Netdev Archive on lore.kernel.org
 help / color / Atom feed
From: Alexandru Ardelean <alexandru.ardelean@analog.com>
To: <netdev@vger.kernel.org>, <devicetree@vger.kernel.org>,
	<linux-kernel@vger.kernel.org>
Cc: <davem@davemloft.net>, <robh+dt@kernel.org>,
	<mark.rutland@arm.com>, <f.fainelli@gmail.com>,
	<hkallweit1@gmail.com>, <andrew@lunn.ch>,
	Alexandru Ardelean <alexandru.ardelean@analog.com>
Subject: [PATCH v5 08/13] net: phy: adin: add support MDI/MDIX/Auto-MDI selection
Date: Fri, 16 Aug 2019 16:10:06 +0300
Message-ID: <20190816131011.23264-9-alexandru.ardelean@analog.com> (raw)
In-Reply-To: <20190816131011.23264-1-alexandru.ardelean@analog.com>

The ADIN PHYs support automatic MDI/MDIX negotiation. By default this is
disabled, so this is enabled at `config_init`.

This is controlled via the PHY Control 1 register.
The supported modes are:
  1. Manual MDI
  2. Manual MDIX
  3. Auto MDIX - prefer MDIX
  4. Auto MDIX - prefer MDI

The phydev mdix & mdix_ctrl fields include modes 3 & 4 into a single
auto-mode. So, the default mode this driver enables is 4 when Auto-MDI mode
is used.

When detecting MDI/MDIX mode, a combination of the PHY Control 1 register
and PHY Status 1 register is used to determine the correct MDI/MDIX mode.

If Auto-MDI mode is not set, then the manual MDI/MDIX mode is returned.
If Auto-MDI mode is set, then MDIX mode is returned differs from the
preferred MDI/MDIX mode.
This covers all cases where:
  1. MDI preferred  & Pair01Swapped   == MDIX
  2. MDIX preferred & Pair01Swapped   == MDI
  3. MDI preferred  & ! Pair01Swapped == MDIX
  4. MDIX preferred & ! Pair01Swapped == MDI

The preferred MDI/MDIX mode is not configured via SW, but can be configured
via HW pins. Note that the `Pair01Swapped` is the Green-Yellow physical
pairs.

Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
---
 drivers/net/phy/adin.c | 117 +++++++++++++++++++++++++++++++++++++++--
 1 file changed, 113 insertions(+), 4 deletions(-)

diff --git a/drivers/net/phy/adin.c b/drivers/net/phy/adin.c
index 4ca685780622..51c0d17577de 100644
--- a/drivers/net/phy/adin.c
+++ b/drivers/net/phy/adin.c
@@ -19,6 +19,10 @@
 #define ADIN1300_MII_EXT_REG_PTR		0x0010
 #define ADIN1300_MII_EXT_REG_DATA		0x0011
 
+#define ADIN1300_PHY_CTRL1			0x0012
+#define   ADIN1300_AUTO_MDI_EN			BIT(10)
+#define   ADIN1300_MAN_MDIX_EN			BIT(9)
+
 #define ADIN1300_INT_MASK_REG			0x0018
 #define   ADIN1300_INT_MDIO_SYNC_EN		BIT(9)
 #define   ADIN1300_INT_ANEG_STAT_CHNG_EN	BIT(8)
@@ -33,6 +37,9 @@
 	(ADIN1300_INT_LINK_STAT_CHNG_EN | ADIN1300_INT_HW_IRQ_EN)
 #define ADIN1300_INT_STATUS_REG			0x0019
 
+#define ADIN1300_PHY_STATUS1			0x001a
+#define   ADIN1300_PAIR_01_SWAP			BIT(11)
+
 #define ADIN1300_GE_RGMII_CFG_REG		0xff23
 #define   ADIN1300_GE_RGMII_RX_MSK		GENMASK(8, 6)
 #define   ADIN1300_GE_RGMII_RX_SEL(x)		\
@@ -206,6 +213,8 @@ static int adin_config_init(struct phy_device *phydev)
 {
 	int rc;
 
+	phydev->mdix_ctrl = ETH_TP_MDI_AUTO;
+
 	rc = genphy_config_init(phydev);
 	if (rc < 0)
 		return rc;
@@ -269,13 +278,113 @@ static int adin_write_mmd(struct phy_device *phydev, int devad, u16 regnum,
 	return __mdiobus_write(bus, phy_addr, ADIN1300_MII_EXT_REG_DATA, val);
 }
 
+static int adin_config_mdix(struct phy_device *phydev)
+{
+	bool auto_en, mdix_en;
+	int reg;
+
+	mdix_en = false;
+	auto_en = false;
+	switch (phydev->mdix_ctrl) {
+	case ETH_TP_MDI:
+		break;
+	case ETH_TP_MDI_X:
+		mdix_en = true;
+		break;
+	case ETH_TP_MDI_AUTO:
+		auto_en = true;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	reg = phy_read(phydev, ADIN1300_PHY_CTRL1);
+	if (reg < 0)
+		return reg;
+
+	if (mdix_en)
+		reg |= ADIN1300_MAN_MDIX_EN;
+	else
+		reg &= ~ADIN1300_MAN_MDIX_EN;
+
+	if (auto_en)
+		reg |= ADIN1300_AUTO_MDI_EN;
+	else
+		reg &= ~ADIN1300_AUTO_MDI_EN;
+
+	return phy_write(phydev, ADIN1300_PHY_CTRL1, reg);
+}
+
+static int adin_config_aneg(struct phy_device *phydev)
+{
+	int ret;
+
+	ret = adin_config_mdix(phydev);
+	if (ret)
+		return ret;
+
+	return genphy_config_aneg(phydev);
+}
+
+static int adin_mdix_update(struct phy_device *phydev)
+{
+	bool auto_en, mdix_en;
+	bool swapped;
+	int reg;
+
+	reg = phy_read(phydev, ADIN1300_PHY_CTRL1);
+	if (reg < 0)
+		return reg;
+
+	auto_en = !!(reg & ADIN1300_AUTO_MDI_EN);
+	mdix_en = !!(reg & ADIN1300_MAN_MDIX_EN);
+
+	/* If MDI/MDIX is forced, just read it from the control reg */
+	if (!auto_en) {
+		if (mdix_en)
+			phydev->mdix = ETH_TP_MDI_X;
+		else
+			phydev->mdix = ETH_TP_MDI;
+		return 0;
+	}
+
+	/**
+	 * Otherwise, we need to deduce it from the PHY status2 reg.
+	 * When Auto-MDI is enabled, the ADIN1300_MAN_MDIX_EN bit implies
+	 * a preference for MDIX when it is set.
+	 */
+	reg = phy_read(phydev, ADIN1300_PHY_STATUS1);
+	if (reg < 0)
+		return reg;
+
+	swapped = !!(reg & ADIN1300_PAIR_01_SWAP);
+
+	if (mdix_en != swapped)
+		phydev->mdix = ETH_TP_MDI_X;
+	else
+		phydev->mdix = ETH_TP_MDI;
+
+	return 0;
+}
+
+static int adin_read_status(struct phy_device *phydev)
+{
+	int ret;
+
+	ret = adin_mdix_update(phydev);
+	if (ret < 0)
+		return ret;
+
+	return genphy_read_status(phydev);
+}
+
 static struct phy_driver adin_driver[] = {
 	{
 		PHY_ID_MATCH_MODEL(PHY_ID_ADIN1200),
 		.name		= "ADIN1200",
 		.config_init	= adin_config_init,
-		.config_aneg	= genphy_config_aneg,
-		.read_status	= genphy_read_status,
+		.config_aneg	= adin_config_aneg,
+		.read_status	= adin_read_status,
 		.ack_interrupt	= adin_phy_ack_intr,
 		.config_intr	= adin_phy_config_intr,
 		.resume		= genphy_resume,
@@ -287,8 +396,8 @@ static struct phy_driver adin_driver[] = {
 		PHY_ID_MATCH_MODEL(PHY_ID_ADIN1300),
 		.name		= "ADIN1300",
 		.config_init	= adin_config_init,
-		.config_aneg	= genphy_config_aneg,
-		.read_status	= genphy_read_status,
+		.config_aneg	= adin_config_aneg,
+		.read_status	= adin_read_status,
 		.ack_interrupt	= adin_phy_ack_intr,
 		.config_intr	= adin_phy_config_intr,
 		.resume		= genphy_resume,
-- 
2.20.1


  parent reply index

Thread overview: 17+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-08-16 13:09 [PATCH v5 00/13] net: phy: adin: add support for Analog Devices PHYs Alexandru Ardelean
2019-08-16 13:09 ` [PATCH v5 01/13] " Alexandru Ardelean
2019-08-16 13:10 ` [PATCH v5 02/13] net: phy: adin: hook genphy_{suspend,resume} into the driver Alexandru Ardelean
2019-08-16 13:10 ` [PATCH v5 03/13] net: phy: adin: add support for interrupts Alexandru Ardelean
2019-08-16 13:10 ` [PATCH v5 04/13] net: phy: adin: add {write,read}_mmd hooks Alexandru Ardelean
2019-08-16 13:10 ` [PATCH v5 05/13] net: phy: adin: configure RGMII/RMII/MII modes on config Alexandru Ardelean
2019-08-16 13:10 ` [PATCH v5 06/13] net: phy: adin: make RGMII internal delays configurable Alexandru Ardelean
2019-08-16 13:10 ` [PATCH v5 07/13] net: phy: adin: make RMII fifo depth configurable Alexandru Ardelean
2019-08-16 13:10 ` Alexandru Ardelean [this message]
2019-08-16 13:10 ` [PATCH v5 09/13] net: phy: adin: add EEE translation layer from Clause 45 to Clause 22 Alexandru Ardelean
2019-08-16 13:10 ` [PATCH v5 10/13] net: phy: adin: implement PHY subsystem software reset Alexandru Ardelean
2019-08-16 13:19   ` Andrew Lunn
2019-08-16 13:10 ` [PATCH v5 11/13] net: phy: adin: implement downshift configuration via phy-tunable Alexandru Ardelean
2019-08-16 13:10 ` [PATCH v5 12/13] net: phy: adin: add ethtool get_stats support Alexandru Ardelean
2019-08-16 13:24   ` Andrew Lunn
2019-08-16 13:10 ` [PATCH v5 13/13] dt-bindings: net: add bindings for ADIN PHY driver Alexandru Ardelean
2019-08-16 18:57 ` [PATCH v5 00/13] net: phy: adin: add support for Analog Devices PHYs David Miller

Reply instructions:

You may reply publically to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20190816131011.23264-9-alexandru.ardelean@analog.com \
    --to=alexandru.ardelean@analog.com \
    --cc=andrew@lunn.ch \
    --cc=davem@davemloft.net \
    --cc=devicetree@vger.kernel.org \
    --cc=f.fainelli@gmail.com \
    --cc=hkallweit1@gmail.com \
    --cc=linux-kernel@vger.kernel.org \
    --cc=mark.rutland@arm.com \
    --cc=netdev@vger.kernel.org \
    --cc=robh+dt@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

Netdev Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/netdev/0 netdev/git/0.git
	git clone --mirror https://lore.kernel.org/netdev/1 netdev/git/1.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 netdev netdev/ https://lore.kernel.org/netdev \
		netdev@vger.kernel.org
	public-inbox-index netdev

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.netdev


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git