From: Dan Murphy <dmurphy@ti.com>
To: <andrew@lunn.ch>, <f.fainelli@gmail.com>, <hkallweit1@gmail.com>,
<davem@davemloft.net>
Cc: <netdev@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
Dan Murphy <dmurphy@ti.com>, Rob Herring <robh+dt@kernel.org>
Subject: [PATCH 1/2] dt-bindings: net: dp83869: Add TI dp83869 phy
Date: Tue, 5 Nov 2019 12:18:25 -0600 [thread overview]
Message-ID: <20191105181826.25114-1-dmurphy@ti.com> (raw)
Add dt bindings for the TI dp83869 Gigabit ethernet phy
device.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
CC: Rob Herring <robh+dt@kernel.org>
---
.../devicetree/bindings/net/ti,dp83869.yaml | 84 +++++++++++++++++++
1 file changed, 84 insertions(+)
create mode 100644 Documentation/devicetree/bindings/net/ti,dp83869.yaml
diff --git a/Documentation/devicetree/bindings/net/ti,dp83869.yaml b/Documentation/devicetree/bindings/net/ti,dp83869.yaml
new file mode 100644
index 000000000000..6fe3e451da8a
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/ti,dp83869.yaml
@@ -0,0 +1,84 @@
+# SPDX-License-Identifier: GPL-2.0
+# Copyright (C) 2019 Texas Instruments Incorporated
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/net/ti,dp83869.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: TI DP83869 ethernet PHY
+
+allOf:
+ - $ref: "ethernet-controller.yaml#"
+
+maintainers:
+ - Dan Murphy <dmurphy@ti.com>
+
+description: |
+ The DP83869HM device is a robust, fully-featured Gigabit (PHY) transceiver
+ with integrated PMD sublayers that supports 10BASE-Te, 100BASE-TX and
+ 1000BASE-T Ethernet protocols. The DP83869 also supports 1000BASE-X and
+ 100BASE-FX Fiber protocols.
+ This device interfaces to the MAC layer through Reduced GMII (RGMII) and
+ SGMII The DP83869HM supports Media Conversion in Managed mode. In this mode,
+ the DP83869HM can run 1000BASE-X-to-1000BASE-T and 100BASE-FX-to-100BASE-TX
+ conversions. The DP83869HM can also support Bridge Conversion from RGMII to
+ SGMII and SGMII to RGMII.
+
+ Specifications about the charger can be found at:
+ http://www.ti.com/lit/ds/symlink/dp83869hm.pdf
+
+properties:
+ reg:
+ maxItems: 1
+
+ ti,min-output-impedance:
+ type: boolean
+ description: |
+ MAC Interface Impedance control to set the programmable output impedance
+ to a minimum value (35 ohms).
+
+ ti,max-output-impedance:
+ type: boolean
+ description: |
+ MAC Interface Impedance control to set the programmable output impedance
+ to a maximum value (70 ohms).
+
+ tx-fifo-depth:
+ $ref: /schemas/types.yaml#definitions/uint32
+ description: |
+ Transmitt FIFO depth see dt-bindings/net/ti-dp83869.h for values
+
+ rx-fifo-depth:
+ $ref: /schemas/types.yaml#definitions/uint32
+ description: |
+ Receive FIFO depth see dt-bindings/net/ti-dp83869.h for values
+
+ ti,clk-output-sel:
+ $ref: /schemas/types.yaml#definitions/uint32
+ description: |
+ Muxing option for CLK_OUT pin see dt-bindings/net/ti-dp83869.h for values.
+
+ ti,op-mode:
+ $ref: /schemas/types.yaml#definitions/uint32
+ description: |
+ Operational mode for the PHY. If this is not set then the operational
+ mode is set by the straps. see dt-bindings/net/ti-dp83869.h for values
+
+required:
+ - reg
+
+examples:
+ - |
+ #include <dt-bindings/net/ti-dp83869.h>
+ mdio0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ ethphy0: ethernet-phy@0 {
+ reg = <0>;
+ tx-fifo-depth = <DP83869_PHYCR_FIFO_DEPTH_4_B_NIB>;
+ rx-fifo-depth = <DP83869_PHYCR_FIFO_DEPTH_4_B_NIB>;
+ ti,op-mode = <DP83869_RGMII_COPPER_ETHERNET>;
+ ti,max-output-impedance = "true";
+ ti,clk-output-sel = <DP83869_CLK_O_SEL_CHN_A_RCLK>;
+ };
+ };
--
2.22.0.214.g8dca754b1e
next reply other threads:[~2019-11-05 18:19 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-11-05 18:18 Dan Murphy [this message]
2019-11-05 18:18 ` [PATCH 2/2] net: phy: dp83869: Add TI dp83869 phy Dan Murphy
2019-11-05 19:55 ` Heiner Kallweit
2019-11-05 20:02 ` Dan Murphy
2019-11-05 20:05 ` Florian Fainelli
2019-11-05 20:08 ` Dan Murphy
2019-11-05 20:20 ` Heiner Kallweit
2019-11-05 20:26 ` Dan Murphy
2019-11-05 20:48 ` Heiner Kallweit
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20191105181826.25114-1-dmurphy@ti.com \
--to=dmurphy@ti.com \
--cc=andrew@lunn.ch \
--cc=davem@davemloft.net \
--cc=f.fainelli@gmail.com \
--cc=hkallweit1@gmail.com \
--cc=linux-kernel@vger.kernel.org \
--cc=netdev@vger.kernel.org \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).