From: Andrew Jeffery <andrew@aj.id.au>
To: netdev@vger.kernel.org
Cc: davem@davemloft.net, robh+dt@kernel.org, mark.rutland@arm.com,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
joel@jms.id.au, benh@kernel.crashing.org
Subject: [PATCH 3/3] net: ftgmac100: Ungate RCLK for RMII on ASPEED MACs
Date: Tue, 8 Oct 2019 22:21:43 +1030 [thread overview]
Message-ID: <20191008115143.14149-4-andrew@aj.id.au> (raw)
In-Reply-To: <20191008115143.14149-1-andrew@aj.id.au>
The 50MHz RCLK has to be enabled before the RMII interface will function.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
---
drivers/net/ethernet/faraday/ftgmac100.c | 35 +++++++++++++++++++-----
1 file changed, 28 insertions(+), 7 deletions(-)
diff --git a/drivers/net/ethernet/faraday/ftgmac100.c b/drivers/net/ethernet/faraday/ftgmac100.c
index 9b7af94a40bb..9ff791fb0449 100644
--- a/drivers/net/ethernet/faraday/ftgmac100.c
+++ b/drivers/net/ethernet/faraday/ftgmac100.c
@@ -90,6 +90,9 @@ struct ftgmac100 {
struct mii_bus *mii_bus;
struct clk *clk;
+ /* 2600 RMII clock gate */
+ struct clk *rclk;
+
/* Link management */
int cur_speed;
int cur_duplex;
@@ -1718,12 +1721,14 @@ static void ftgmac100_ncsi_handler(struct ncsi_dev *nd)
nd->link_up ? "up" : "down");
}
-static void ftgmac100_setup_clk(struct ftgmac100 *priv)
+static int ftgmac100_setup_clk(struct ftgmac100 *priv)
{
- priv->clk = devm_clk_get(priv->dev, NULL);
- if (IS_ERR(priv->clk))
- return;
+ struct clk *clk;
+ clk = devm_clk_get(priv->dev, NULL /* MACCLK */);
+ if (IS_ERR(clk))
+ return PTR_ERR(clk);
+ priv->clk = clk;
clk_prepare_enable(priv->clk);
/* Aspeed specifies a 100MHz clock is required for up to
@@ -1732,6 +1737,14 @@ static void ftgmac100_setup_clk(struct ftgmac100 *priv)
*/
clk_set_rate(priv->clk, priv->use_ncsi ? FTGMAC_25MHZ :
FTGMAC_100MHZ);
+
+ /* RCLK is for RMII, typically used for NCSI. Optional because its not
+ * necessary if it's the 2400 MAC or the MAC is configured for RGMII
+ */
+ priv->rclk = devm_clk_get_optional(priv->dev, "RCLK");
+ clk_prepare_enable(priv->rclk);
+
+ return 0;
}
static int ftgmac100_probe(struct platform_device *pdev)
@@ -1853,8 +1866,11 @@ static int ftgmac100_probe(struct platform_device *pdev)
goto err_setup_mdio;
}
- if (priv->is_aspeed)
- ftgmac100_setup_clk(priv);
+ if (priv->is_aspeed) {
+ err = ftgmac100_setup_clk(priv);
+ if (err)
+ goto err_ncsi_dev;
+ }
/* Default ring sizes */
priv->rx_q_entries = priv->new_rx_q_entries = DEF_RX_QUEUE_ENTRIES;
@@ -1886,8 +1902,11 @@ static int ftgmac100_probe(struct platform_device *pdev)
return 0;
-err_ncsi_dev:
err_register_netdev:
+ if (priv->rclk)
+ clk_disable_unprepare(priv->rclk);
+ clk_disable_unprepare(priv->clk);
+err_ncsi_dev:
ftgmac100_destroy_mdio(netdev);
err_setup_mdio:
iounmap(priv->base);
@@ -1909,6 +1928,8 @@ static int ftgmac100_remove(struct platform_device *pdev)
unregister_netdev(netdev);
+ if (priv->rclk)
+ clk_disable_unprepare(priv->rclk);
clk_disable_unprepare(priv->clk);
/* There's a small chance the reset task will have been re-queued,
--
2.20.1
next prev parent reply other threads:[~2019-10-08 11:50 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-10-08 11:51 [PATCH 0/3] net: ftgmac100: Ungate RCLK for RMII on ASPEED MACs Andrew Jeffery
2019-10-08 11:51 ` [PATCH 1/3] dt-bindings: net: ftgmac100: Document AST2600 compatible Andrew Jeffery
2019-10-08 12:40 ` Joel Stanley
2019-10-09 4:38 ` Benjamin Herrenschmidt
2019-10-09 4:49 ` Andrew Jeffery
2019-10-09 4:55 ` Andrew Jeffery
2019-10-10 0:10 ` Benjamin Herrenschmidt
2019-10-08 11:51 ` [PATCH 2/3] dt-bindings: net: ftgmac100: Describe clock properties Andrew Jeffery
2019-10-08 12:42 ` Joel Stanley
2019-10-09 0:19 ` Andrew Jeffery
2019-10-08 11:51 ` Andrew Jeffery [this message]
2019-10-08 12:44 ` [PATCH 3/3] net: ftgmac100: Ungate RCLK for RMII on ASPEED MACs Joel Stanley
2019-10-09 0:38 ` [PATCH 0/3] " Florian Fainelli
2019-10-09 1:11 ` Joel Stanley
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20191008115143.14149-4-andrew@aj.id.au \
--to=andrew@aj.id.au \
--cc=benh@kernel.crashing.org \
--cc=davem@davemloft.net \
--cc=devicetree@vger.kernel.org \
--cc=joel@jms.id.au \
--cc=linux-kernel@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=netdev@vger.kernel.org \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).