From: Maxime Chevallier <maxime.chevallier@bootlin.com>
To: davem@davemloft.net
Cc: Maxime Chevallier <maxime.chevallier@bootlin.com>,
netdev@vger.kernel.org, linux-kernel@vger.kernel.org,
Andrew Lunn <andrew@lunn.ch>,
Florian Fainelli <f.fainelli@gmail.com>,
Heiner Kallweit <hkallweit1@gmail.com>,
Russell King <linux@armlinux.org.uk>,
linux-arm-kernel@lists.infradead.org,
Antoine Tenart <antoine.tenart@bootlin.com>,
thomas.petazzoni@bootlin.com, gregory.clement@bootlin.com,
miquel.raynal@bootlin.com, nadavh@marvell.com,
stefanc@marvell.com, mw@semihalf.com
Subject: [PATCH net-next v2 00/10] net: phy: Add support for 2.5GBASET PHYs
Date: Thu, 7 Feb 2019 10:49:29 +0100 [thread overview]
Message-ID: <20190207094939.27369-1-maxime.chevallier@bootlin.com> (raw)
Hello everyone,
This is the second iteration of the series introducing support for
2.5GBASET and 5GBASET to the network PHY infrastructure.
These 2 modes are described in the 802.3bz specifications, and allow to
use 2.5G and 5G speeds on cat5e/cat6 cables.
The required infrastructure code is added for 2.5GBASET and 5GBASET, but
only 2.5GBASET support is added to the Marvell10G driver. The reason is
because the 5GBASER interface mode used to communicate with the MAC
isn't implemented yet, and therefore this can't be tested.
This series has seen some rework since last time, see the full details
in the patches changelog. The main highlights are :
- Patch 1 moves the Pause ans Asym_Pause parameters update after
calling config_init. This allows us to change the phydev->supported
modes in config_init, while still forcing some quirks taken from
phydrv->features, to disable unsupported Pause modes. This was
proposed by Andrew.
- Patch 2 generalizes the way we mask-out modes we don't want to use
when forcing the link speed through DT or ethtool, by walking through
the PHY settings table, as proposed by Russell.
- Patch 4 implements automatic setting of TM, FIBRE and Backplane bits
from the list of supported linkmodes.
- In Patch 5, we only read abilities from the PMA. Pause parameters
aren't built from the genphy_c45_pma_read_abilities, as it was done
in the previous iteration of the patch. We also amke use of
linkmode_mod_bit to make sure we mask-out unsupported modes.
- In Patch 8, we manually check for the PMA device id to see if we have
to use a quirk when reading the 2.5G/5G Extended Abilities
Maxime Chevallier (10):
net: phy: Update PHY linkmodes after config_init
net: phy: Mask-out non-compatible modes when setting the max-speed
net: phy: Move of_set_phy_eee_broken to phy-core.c
net: phy: Automatically fill the generic TP, FIBRE and Backplane modes
net: phy: Extract genphy_c45_pma_read_abilities from marvell10g
net: phy: Add generic support for 2.5GBaseT and 5GBaseT
net: phy: marvell10g: Add support for 2.5GBASET
net: phy: marvell10g: Force reading of 2.5/5G
net: mvpp2: Add 2.5GBaseT support
net: phy: marvell10g: add support for the 88x2110 PHY
.../net/ethernet/marvell/mvpp2/mvpp2_main.c | 1 +
drivers/net/phy/marvell10g.c | 142 +++++------
drivers/net/phy/phy-c45.c | 111 ++++++++
drivers/net/phy/phy-core.c | 72 ++++++
drivers/net/phy/phy_device.c | 237 +++++++++---------
include/linux/linkmode.h | 6 +
include/linux/marvell_phy.h | 2 +
include/linux/phy.h | 3 +
include/uapi/linux/mdio.h | 16 ++
9 files changed, 405 insertions(+), 185 deletions(-)
--
2.19.2
next reply other threads:[~2019-02-07 9:51 UTC|newest]
Thread overview: 27+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-02-07 9:49 Maxime Chevallier [this message]
2019-02-07 9:49 ` [PATCH net-next v2 01/10] net: phy: Update PHY linkmodes after config_init Maxime Chevallier
2019-02-07 10:31 ` Maxime Chevallier
2019-02-07 13:48 ` Andrew Lunn
2019-02-07 13:55 ` Maxime Chevallier
2019-02-07 18:21 ` Heiner Kallweit
2019-02-07 9:49 ` [PATCH net-next v2 02/10] net: phy: Mask-out non-compatible modes when setting the max-speed Maxime Chevallier
2019-02-07 13:59 ` Andrew Lunn
2019-02-07 9:49 ` [PATCH net-next v2 03/10] net: phy: Move of_set_phy_eee_broken to phy-core.c Maxime Chevallier
2019-02-07 14:01 ` Andrew Lunn
2019-02-07 9:49 ` [PATCH net-next v2 04/10] net: phy: Automatically fill the generic TP, FIBRE and Backplane modes Maxime Chevallier
2019-02-07 14:09 ` Andrew Lunn
2019-02-07 14:49 ` Maxime Chevallier
2019-02-07 9:49 ` [PATCH net-next v2 05/10] net: phy: Extract genphy_c45_pma_read_abilities from marvell10g Maxime Chevallier
2019-02-07 9:49 ` [PATCH net-next v2 06/10] net: phy: Add generic support for 2.5GBaseT and 5GBaseT Maxime Chevallier
2019-02-07 9:49 ` [PATCH net-next v2 07/10] net: phy: marvell10g: Add support for 2.5GBASET Maxime Chevallier
2019-02-07 14:15 ` Andrew Lunn
2019-02-07 23:48 ` Russell King - ARM Linux admin
2019-02-20 10:54 ` Maxime Chevallier
2019-02-07 9:49 ` [PATCH net-next v2 08/10] net: phy: marvell10g: Force reading of 2.5/5G Maxime Chevallier
2019-02-07 9:49 ` [PATCH net-next v2 09/10] net: mvpp2: Add 2.5GBaseT support Maxime Chevallier
2019-02-07 14:17 ` Andrew Lunn
2019-02-07 9:49 ` [PATCH net-next v2 10/10] net: phy: marvell10g: add support for the 88x2110 PHY Maxime Chevallier
2019-02-09 13:22 ` [PATCH net-next v2 00/10] net: phy: Add support for 2.5GBASET PHYs Heiner Kallweit
2019-02-09 16:25 ` Andrew Lunn
2019-02-09 16:28 ` Heiner Kallweit
2019-02-11 7:46 ` Maxime Chevallier
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190207094939.27369-1-maxime.chevallier@bootlin.com \
--to=maxime.chevallier@bootlin.com \
--cc=andrew@lunn.ch \
--cc=antoine.tenart@bootlin.com \
--cc=davem@davemloft.net \
--cc=f.fainelli@gmail.com \
--cc=gregory.clement@bootlin.com \
--cc=hkallweit1@gmail.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux@armlinux.org.uk \
--cc=miquel.raynal@bootlin.com \
--cc=mw@semihalf.com \
--cc=nadavh@marvell.com \
--cc=netdev@vger.kernel.org \
--cc=stefanc@marvell.com \
--cc=thomas.petazzoni@bootlin.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).