &chip->rules, node) { + if (rule->port != port || rule->type != type) + continue; + + switch (type) { + case FDB_RULE: + case MDB_RULE: + if (!memcmp(rule->params.db.addr, addr, ETH_ALEN) && + rule->params.db.vid == vid) + goto found; + break; + case VLAN_RULE: + if (rule->params.vlan.flags == vlan->flags && + rule->params.vlan.vid_begin == vlan->vid_begin && + rule->params.vlan.vid_end == vlan->vid_end) + goto found; + break; + case BRIDGE_RULE: + if (rule->params.br == br) + goto found; + break; + case CC_BRIDGE_RULE: + if (rule->params.crosschip.br == br && + rule->params.crosschip.dev == dev) + goto found; + break; + default: + dev_warn(chip->dev, "Unknown rule type\n"); + break; + } + } + + dev_info(chip->dev, "Cannot delete rule: not found\n"); + + return; + +found: + list_del(&rule->node); + kfree(rule); +} + +#define mv88e6xxx_add_fdb_rule(chip, port, addr, vid) \ + mv88e6xxx_add_rule(chip, port, FDB_RULE, addr, vid, NULL, 0, NULL) +#define mv88e6xxx_del_fdb_rule(chip, port, addr, vid) \ + mv88e6xxx_del_rule(chip, port, FDB_RULE, addr, vid, NULL, 0, NULL) +#define mv88e6xxx_add_mdb_rule(chip, port, addr, vid) \ + mv88e6xxx_add_rule(chip, port, MDB_RULE, addr, vid, NULL, 0, NULL) +#define mv88e6xxx_del_mdb_rule(chip, port, addr, vid) \ + mv88e6xxx_del_rule(chip, port, MDB_RULE, addr, vid, NULL, 0, NULL) +#define mv88e6xxx_add_vlan_rule(chip, port, vlan) \ + mv88e6xxx_add_rule(chip, port, VLAN_RULE, NULL, 0, vlan, 0, NULL) +#define mv88e6xxx_del_vlan_rule(chip, port, vlan) \ + mv88e6xxx_del_rule(chip, port, VLAN_RULE, NULL, 0, vlan, 0, NULL) +#define mv88e6xxx_add_bridge_rule(chip, port, br) \ + mv88e6xxx_add_rule(chip, port, BRIDGE_RULE, NULL, 0, NULL, 0, br) +#define mv88e6xxx_del_bridge_rule(chip, port, br) \ + mv88e6xxx_del_rule(chip, port, BRIDGE_RULE, NULL, 0, NULL, 0, br) +#define mv88e6xxx_add_cc_bridge_rule(chip, port, dev, br) \ + mv88e6xxx_add_rule(chip, port, CC_BRIDGE_RULE, NULL, 0, NULL, dev, br) +#define mv88e6xxx_del_cc_bridge_rule(chip, port, dev, br) \ + mv88e6xxx_del_rule(chip, port, CC_BRIDGE_RULE, NULL, 0, NULL, dev, br) + /* The switch ADDR[4:1] configuration pins define the chip SMI device address * (ADDR[0] is always zero, thus only even SMI addresses can be strapped). * @@ -1674,8 +1779,8 @@ static int mv88e6xxx_broadcast_setup(struct mv88e6xxx_chip *chip, u16 vid) return 0; } -static int _mv88e6xxx_port_vlan_add(struct mv88e6xxx_chip *chip, int port, - u16 vid, u8 member) +static int __mv88e6xxx_port_vlan_add(struct mv88e6xxx_chip *chip, int port, + u16 vid, u8 member) { struct mv88e6xxx_vtu_entry vlan; int err; @@ -1693,19 +1798,19 @@ static int _mv88e6xxx_port_vlan_add(struct mv88e6xxx_chip *chip, int port, return mv88e6xxx_broadcast_setup(chip, vid); } -static void mv88e6xxx_port_vlan_add(struct dsa_switch *ds, int port, +static int _mv88e6xxx_port_vlan_add(struct mv88e6xxx_chip *chip, int port, const struct switchdev_obj_port_vlan *vlan) { - struct mv88e6xxx_chip *chip = ds->priv; bool untagged = vlan->flags & BRIDGE_VLAN_INFO_UNTAGGED; bool pvid = vlan->flags & BRIDGE_VLAN_INFO_PVID; u8 member; u16 vid; + int err; if (!chip->info->max_vid) - return; + return -EINVAL; - if (dsa_is_dsa_port(ds, port) || dsa_is_cpu_port(ds, port)) + if (dsa_is_dsa_port(chip->ds, port) || dsa_is_cpu_port(chip->ds, port)) member = MV88E6XXX_G1_VTU_DATA_MEMBER_TAG_UNMODIFIED; else if (untagged) member = MV88E6XXX_G1_VTU_DATA_MEMBER_TAG_UNTAGGED; @@ -1714,16 +1819,37 @@ static void mv88e6xxx_port_vlan_add(struct dsa_switch *ds, int port, mutex_lock(&chip->reg_lock); - for (vid = vlan->vid_begin; vid <= vlan->vid_end; ++vid) - if (_mv88e6xxx_port_vlan_add(chip, port, vid, member)) - dev_err(ds->dev, "p%d: failed to add VLAN %d%c\n", port, - vid, untagged ? 'u' : 't'); + for (vid = vlan->vid_begin; vid <= vlan->vid_end; ++vid) { + err = __mv88e6xxx_port_vlan_add(chip, port, vid, member); + if (err) { + dev_err(chip->dev, "p%d: failed to add VLAN %d%c\n", + port, vid, untagged ? 'u' : 't'); + goto out; + } + } - if (pvid && mv88e6xxx_port_set_pvid(chip, port, vlan->vid_end)) - dev_err(ds->dev, "p%d: failed to set PVID %d\n", port, - vlan->vid_end); + if (pvid) { + err = mv88e6xxx_port_set_pvid(chip, port, vlan->vid_end); + if (err) + dev_err(chip->dev, "p%d: failed to set PVID %d\n", + port, vlan->vid_end); + } +out: mutex_unlock(&chip->reg_lock); + + return err; +} + +static void mv88e6xxx_port_vlan_add(struct dsa_switch *ds, int port, + const struct switchdev_obj_port_vlan *vlan) +{ + struct mv88e6xxx_chip *chip = ds->priv; + + if (_mv88e6xxx_port_vlan_add(chip, port, vlan)) + return; + + mv88e6xxx_add_vlan_rule(chip, port, vlan); } static int _mv88e6xxx_port_vlan_del(struct mv88e6xxx_chip *chip, @@ -1769,6 +1895,8 @@ static int mv88e6xxx_port_vlan_del(struct dsa_switch *ds, int port, if (!chip->info->max_vid) return -EOPNOTSUPP; + mv88e6xxx_del_vlan_rule(chip, port, vlan); + mutex_lock(&chip->reg_lock); err = mv88e6xxx_port_get_pvid(chip, port, &pvid); @@ -1793,10 +1921,9 @@ static int mv88e6xxx_port_vlan_del(struct dsa_switch *ds, int port, return err; } -static int mv88e6xxx_port_fdb_add(struct dsa_switch *ds, int port, - const unsigned char *addr, u16 vid) +static int _mv88e6xxx_port_fdb_add(struct mv88e6xxx_chip *chip, int port, + const unsigned char *addr, u16 vid) { - struct mv88e6xxx_chip *chip = ds->priv; int err; mutex_lock(&chip->reg_lock); @@ -1807,12 +1934,29 @@ static int mv88e6xxx_port_fdb_add(struct dsa_switch *ds, int port, return err; } +static int mv88e6xxx_port_fdb_add(struct dsa_switch *ds, int port, + const unsigned char *addr, u16 vid) +{ + struct mv88e6xxx_chip *chip = ds->priv; + int err; + + err = _mv88e6xxx_port_fdb_add(chip, port, addr, vid); + if (err) + return err; + + mv88e6xxx_add_fdb_rule(chip, port, addr, vid); + + return 0; +} + static int mv88e6xxx_port_fdb_del(struct dsa_switch *ds, int port, const unsigned char *addr, u16 vid) { struct mv88e6xxx_chip *chip = ds->priv; int err; + mv88e6xxx_del_fdb_rule(chip, port, addr, vid); + mutex_lock(&chip->reg_lock); err = mv88e6xxx_port_db_load_purge(chip, port, addr, vid, MV88E6XXX_G1_ATU_DATA_STATE_UNUSED); @@ -1945,31 +2089,68 @@ static int mv88e6xxx_bridge_map(struct mv88e6xxx_chip *chip, return 0; } +static int _mv88e6xxx_port_bridge_join(struct mv88e6xxx_chip *chip, int port, + struct net_device *br) +{ + int err; + + mutex_lock(&chip->reg_lock); + err = mv88e6xxx_bridge_map(chip, br); + mutex_unlock(&chip->reg_lock); + + return err; +} + static int mv88e6xxx_port_bridge_join(struct dsa_switch *ds, int port, struct net_device *br) { struct mv88e6xxx_chip *chip = ds->priv; int err; - mutex_lock(&chip->reg_lock); - err = mv88e6xxx_bridge_map(chip, br); - mutex_unlock(&chip->reg_lock); + err = _mv88e6xxx_port_bridge_join(chip, port, br); + if (err) + return err; - return err; + mv88e6xxx_add_bridge_rule(chip, port, br); + + return 0; } static void mv88e6xxx_port_bridge_leave(struct dsa_switch *ds, int port, struct net_device *br) { struct mv88e6xxx_chip *chip = ds->priv; + int err; + + mv88e6xxx_del_bridge_rule(chip, port, br); mutex_lock(&chip->reg_lock); - if (mv88e6xxx_bridge_map(chip, br) || - mv88e6xxx_port_vlan_map(chip, port)) + err = mv88e6xxx_bridge_map(chip, br); + if (!err) + err = mv88e6xxx_port_vlan_map(chip, port); + + if (err) dev_err(ds->dev, "failed to remap in-chip Port VLAN\n"); + mutex_unlock(&chip->reg_lock); } +static int _mv88e6xxx_crosschip_bridge_join(struct mv88e6xxx_chip *chip, + int dev, int port, + struct net_device *br) +{ + int err; + + if (!mv88e6xxx_has_pvt(chip)) + return 0; + + mutex_lock(&chip->reg_lock); + err = mv88e6xxx_pvt_map(chip, dev, port); + mutex_unlock(&chip->reg_lock); + + return err; +} + static int mv88e6xxx_crosschip_bridge_join(struct dsa_switch *ds, int dev, int port, struct net_device *br) { @@ -1979,11 +2160,13 @@ static int mv88e6xxx_crosschip_bridge_join(struct dsa_switch *ds, int dev, if (!mv88e6xxx_has_pvt(chip)) return 0; - mutex_lock(&chip->reg_lock); - err = mv88e6xxx_pvt_map(chip, dev, port); - mutex_unlock(&chip->reg_lock); + err = _mv88e6xxx_crosschip_bridge_join(chip, dev, port, br); + if (err) + return err; - return err; + mv88e6xxx_add_cc_bridge_rule(chip, port, dev, br); + + return 0; } static void mv88e6xxx_crosschip_bridge_leave(struct dsa_switch *ds, int dev, @@ -1994,6 +2177,8 @@ static void mv88e6xxx_crosschip_bridge_leave(struct dsa_switch *ds, int dev, if (!mv88e6xxx_has_pvt(chip)) return; + mv88e6xxx_del_cc_bridge_rule(chip, port, dev, br); + mutex_lock(&chip->reg_lock); if (mv88e6xxx_pvt_map(chip, dev, port)) dev_err(ds->dev, "failed to remap cross-chip Port VLAN\n"); @@ -4534,17 +4719,34 @@ static int mv88e6xxx_port_mdb_prepare(struct dsa_switch *ds, int port, return 0; } +static int _mv88e6xxx_port_mdb_add(struct mv88e6xxx_chip *chip, int port, + const unsigned char *addr, u16 vid) +{ + int err; + + mutex_lock(&chip->reg_lock); + err = mv88e6xxx_port_db_load_purge(chip, port, addr, vid, + MV88E6XXX_G1_ATU_DATA_STATE_MC_STATIC); + mutex_unlock(&chip->reg_lock); + + if (err) + dev_err(chip->dev, + "p%d: failed to load multicast MAC address\n", port); + + return err; +} + static void mv88e6xxx_port_mdb_add(struct dsa_switch *ds, int port, const struct switchdev_obj_port_mdb *mdb) { struct mv88e6xxx_chip *chip = ds->priv; + int err; - mutex_lock(&chip->reg_lock); - if (mv88e6xxx_port_db_load_purge(chip, port, mdb->addr, mdb->vid, - MV88E6XXX_G1_ATU_DATA_STATE_MC_STATIC)) - dev_err(ds->dev, "p%d: failed to load multicast MAC address\n", - port); - mutex_unlock(&chip->reg_lock); + err = _mv88e6xxx_port_mdb_add(chip, port, mdb->addr, mdb->vid); + if (err) + return; + + mv88e6xxx_add_mdb_rule(chip, port, mdb->addr, mdb->vid); } static int mv88e6xxx_port_mdb_del(struct dsa_switch *ds, int port, @@ -4553,6 +4755,8 @@ static int mv88e6xxx_port_mdb_del(struct dsa_switch *ds, int port, struct mv88e6xxx_chip *chip = ds->priv; int err; + mv88e6xxx_del_mdb_rule(chip, port, mdb->addr, mdb->vid); + mutex_lock(&chip->reg_lock); err = mv88e6xxx_port_db_load_purge(chip, port, mdb->addr, mdb->vid, MV88E6XXX_G1_ATU_DATA_STATE_UNUSED); @@ -4766,6 +4970,8 @@ static int mv88e6xxx_probe(struct mdio_device *mdiodev) if (err) goto out_mdio; + INIT_LIST_HEAD(&chip->rules); + return 0; out_mdio: diff --git a/drivers/net/dsa/mv88e6xxx/chip.h b/drivers/net/dsa/mv88e6xxx/chip.h index f9ecb7872d32..b5c8d6a8d9e7 100644 --- a/drivers/net/dsa/mv88e6xxx/chip.h +++ b/drivers/net/dsa/mv88e6xxx/chip.h @@ -203,6 +203,36 @@ struct mv88e6xxx_port { int serdes_irq; }; +enum mv88e6xxx_rule_type { + FDB_RULE, + MDB_RULE, + VLAN_RULE, + BRIDGE_RULE, + CC_BRIDGE_RULE, +}; + +struct mv88e6xxx_db_rule { + u8 addr[ETH_ALEN]; + u16 vid; +}; + +struct mv88e6xxx_br_rule { + int dev; + struct net_device *br; +}; + +struct mv88e6xxx_rule { + int port; + enum mv88e6xxx_rule_type type; + union { + struct mv88e6xxx_db_rule db; + struct switchdev_obj_port_vlan vlan; + struct net_device *br; + struct mv88e6xxx_br_rule crosschip; + } params; + struct list_head node; +}; + struct mv88e6xxx_chip { const struct mv88e6xxx_info *info; @@ -285,6 +315,9 @@ struct mv88e6xxx_chip { /* Array of port structures. */ struct mv88e6xxx_port ports[DSA_MAX_PORTS]; + + /* List of bridging rules to recover at resume */ + struct list_head rules; }; struct mv88e6xxx_bus_ops { -- 2.19.1 ^ permalink raw reply related [flat|nested] 20+ messages in thread
* Re: [PATCH net-next v2 1/2] net: dsa: mv88e6xxx: Save switch rules 2019-01-25 9:55 ` [PATCH net-next v2 1/2] net: dsa: mv88e6xxx: Save switch rules Miquel Raynal @ 2019-01-25 18:37 ` Florian Fainelli 2019-01-28 14:24 ` Miquel Raynal 0 siblings, 1 reply; 20+ messages in thread From: Florian Fainelli @ 2019-01-25 18:37 UTC (permalink / raw) To: Miquel Raynal, Andrew Lunn, Vivien Didelot, David S. Miller Cc: netdev, linux-kernel, Thomas Petazzoni, Gregory Clement, Antoine Tenart, Maxime Chevallier, Nadav Haklai Hi Miquel, On 1/25/19 1:55 AM, Miquel Raynal wrote: > The user might apply a specific switch configuration, with specific > forwarding rules, VLAN, bridges, etc. > > During suspend to RAM the switch power will be turned off and the > switch will lost its configuration. In an attempt to bring S2RAM > support to the mv88e6xxx DSA, let's first save these rules in a > per-chip list thanks to the mv88e6xxx_add/del_xxx_rule() > helpers. These helpers are then called from various callbacks: > * mv88e6xxx_port_fdb_add/del() > * mv88e6xxx_port_mdb_add/del() > * mv88e6xxx_port_vlan_add/del() > * mv88e6xxx_port_bridge_join/leave() > * mv88e6xxx_crosschip_bridge_join/leave() > > To avoid recursion problems when replaying the rules, the content of > the above *_add()/*_join() callbacks has been moved in separate > helpers with a '_' prefix. Hence, each callback just calls the > corresponding helper and the corresponding *_add_xxx_rule(). None of this should be done in the driver IMHO, because this is presumably applicable to all switch devices that lose their state during suspend/resume, so at best, this should be moved to the core DSA layer, but doing this means that we should also have a well established contract between the DSA layer and individual switch drivers as far as quiescing/saving/restoring state goes. By moving things to the core we can also more tightly control what data structures get used to represent e.g.: VLANs, FDBs, MDBs etc and possibly push/utilize caching into the original subsystem. For instance VLAN/bridge already do maintain caches of VLANs, so if we could somehow expose those, we would not bloat the kernel's memory footprint by having an additional layer to maintain with identical information. Just my 2 cents. -- Florian ^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [PATCH net-next v2 1/2] net: dsa: mv88e6xxx: Save switch rules 2019-01-25 18:37 ` Florian Fainelli @ 2019-01-28 14:24 ` Miquel Raynal 2019-01-28 14:44 ` Andrew Lunn 0 siblings, 1 reply; 20+ messages in thread From: Miquel Raynal @ 2019-01-28 14:24 UTC (permalink / raw) To: Florian Fainelli Cc: Andrew Lunn, Vivien Didelot, David S. Miller, netdev, linux-kernel, Thomas Petazzoni, Gregory Clement, Antoine Tenart, Maxime Chevallier, Nadav Haklai Hi Florian, Florian Fainelli <f.fainelli@gmail.com> wrote on Fri, 25 Jan 2019 10:37:38 -0800: > Hi Miquel, > > On 1/25/19 1:55 AM, Miquel Raynal wrote: > > The user might apply a specific switch configuration, with specific > > forwarding rules, VLAN, bridges, etc. > > > > During suspend to RAM the switch power will be turned off and the > > switch will lost its configuration. In an attempt to bring S2RAM > > support to the mv88e6xxx DSA, let's first save these rules in a > > per-chip list thanks to the mv88e6xxx_add/del_xxx_rule() > > helpers. These helpers are then called from various callbacks: > > * mv88e6xxx_port_fdb_add/del() > > * mv88e6xxx_port_mdb_add/del() > > * mv88e6xxx_port_vlan_add/del() > > * mv88e6xxx_port_bridge_join/leave() > > * mv88e6xxx_crosschip_bridge_join/leave() > > > > To avoid recursion problems when replaying the rules, the content of > > the above *_add()/*_join() callbacks has been moved in separate > > helpers with a '_' prefix. Hence, each callback just calls the > > corresponding helper and the corresponding *_add_xxx_rule(). > > None of this should be done in the driver IMHO, because this is > presumably applicable to all switch devices that lose their state during > suspend/resume, so at best, this should be moved to the core DSA layer, > but doing this means that we should also have a well established > contract between the DSA layer and individual switch drivers as far as > quiescing/saving/restoring state goes. > > By moving things to the core we can also more tightly control what data > structures get used to represent e.g.: VLANs, FDBs, MDBs etc and > possibly push/utilize caching into the original subsystem. For instance > VLAN/bridge already do maintain caches of VLANs, so if we could somehow > expose those, we would not bloat the kernel's memory footprint by having > an additional layer to maintain with identical information. So you suggest to move the intelligence of FDBs/MDBs in net/dsa/port.c, is this right? I don't see where VLAN and bridge information are cached, can you point me to the relevant locations? What about cross-chip bridges? There is nothing about them in net/dsa/port.c. The implementation I see in the mv88e6xxx driver only touches the PVT but I don't get whether we should handle this calls like regular bridge-join/leave events or not (maybe they are cached with regular bridge events?). Thanks, Miquèl ^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [PATCH net-next v2 1/2] net: dsa: mv88e6xxx: Save switch rules 2019-01-28 14:24 ` Miquel Raynal @ 2019-01-28 14:44 ` Andrew Lunn 2019-01-28 15:57 ` Miquel Raynal 0 siblings, 1 reply; 20+ messages in thread From: Andrew Lunn @ 2019-01-28 14:44 UTC (permalink / raw) To: Miquel Raynal Cc: Florian Fainelli, Vivien Didelot, David S. Miller, netdev, linux-kernel, Thomas Petazzoni, Gregory Clement, Antoine Tenart, Maxime Chevallier, Nadav Haklai > I don't see where VLAN and bridge information are cached, can you point > me to the relevant locations? Miquèl The bridge should have all that information. You need to ask it to enumerate the current configuration and replay it to the switch. There might be something in the Mellanox driver you can copy? But i've not looked, i'm just guessing. We also need to think about how we are going to test this. There is a lot of state information in a switch. So we are going to need some pretty good tests to show we have recreated all of it. Andrew ^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [PATCH net-next v2 1/2] net: dsa: mv88e6xxx: Save switch rules 2019-01-28 14:44 ` Andrew Lunn @ 2019-01-28 15:57 ` Miquel Raynal 2019-01-28 17:42 ` Andrew Lunn 0 siblings, 1 reply; 20+ messages in thread From: Miquel Raynal @ 2019-01-28 15:57 UTC (permalink / raw) To: Andrew Lunn Cc: Florian Fainelli, Vivien Didelot, David S. Miller, netdev, linux-kernel, Thomas Petazzoni, Gregory Clement, Antoine Tenart, Maxime Chevallier, Nadav Haklai Hi Andrew, Thanks for helping! Andrew Lunn <andrew@lunn.ch> wrote on Mon, 28 Jan 2019 15:44:17 +0100: > > I don't see where VLAN and bridge information are cached, can you point > > me to the relevant locations? > > Miquèl > > The bridge should have all that information. You need to ask it to > enumerate the current configuration and replay it to the switch. > > There might be something in the Mellanox driver you can copy? But i've > not looked, i'm just guessing. I am still searching but so far I did not find a mechanism reading the configuration of the bridge out of a 'net' object. Indeed there are multiple lists with the configuration but they are all 'mellanox' objects, they do not belong to the core. Maybe I don't find this configuration because I don't know what it is. I imagine this configuration being one (or multiple) list(s), stored somewhere in a net_device being a bridge. Am I on the wrong path? Otherwise I might just save my own structures in net/dsa/switch.c like I did for the mv88e6xx driver, and once this works, net-folks might want to optimize the memory consumption and re-use the bridge configuration directly? > We also need to think about how we are going to test this. There is a > lot of state information in a switch. So we are going to need some > pretty good tests to show we have recreated all of it. My understanding of all this is rather short, until know I used what you proposed in the v1 of this series but I am all ears if I need to add anything to my test list. Thanks, Miquèl ^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [PATCH net-next v2 1/2] net: dsa: mv88e6xxx: Save switch rules 2019-01-28 15:57 ` Miquel Raynal @ 2019-01-28 17:42 ` Andrew Lunn 2019-01-29 9:01 ` Miquel Raynal 0 siblings, 1 reply; 20+ messages in thread From: Andrew Lunn @ 2019-01-28 17:42 UTC (permalink / raw) To: Miquel Raynal Cc: Florian Fainelli, Vivien Didelot, David S. Miller, netdev, linux-kernel, Thomas Petazzoni, Gregory Clement, Antoine Tenart, Maxime Chevallier, Nadav Haklai On Mon, Jan 28, 2019 at 04:57:49PM +0100, Miquel Raynal wrote: > Hi Andrew, > > Thanks for helping! > > Andrew Lunn <andrew@lunn.ch> wrote on Mon, 28 Jan 2019 15:44:17 +0100: > > > > I don't see where VLAN and bridge information are cached, can you point > > > me to the relevant locations? > > > > Miquèl > > > > The bridge should have all that information. You need to ask it to > > enumerate the current configuration and replay it to the switch. > > > > There might be something in the Mellanox driver you can copy? But i've > > not looked, i'm just guessing. > > I am still searching but so far I did not find a mechanism reading the > configuration of the bridge out of a 'net' object. Indeed there are > multiple lists with the configuration but they are all 'mellanox' > objects, they do not belong to the core. Hi Miquèl Look at how iproute2 works. How does the bridge command enumerate the fdb and mdb's? How does bridge vlan show work? bridge link show? See if you can use this infrastructure within the kernel. > > We also need to think about how we are going to test this. There is a > > lot of state information in a switch. So we are going to need some > > pretty good tests to show we have recreated all of it. > > My understanding of all this is rather short, until know I used what > you proposed in the v1 of this series but I am all ears if I need to > add anything to my test list. What you probably need is a generic DSA test suite, with a number of hardware devices, with different generations of mv88e6xxx devices, and ideally different sf2, kzs, etc switches. Setup a configuration and test is works correctly. Suspend, resume, and test is still works. And you probably need to go through a number of cycles of suspend/resume. And you are going to need to maintain that for a number of years, testing every release, to see what breaks as we add new features and new devices. There also needs to be some though put into what happens when the network changes while the switch is suspended. A port looses its link, a port comes up, an SFP module is ejected, and SFP module is inserted. The PTP grand master moves, etc. I hope the usual mechanisms just work, but it all needs testing. S2RAM is hard for a device like this. It is not something i personally would want to do :-( Andrew ^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [PATCH net-next v2 1/2] net: dsa: mv88e6xxx: Save switch rules 2019-01-28 17:42 ` Andrew Lunn @ 2019-01-29 9:01 ` Miquel Raynal 2019-01-29 14:51 ` Andrew Lunn 0 siblings, 1 reply; 20+ messages in thread From: Miquel Raynal @ 2019-01-29 9:01 UTC (permalink / raw) To: Andrew Lunn Cc: Florian Fainelli, Vivien Didelot, David S. Miller, netdev, linux-kernel, Thomas Petazzoni, Gregory Clement, Antoine Tenart, Maxime Chevallier, Nadav Haklai Hi Andrew, Andrew Lunn <andrew@lunn.ch> wrote on Mon, 28 Jan 2019 18:42:46 +0100: > On Mon, Jan 28, 2019 at 04:57:49PM +0100, Miquel Raynal wrote: > > Hi Andrew, > > > > Thanks for helping! > > > > Andrew Lunn <andrew@lunn.ch> wrote on Mon, 28 Jan 2019 15:44:17 +0100: > > > > > > I don't see where VLAN and bridge information are cached, can you point > > > > me to the relevant locations? > > > > > > Miquèl > > > > > > The bridge should have all that information. You need to ask it to > > > enumerate the current configuration and replay it to the switch. > > > > > > There might be something in the Mellanox driver you can copy? But i've > > > not looked, i'm just guessing. > > > > I am still searching but so far I did not find a mechanism reading the > > configuration of the bridge out of a 'net' object. Indeed there are > > multiple lists with the configuration but they are all 'mellanox' > > objects, they do not belong to the core. > > Hi Miquèl > > Look at how iproute2 works. How does the bridge command enumerate the > fdb and mdb's? How does bridge vlan show work? bridge link show? See > if you can use this infrastructure within the kernel. Thanks! > > > > We also need to think about how we are going to test this. There is a > > > lot of state information in a switch. So we are going to need some > > > pretty good tests to show we have recreated all of it. > > > > My understanding of all this is rather short, until know I used what > > you proposed in the v1 of this series but I am all ears if I need to > > add anything to my test list. > > What you probably need is a generic DSA test suite, with a number of > hardware devices, with different generations of mv88e6xxx devices, and > ideally different sf2, kzs, etc switches. Setup a configuration and > test is works correctly. Suspend, resume, and test is still works. And > you probably need to go through a number of cycles of suspend/resume. > And you are going to need to maintain that for a number of years, > testing every release, to see what breaks as we add new features and > new devices. I am very sorry but I kind of disagree with the above proposal. Usually contributors try to write the best solution with the help of the community, test on the hardware they have in hand and propose the changes. I cannot bond on a 10-years involvement in testing several switches over the releases. Today, there is no S2RAM support for switches. First, I proposed to add suspend/resume callbacks to the mv88e6xxx driver - just enough to avoid crashing the kernel. It was reported that the configuration was lost so I wrote a rule-saving mechanism to replay the rules at resume. I was told that this mechanism would best fit in the DSA core directly. I am open to do that, I don't think it is that much work. But it is also required that I use as less memory as possible. This is going to take more time but I think I can do it as well. At least for a minimal set of configuration. Then, why not let other people improve things as they need? IIUC Switch S2RAM does not work at all, I may try to improve the situation but I do not have the abilities nor the time to do it exhaustively for every piece of hardware and every situation. > > There also needs to be some though put into what happens when the > network changes while the switch is suspended. A port looses its link, > a port comes up, an SFP module is ejected, and SFP module is > inserted. The PTP grand master moves, etc. I hope the usual mechanisms > just work, but it all needs testing. Is this really specific to switches? I know it is an issue and I understand you would prefer not to support S2RAM at all rather than addressing part of it, but isn't it better to support the simplest situation first, than supporting nothing at all? Thanks Andrew for your guidance and help anyway, Miquèl ^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [PATCH net-next v2 1/2] net: dsa: mv88e6xxx: Save switch rules 2019-01-29 9:01 ` Miquel Raynal @ 2019-01-29 14:51 ` Andrew Lunn 2019-01-29 15:46 ` Vivien Didelot 0 siblings, 1 reply; 20+ messages in thread From: Andrew Lunn @ 2019-01-29 14:51 UTC (permalink / raw) To: Miquel Raynal Cc: Florian Fainelli, Vivien Didelot, David S. Miller, netdev, linux-kernel, Thomas Petazzoni, Gregory Clement, Antoine Tenart, Maxime Chevallier, Nadav Haklai On Tue, Jan 29, 2019 at 10:01:17AM +0100, Miquel Raynal wrote: > Hi Andrew, > > Andrew Lunn <andrew@lunn.ch> wrote on Mon, 28 Jan 2019 18:42:46 +0100: > > > On Mon, Jan 28, 2019 at 04:57:49PM +0100, Miquel Raynal wrote: > > > Hi Andrew, > > > > > > Thanks for helping! > > > > > > Andrew Lunn <andrew@lunn.ch> wrote on Mon, 28 Jan 2019 15:44:17 +0100: > > > > > > > > I don't see where VLAN and bridge information are cached, can you point > > > > > me to the relevant locations? > > > > > > > > Miquèl > > > > > > > > The bridge should have all that information. You need to ask it to > > > > enumerate the current configuration and replay it to the switch. > > > > > > > > There might be something in the Mellanox driver you can copy? But i've > > > > not looked, i'm just guessing. > > > > > > I am still searching but so far I did not find a mechanism reading the > > > configuration of the bridge out of a 'net' object. Indeed there are > > > multiple lists with the configuration but they are all 'mellanox' > > > objects, they do not belong to the core. > > > > Hi Miquèl > > > > Look at how iproute2 works. How does the bridge command enumerate the > > fdb and mdb's? How does bridge vlan show work? bridge link show? See > > if you can use this infrastructure within the kernel. > > Thanks! > > > > > > > We also need to think about how we are going to test this. There is a > > > > lot of state information in a switch. So we are going to need some > > > > pretty good tests to show we have recreated all of it. > > > > > > My understanding of all this is rather short, until know I used what > > > you proposed in the v1 of this series but I am all ears if I need to > > > add anything to my test list. > > > > What you probably need is a generic DSA test suite, with a number of > > hardware devices, with different generations of mv88e6xxx devices, and > > ideally different sf2, kzs, etc switches. Setup a configuration and > > test is works correctly. Suspend, resume, and test is still works. And > > you probably need to go through a number of cycles of suspend/resume. > > And you are going to need to maintain that for a number of years, > > testing every release, to see what breaks as we add new features and > > new devices. > > I am very sorry but I kind of disagree with the above proposal. Usually > contributors try to write the best solution with the help of the > community, test on the hardware they have in hand and propose the > changes. I cannot bond on a 10-years involvement in testing several > switches over the releases. Hi Miquèl I was trying to point out this is a very hard subject to tackle. And to do it right is not going to be a few patches. It needs a lot of work, and a lot of testing, and it needs ongoing work because the mv88e6xxx driver is not complete, there are more features to add, which are going to need suspend/resume support adding. > Today, there is no S2RAM support for switches. First, I proposed to add > suspend/resume callbacks to the mv88e6xxx driver - just enough to avoid > crashing the kernel. Then i would suggest the mv88e6xxx refuses the suspend. Actually that probably is the first correct step. We don't have suspend support, so stop the suspend happening, so preventing the kernel crash. Having to maintain the mv88e6xxx, i don't want a suspend which might work in the simplest configuration, but fails badly for more complex configurations. Before accepting any patches, i want a good feeling it works correctly. I would be willing to accept support and testing on one Marvell family of switches, but again, i want to know it is well tested. And i want to know somebody is going to stay around and look after the support as the switch driver develops new features, which are going to need suspend/resume support. If you are only willing to consider a limited number of features, you need to track if the switch is still within those limited set of features, and refuse the suspend if not. > > There also needs to be some though put into what happens when the > > network changes while the switch is suspended. A port looses its link, > > a port comes up, an SFP module is ejected, and SFP module is > > inserted. The PTP grand master moves, etc. I hope the usual mechanisms > > just work, but it all needs testing. > > Is this really specific to switches? I know it is an issue and I > understand you would prefer not to support S2RAM at all rather than > addressing part of it, but isn't it better to support the simplest > situation first, than supporting nothing at all? Worst case scenario, you induce a loop in your network, and a broadcast storm takes down the whole network. It is unlikely, but it is very disruptive if it does happen. It is also the sort of situation which is probably not going to get tested, making it more likely to actually happen. And this is specific to switches. A single network card cannot do this, you need two ports to form a loop. Andrew ^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [PATCH net-next v2 1/2] net: dsa: mv88e6xxx: Save switch rules 2019-01-29 14:51 ` Andrew Lunn @ 2019-01-29 15:46 ` Vivien Didelot 2019-01-30 9:46 ` Miquel Raynal 0 siblings, 1 reply; 20+ messages in thread From: Vivien Didelot @ 2019-01-29 15:46 UTC (permalink / raw) To: Andrew Lunn Cc: Miquel Raynal, Florian Fainelli, David S. Miller, netdev, linux-kernel, Thomas Petazzoni, Gregory Clement, Antoine Tenart, Maxime Chevallier, Nadav Haklai Hi Miquèl, On Tue, 29 Jan 2019 15:51:57 +0100, Andrew Lunn <andrew@lunn.ch> wrote: > > Today, there is no S2RAM support for switches. First, I proposed to add > > suspend/resume callbacks to the mv88e6xxx driver - just enough to avoid > > crashing the kernel. > > Then i would suggest the mv88e6xxx refuses the suspend. Actually that > probably is the first correct step. We don't have suspend support, so > stop the suspend happening, so preventing the kernel crash. I am not confortable with adding support for S2RAM in mv88e6xxx yet because as it was explained, we are aware of much complicated scenarios out there to pretend that DSA /partly/ supports suspend-resume. The prefered approach for the moment is to keep things simple and not supporting this feature yet, especially at the mv88e6xxx driver level. However crashing is unacceptable so I'm backing Andrew's point here, please submit a fix to prevent the suspend (and crash) for the moment. Sorry if you felt that your work is being delayed, it is much appreciated! Thanks, Vivien ^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [PATCH net-next v2 1/2] net: dsa: mv88e6xxx: Save switch rules 2019-01-29 15:46 ` Vivien Didelot @ 2019-01-30 9:46 ` Miquel Raynal 2019-01-30 14:54 ` Andrew Lunn 2019-01-31 0:46 ` Vivien Didelot 0 siblings, 2 replies; 20+ messages in thread From: Miquel Raynal @ 2019-01-30 9:46 UTC (permalink / raw) To: Vivien Didelot Cc: Andrew Lunn, Florian Fainelli, David S. Miller, netdev, linux-kernel, Thomas Petazzoni, Gregory Clement, Antoine Tenart, Maxime Chevallier, Nadav Haklai Hi Vivien & Andrew, Vivien Didelot <vivien.didelot@gmail.com> wrote on Tue, 29 Jan 2019 10:46:13 -0500: > Hi Miquèl, > > On Tue, 29 Jan 2019 15:51:57 +0100, Andrew Lunn <andrew@lunn.ch> wrote: > > > > Today, there is no S2RAM support for switches. First, I proposed to add > > > suspend/resume callbacks to the mv88e6xxx driver - just enough to avoid > > > crashing the kernel. > > > > Then i would suggest the mv88e6xxx refuses the suspend. Actually that > > probably is the first correct step. We don't have suspend support, so > > stop the suspend happening, so preventing the kernel crash. > > I am not confortable with adding support for S2RAM in mv88e6xxx yet because > as it was explained, we are aware of much complicated scenarios out there > to pretend that DSA /partly/ supports suspend-resume. The prefered approach > for the moment is to keep things simple and not supporting this feature yet, > especially at the mv88e6xxx driver level. > > However crashing is unacceptable so I'm backing Andrew's point here, please > submit a fix to prevent the suspend (and crash) for the moment. > > Sorry if you felt that your work is being delayed, it is much appreciated! Thanks for the more detailed explanation, I got your point and I better understand your reluctance. So your proposal is to refuse suspending when using a mv88e6xxx switch. What about the current situation where suspending is allowed, but all the configuration gone? As long as all the ports are disabled during suspend, it should not hurt anything, right? Plus, this is what the bcm_sf2 and qca8k drivers are doing. I can even add an error message in the resume path to warn about this drawback. Thanks, Miquèl ^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [PATCH net-next v2 1/2] net: dsa: mv88e6xxx: Save switch rules 2019-01-30 9:46 ` Miquel Raynal @ 2019-01-30 14:54 ` Andrew Lunn 2019-01-31 0:46 ` Vivien Didelot 1 sibling, 0 replies; 20+ messages in thread From: Andrew Lunn @ 2019-01-30 14:54 UTC (permalink / raw) To: Miquel Raynal Cc: Vivien Didelot, Florian Fainelli, David S. Miller, netdev, linux-kernel, Thomas Petazzoni, Gregory Clement, Antoine Tenart, Maxime Chevallier, Nadav Haklai > So your proposal is to refuse suspending when using a mv88e6xxx switch. Hi Miquèl That is the first step. It makes the mv88e6xxx suspend compliant, in that it currently does not support suspend. > What about the current situation where suspending is allowed, but all > the configuration gone? That is broken. The whole point of suspending is that you resume back to the original state. Andrew ^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [PATCH net-next v2 1/2] net: dsa: mv88e6xxx: Save switch rules 2019-01-30 9:46 ` Miquel Raynal 2019-01-30 14:54 ` Andrew Lunn @ 2019-01-31 0:46 ` Vivien Didelot 2019-02-01 11:01 ` Miquel Raynal 1 sibling, 1 reply; 20+ messages in thread From: Vivien Didelot @ 2019-01-31 0:46 UTC (permalink / raw) To: Miquel Raynal Cc: Andrew Lunn, Florian Fainelli, David S. Miller, netdev, linux-kernel, Thomas Petazzoni, Gregory Clement, Antoine Tenart, Maxime Chevallier, Nadav Haklai Hi Miquèl, On Wed, 30 Jan 2019 10:46:06 +0100, Miquel Raynal <miquel.raynal@bootlin.com> wrote: > > > > Today, there is no S2RAM support for switches. First, I proposed to add > > > > suspend/resume callbacks to the mv88e6xxx driver - just enough to avoid > > > > crashing the kernel. > > > > > > Then i would suggest the mv88e6xxx refuses the suspend. Actually that > > > probably is the first correct step. We don't have suspend support, so > > > stop the suspend happening, so preventing the kernel crash. Actually can you show me the crash that is happening? ^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [PATCH net-next v2 1/2] net: dsa: mv88e6xxx: Save switch rules 2019-01-31 0:46 ` Vivien Didelot @ 2019-02-01 11:01 ` Miquel Raynal 2019-02-01 14:08 ` Andrew Lunn 0 siblings, 1 reply; 20+ messages in thread From: Miquel Raynal @ 2019-02-01 11:01 UTC (permalink / raw) To: Vivien Didelot Cc: Andrew Lunn, Florian Fainelli, David S. Miller, netdev, linux-kernel, Thomas Petazzoni, Gregory Clement, Antoine Tenart, Maxime Chevallier, Nadav Haklai Hi Vivien, Vivien Didelot <vivien.didelot@gmail.com> wrote on Wed, 30 Jan 2019 19:46:08 -0500: > Hi Miquèl, > > On Wed, 30 Jan 2019 10:46:06 +0100, Miquel Raynal <miquel.raynal@bootlin.com> wrote: > > > > > > Today, there is no S2RAM support for switches. First, I proposed to add > > > > > suspend/resume callbacks to the mv88e6xxx driver - just enough to avoid > > > > > crashing the kernel. > > > > > > > > Then i would suggest the mv88e6xxx refuses the suspend. Actually that > > > > probably is the first correct step. We don't have suspend support, so > > > > stop the suspend happening, so preventing the kernel crash. > > Actually can you show me the crash that is happening? Sure, here it is: http://code.bulix.org/swwb11-569137 Actually it is a silent crash but the platform never resumes. I am pretty sure this is due to the kthread_queue_delayed_work() loop which might access registers before it is allowed to do so. In my proposal I just canceled it at suspend and restarted it at resume. Next week I will send a patch to refuse the suspend as you both suggested and if people want to suspend, they will have to remove the switch support. Thanks, Miquèl ^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [PATCH net-next v2 1/2] net: dsa: mv88e6xxx: Save switch rules 2019-02-01 11:01 ` Miquel Raynal @ 2019-02-01 14:08 ` Andrew Lunn 2019-02-01 14:43 ` Miquel Raynal 0 siblings, 1 reply; 20+ messages in thread From: Andrew Lunn @ 2019-02-01 14:08 UTC (permalink / raw) To: Miquel Raynal Cc: Vivien Didelot, Florian Fainelli, David S. Miller, netdev, linux-kernel, Thomas Petazzoni, Gregory Clement, Antoine Tenart, Maxime Chevallier, Nadav Haklai On Fri, Feb 01, 2019 at 12:01:19PM +0100, Miquel Raynal wrote: > Hi Vivien, > > Vivien Didelot <vivien.didelot@gmail.com> wrote on Wed, 30 Jan 2019 > 19:46:08 -0500: > > > Hi Miquèl, > > > > On Wed, 30 Jan 2019 10:46:06 +0100, Miquel Raynal <miquel.raynal@bootlin.com> wrote: > > > > > > > > Today, there is no S2RAM support for switches. First, I proposed to add > > > > > > suspend/resume callbacks to the mv88e6xxx driver - just enough to avoid > > > > > > crashing the kernel. > > > > > > > > > > Then i would suggest the mv88e6xxx refuses the suspend. Actually that > > > > > probably is the first correct step. We don't have suspend support, so > > > > > stop the suspend happening, so preventing the kernel crash. > > > > Actually can you show me the crash that is happening? > > Sure, here it is: http://code.bulix.org/swwb11-569137 > > Actually it is a silent crash but the platform never resumes. I am > pretty sure this is due to the kthread_queue_delayed_work() loop which > might access registers before it is allowed to do so. Hi Miquel That sounds like it is an MDIO driver problem, or at least, a resume ordering problem. You need to ensure that the MDIO bus driver is resumed before the switch driver. Also, that the switch is suspended before the MDIO bus driver is suspended. Andrew ^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [PATCH net-next v2 1/2] net: dsa: mv88e6xxx: Save switch rules 2019-02-01 14:08 ` Andrew Lunn @ 2019-02-01 14:43 ` Miquel Raynal 0 siblings, 0 replies; 20+ messages in thread From: Miquel Raynal @ 2019-02-01 14:43 UTC (permalink / raw) To: Andrew Lunn Cc: Vivien Didelot, Florian Fainelli, David S. Miller, netdev, linux-kernel, Thomas Petazzoni, Gregory Clement, Antoine Tenart, Maxime Chevallier, Nadav Haklai Hi Andrew, Andrew Lunn <andrew@lunn.ch> wrote on Fri, 1 Feb 2019 15:08:31 +0100: > On Fri, Feb 01, 2019 at 12:01:19PM +0100, Miquel Raynal wrote: > > Hi Vivien, > > > > Vivien Didelot <vivien.didelot@gmail.com> wrote on Wed, 30 Jan 2019 > > 19:46:08 -0500: > > > > > Hi Miquèl, > > > > > > On Wed, 30 Jan 2019 10:46:06 +0100, Miquel Raynal <miquel.raynal@bootlin.com> wrote: > > > > > > > > > > Today, there is no S2RAM support for switches. First, I proposed to add > > > > > > > suspend/resume callbacks to the mv88e6xxx driver - just enough to avoid > > > > > > > crashing the kernel. > > > > > > > > > > > > Then i would suggest the mv88e6xxx refuses the suspend. Actually that > > > > > > probably is the first correct step. We don't have suspend support, so > > > > > > stop the suspend happening, so preventing the kernel crash. > > > > > > Actually can you show me the crash that is happening? > > > > Sure, here it is: http://code.bulix.org/swwb11-569137 > > > > Actually it is a silent crash but the platform never resumes. I am > > pretty sure this is due to the kthread_queue_delayed_work() loop which > > might access registers before it is allowed to do so. > > Hi Miquel > > That sounds like it is an MDIO driver problem, or at least, a resume > ordering problem. You need to ensure that the MDIO bus driver is > resumed before the switch driver. Also, that the switch is suspended > before the MDIO bus driver is suspended. I don't think there is an ordering problem. The MDIO bus is suspended after the switch and resumed before. But if there is no cancellation of the work thread (which is always automatically restarted) in the suspend path, soon or later this work will run at a time when the MDIO bus is still not accessible and will freeze the platform entirely. Thanks, Miquèl ^ permalink raw reply [flat|nested] 20+ messages in thread
* [PATCH net-next v2 2/2] net: dsa: mv88e6xxx: Add suspend to RAM support 2019-01-25 9:55 [PATCH net-next v2 0/2] mv88e6xxx DSA suspend to RAM support Miquel Raynal 2019-01-25 9:55 ` [PATCH net-next v2 1/2] net: dsa: mv88e6xxx: Save switch rules Miquel Raynal @ 2019-01-25 9:55 ` Miquel Raynal 2019-01-27 21:22 ` [PATCH net-next v2 0/2] mv88e6xxx DSA " David Miller 2 siblings, 0 replies; 20+ messages in thread From: Miquel Raynal @ 2019-01-25 9:55 UTC (permalink / raw) To: Andrew Lunn, Vivien Didelot, Florian Fainelli, David S. Miller Cc: netdev, linux-kernel, Thomas Petazzoni, Gregory Clement, Antoine Tenart, Maxime Chevallier, Nadav Haklai, Miquel Raynal Bring S2RAM support to the mv88e6xxx DSA driver. The content of the *_irq_poll() helper is moved in *_do_irq_poll() so that that the function can be called from the ->resume() callback without using the *work pointer. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> --- Changes since v1: ================= * Added the logic to replay rules. * Did not add any port_disable/enable() calls as this will be taken care of by Vivien's patches. drivers/net/dsa/mv88e6xxx/chip.c | 89 ++++++++++++++++++++++++++++++-- 1 file changed, 86 insertions(+), 3 deletions(-) diff --git a/drivers/net/dsa/mv88e6xxx/chip.c b/drivers/net/dsa/mv88e6xxx/chip.c index 428177f80abd..e83c02aaca49 100644 --- a/drivers/net/dsa/mv88e6xxx/chip.c +++ b/drivers/net/dsa/mv88e6xxx/chip.c @@ -547,15 +547,21 @@ static int mv88e6xxx_g1_irq_setup(struct mv88e6xxx_chip *chip) return err; } +static void mv88e6xxx_do_irq_poll(struct mv88e6xxx_chip *chip) +{ + mv88e6xxx_g1_irq_thread_work(chip); + + kthread_queue_delayed_work(chip->kworker, &chip->irq_poll_work, + msecs_to_jiffies(100)); +} + static void mv88e6xxx_irq_poll(struct kthread_work *work) { struct mv88e6xxx_chip *chip = container_of(work, struct mv88e6xxx_chip, irq_poll_work.work); - mv88e6xxx_g1_irq_thread_work(chip); - kthread_queue_delayed_work(chip->kworker, &chip->irq_poll_work, - msecs_to_jiffies(100)); + mv88e6xxx_do_irq_poll(chip); } static int mv88e6xxx_irq_poll_setup(struct mv88e6xxx_chip *chip) @@ -4855,6 +4861,82 @@ static const void *pdata_device_get_match_data(struct device *dev) return NULL; } +static int __maybe_unused mv88e6xxx_suspend(struct device *dev) +{ + struct dsa_switch *ds = dev_get_drvdata(dev); + struct mv88e6xxx_chip *chip = ds->priv; + + kthread_cancel_delayed_work_sync(&chip->irq_poll_work); + + return dsa_switch_suspend(ds); +} + +static int __maybe_unused mv88e6xxx_resume(struct device *dev) +{ + struct dsa_switch *ds = dev_get_drvdata(dev); + struct mv88e6xxx_chip *chip = ds->priv; + struct mv88e6xxx_rule *rule; + int ret; + + mv88e6xxx_phy_init(chip); + + mutex_lock(&chip->reg_lock); + ret = mv88e6xxx_switch_reset(chip); + mutex_unlock(&chip->reg_lock); + if (ret) { + dev_err(dev, "Failed to reset the switch\n"); + return ret; + } + + ret = mv88e6xxx_setup(ds); + if (ret) { + dev_err(dev, "Failed to setup the switch\n"); + return ret; + } + + mv88e6xxx_do_irq_poll(chip); + + list_for_each_entry(rule, &chip->rules, node) { + switch (rule->type) { + case FDB_RULE: + ret = _mv88e6xxx_port_fdb_add(chip, rule->port, + rule->params.db.addr, + rule->params.db.vid); + break; + case MDB_RULE: + ret = _mv88e6xxx_port_mdb_add(chip, rule->port, + rule->params.db.addr, + rule->params.db.vid); + break; + case VLAN_RULE: + ret = _mv88e6xxx_port_vlan_add(chip, rule->port, + &rule->params.vlan); + break; + case BRIDGE_RULE: + ret = _mv88e6xxx_port_bridge_join(chip, rule->port, + rule->params.br); + break; + case CC_BRIDGE_RULE: + ret = _mv88e6xxx_crosschip_bridge_join(chip, + rule->params.crosschip.dev, + rule->port, + rule->params.crosschip.br); + break; + default: + dev_warn(chip->dev, "Unknown rule type (%d)\n", + rule->type); + continue; + } + + if (ret) + dev_warn(chip->dev, "Cannot re-apply rule\n"); + } + + return dsa_switch_resume(ds); +} + +static SIMPLE_DEV_PM_OPS(mv88e6xxx_pm_ops, mv88e6xxx_suspend, mv88e6xxx_resume); + static int mv88e6xxx_probe(struct mdio_device *mdiodev) { struct dsa_mv88e6xxx_pdata *pdata = mdiodev->dev.platform_data; @@ -5041,6 +5123,7 @@ static struct mdio_driver mv88e6xxx_driver = { .mdiodrv.driver = { .name = "mv88e6085", .of_match_table = mv88e6xxx_of_match, + .pm = &mv88e6xxx_pm_ops, }, }; -- 2.19.1 ^ permalink raw reply related [flat|nested] 20+ messages in thread
* Re: [PATCH net-next v2 0/2] mv88e6xxx DSA suspend to RAM support 2019-01-25 9:55 [PATCH net-next v2 0/2] mv88e6xxx DSA suspend to RAM support Miquel Raynal 2019-01-25 9:55 ` [PATCH net-next v2 1/2] net: dsa: mv88e6xxx: Save switch rules Miquel Raynal 2019-01-25 9:55 ` [PATCH net-next v2 2/2] net: dsa: mv88e6xxx: Add suspend to RAM support Miquel Raynal @ 2019-01-27 21:22 ` David Miller 2019-01-27 21:46 ` Andrew Lunn 2 siblings, 1 reply; 20+ messages in thread From: David Miller @ 2019-01-27 21:22 UTC (permalink / raw) To: miquel.raynal Cc: andrew, vivien.didelot, f.fainelli, netdev, linux-kernel, thomas.petazzoni, gregory.clement, antoine.tenart, maxime.chevallier, nadavh From: Miquel Raynal <miquel.raynal@bootlin.com> Date: Fri, 25 Jan 2019 10:55:05 +0100 > After a first attempt of bringing S2RAM support to the DSA switch, it > has been reported that a part of the configuration was lost during the > cycle. This second version adds a first patch that saves the rules in > a per-chip list when they are applied, so that in the second patch we > bring S2RAM support by also re-applying these rules. ... It seems like the discussion on patch #1 has hit a brick wall. The last suggestion was to use: + switch (mode) { + case PHY_INTERFACE_MODE_2500BASEX: + phydev->speed = SPEED_2500; + break; + case PHY_INTERFACE_MODE_10GKR: + phydev->speed = SPEED_10000; + break; + in dsa_port_fixed_link_register_of(), but that doesn't work because swphy will fail without speed=1000 in the dts. Well, whatever is decided, the commit message need to be updated to explain why this course of action for the most immediate fix was ultimately taken. Thanks. ^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [PATCH net-next v2 0/2] mv88e6xxx DSA suspend to RAM support 2019-01-27 21:22 ` [PATCH net-next v2 0/2] mv88e6xxx DSA " David Miller @ 2019-01-27 21:46 ` Andrew Lunn 2019-01-28 3:44 ` David Miller 0 siblings, 1 reply; 20+ messages in thread From: Andrew Lunn @ 2019-01-27 21:46 UTC (permalink / raw) To: David Miller Cc: miquel.raynal, vivien.didelot, f.fainelli, netdev, linux-kernel, thomas.petazzoni, gregory.clement, antoine.tenart, maxime.chevallier, nadavh On Sun, Jan 27, 2019 at 01:22:50PM -0800, David Miller wrote: > From: Miquel Raynal <miquel.raynal@bootlin.com> > Date: Fri, 25 Jan 2019 10:55:05 +0100 > > > After a first attempt of bringing S2RAM support to the DSA switch, it > > has been reported that a part of the configuration was lost during the > > cycle. This second version adds a first patch that saves the rules in > > a per-chip list when they are applied, so that in the second patch we > > bring S2RAM support by also re-applying these rules. > ... > > It seems like the discussion on patch #1 has hit a brick wall. > > The last suggestion was to use: > > + switch (mode) { > + case PHY_INTERFACE_MODE_2500BASEX: > + phydev->speed = SPEED_2500; > + break; > + case PHY_INTERFACE_MODE_10GKR: > + phydev->speed = SPEED_10000; > + break; > + > > in dsa_port_fixed_link_register_of(), but that doesn't work > because swphy will fail without speed=1000 in the dts. > > Well, whatever is decided, the commit message need to be updated > to explain why this course of action for the most immediate fix > was ultimately taken. Hi David Err. I think you are replying to the wrong patch? This comment fits to https://www.spinics.net/lists/netdev/msg546662.html Although i don't like it, i think for the moment we are going to have to accept the proposed fix. Andrew ^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [PATCH net-next v2 0/2] mv88e6xxx DSA suspend to RAM support 2019-01-27 21:46 ` Andrew Lunn @ 2019-01-28 3:44 ` David Miller 0 siblings, 0 replies; 20+ messages in thread From: David Miller @ 2019-01-28 3:44 UTC (permalink / raw) To: andrew Cc: miquel.raynal, vivien.didelot, f.fainelli, netdev, linux-kernel, thomas.petazzoni, gregory.clement, antoine.tenart, maxime.chevallier, nadavh From: Andrew Lunn <andrew@lunn.ch> Date: Sun, 27 Jan 2019 22:46:52 +0100 > I think you are replying to the wrong patch? This comment fits to > > https://www.spinics.net/lists/netdev/msg546662.html I noticed that right after I hit send, you are right. Sorry for the confusion. > Although i don't like it, i think for the moment we are going to have > to accept the proposed fix. Indeed. ^ permalink raw reply [flat|nested] 20+ messages in thread
end of thread, other threads:[~2019-02-01 14:43 UTC | newest] Thread overview: 20+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2019-01-25 9:55 [PATCH net-next v2 0/2] mv88e6xxx DSA suspend to RAM support Miquel Raynal 2019-01-25 9:55 ` [PATCH net-next v2 1/2] net: dsa: mv88e6xxx: Save switch rules Miquel Raynal 2019-01-25 18:37 ` Florian Fainelli 2019-01-28 14:24 ` Miquel Raynal 2019-01-28 14:44 ` Andrew Lunn 2019-01-28 15:57 ` Miquel Raynal 2019-01-28 17:42 ` Andrew Lunn 2019-01-29 9:01 ` Miquel Raynal 2019-01-29 14:51 ` Andrew Lunn 2019-01-29 15:46 ` Vivien Didelot 2019-01-30 9:46 ` Miquel Raynal 2019-01-30 14:54 ` Andrew Lunn 2019-01-31 0:46 ` Vivien Didelot 2019-02-01 11:01 ` Miquel Raynal 2019-02-01 14:08 ` Andrew Lunn 2019-02-01 14:43 ` Miquel Raynal 2019-01-25 9:55 ` [PATCH net-next v2 2/2] net: dsa: mv88e6xxx: Add suspend to RAM support Miquel Raynal 2019-01-27 21:22 ` [PATCH net-next v2 0/2] mv88e6xxx DSA " David Miller 2019-01-27 21:46 ` Andrew Lunn 2019-01-28 3:44 ` David Miller
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).