[PATCH net-next v3 00/12] ethtool: consolidate parameter checking for irq coalescing

[PATCH net-next v3 00/12] ethtool: consolidate parameter checking for irq coalescing

[Jakub Kicinski]

Hi!

This set aims to simplify and unify the unsupported irq
coalescing parameter handling.

First patch adds a bitmask which drivers should fill in
in their ethtool_ops structs to declare which parameters
they support. Core will then ensure that driver callback
won't see any parameter outside of that set.

This allows us to save some LoC and make sure all drivers
respond the same to unsupported parameters.

If any parameter driver does not support is set to a value
other than 0 core will return -EINVAL. In the future we can
reject any present but unsupported netlink attribute, without
assuming 0 means unset. We can also add some prints or extack,
perhaps a'la Intel's current code.

I started converting the drivers alphabetically but then
realized that for the first set it's probably best to
address a representative mix of actively developed drivers.

According to my unreliable math there are roughly 69 drivers
in the tree which support some form of interrupt coalescing
settings via ethtool. Of these roughly 17 reject parameters
they don't support.

I hope drivers which ignore the parameters don't care, and
won't care about the slight change in behavior. Once all
drivers are converted we can make the checking mandatory.

I've only tested the e1000e and virtio patches, the rest builds.

v2: fix up ice and virtio conversions
v3: (patch 1)
    - move the (temporary) check if driver defines types
      earlier (Michal)
    - rename used_types -> nonzero_params, and
      coalesce_types -> supported_coalesce_params (Alex)
    - use EOPNOTSUPP instead of EINVAL (Andrew, Michal)

Jakub Kicinski (12):
  ethtool: add infrastructure for centralized checking of coalescing
    parameters
  xgbe: let core reject the unsupported coalescing parameters
  enic: let core reject the unsupported coalescing parameters
  stmmac: let core reject the unsupported coalescing parameters
  nfp: let core reject the unsupported coalescing parameters
  ionic: let core reject the unsupported coalescing parameters
  hisilicon: let core reject the unsupported coalescing parameters
  ice: let core reject the unsupported coalescing parameters
  bnxt: reject unsupported coalescing params
  mlx5: reject unsupported coalescing params
  e1000e: reject unsupported coalescing params
  virtio_net: reject unsupported coalescing params

 drivers/net/ethernet/amd/xgbe/xgbe-ethtool.c  | 26 +-------
 .../net/ethernet/broadcom/bnxt/bnxt_ethtool.c |  6 ++
 .../net/ethernet/cisco/enic/enic_ethtool.c    | 23 ++-----
 drivers/net/ethernet/hisilicon/hip04_eth.c    | 16 +----
 drivers/net/ethernet/intel/e1000e/ethtool.c   |  1 +
 drivers/net/ethernet/intel/ice/ice_ethtool.c  | 59 +----------------
 .../ethernet/mellanox/mlx5/core/en_ethtool.c  |  3 +
 .../net/ethernet/mellanox/mlx5/core/en_rep.c  |  6 ++
 .../mellanox/mlx5/core/ipoib/ethtool.c        |  3 +
 .../ethernet/netronome/nfp/nfp_net_ethtool.c  | 22 +------
 .../ethernet/pensando/ionic/ionic_ethtool.c   | 23 +------
 .../ethernet/stmicro/stmmac/stmmac_ethtool.c  | 16 +----
 drivers/net/virtio_net.c                      | 14 +---
 include/linux/ethtool.h                       | 45 ++++++++++++-
 net/ethtool/ioctl.c                           | 66 +++++++++++++++++++
 15 files changed, 146 insertions(+), 183 deletions(-)

-- 
2.24.1

[PATCH net-next v3 01/12] ethtool: add infrastructure for centralized checking of coalescing parameters

[Jakub Kicinski]

Linux supports 22 different interrupt coalescing parameters.
No driver implements them all. Some drivers just ignore the
ones they don't support, while others have to carry a long
list of checks to reject unsupported settings.

To simplify the drivers add the ability to specify inside
ethtool_ops which parameters are supported and let the core
reject attempts to set any other one.

This commit makes the mechanism an opt-in, only drivers which
set ethtool_opts->coalesce_types to a non-zero value will have
the checks enforced.

The same mask is used for global and per queue settings.

v3: - move the (temporary) check if driver defines types
      earlier (Michal)
    - rename used_types -> nonzero_params, and
      coalesce_types -> supported_coalesce_params (Alex)
    - use EOPNOTSUPP instead of EINVAL (Andrew, Michal)

Leaving the long series of ifs for now, it seems nice to
be able to grep for the field and flag names. This will
probably have to be revisited once netlink support lands.

Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
---
 include/linux/ethtool.h | 45 ++++++++++++++++++++++++++--
 net/ethtool/ioctl.c     | 66 +++++++++++++++++++++++++++++++++++++++++
 2 files changed, 108 insertions(+), 3 deletions(-)

diff --git a/include/linux/ethtool.h b/include/linux/ethtool.h
index 23373978cb3c..e464c946bca4 100644
--- a/include/linux/ethtool.h
+++ b/include/linux/ethtool.h
@@ -177,8 +177,44 @@ void ethtool_convert_legacy_u32_to_link_mode(unsigned long *dst,
 bool ethtool_convert_link_mode_to_legacy_u32(u32 *legacy_u32,
 				     const unsigned long *src);
 
+#define ETHTOOL_COALESCE_RX_USECS		BIT(0)
+#define ETHTOOL_COALESCE_RX_MAX_FRAMES		BIT(1)
+#define ETHTOOL_COALESCE_RX_USECS_IRQ		BIT(2)
+#define ETHTOOL_COALESCE_RX_MAX_FRAMES_IRQ	BIT(3)
+#define ETHTOOL_COALESCE_TX_USECS		BIT(4)
+#define ETHTOOL_COALESCE_TX_MAX_FRAMES		BIT(5)
+#define ETHTOOL_COALESCE_TX_USECS_IRQ		BIT(6)
+#define ETHTOOL_COALESCE_TX_MAX_FRAMES_IRQ	BIT(7)
+#define ETHTOOL_COALESCE_STATS_BLOCK_USECS	BIT(8)
+#define ETHTOOL_COALESCE_USE_ADAPTIVE_RX	BIT(9)
+#define ETHTOOL_COALESCE_USE_ADAPTIVE_TX	BIT(10)
+#define ETHTOOL_COALESCE_PKT_RATE_LOW		BIT(11)
+#define ETHTOOL_COALESCE_RX_USECS_LOW		BIT(12)
+#define ETHTOOL_COALESCE_RX_MAX_FRAMES_LOW	BIT(13)
+#define ETHTOOL_COALESCE_TX_USECS_LOW		BIT(14)
+#define ETHTOOL_COALESCE_TX_MAX_FRAMES_LOW	BIT(15)
+#define ETHTOOL_COALESCE_PKT_RATE_HIGH		BIT(16)
+#define ETHTOOL_COALESCE_RX_USECS_HIGH		BIT(17)
+#define ETHTOOL_COALESCE_RX_MAX_FRAMES_HIGH	BIT(18)
+#define ETHTOOL_COALESCE_TX_USECS_HIGH		BIT(19)
+#define ETHTOOL_COALESCE_TX_MAX_FRAMES_HIGH	BIT(20)
+#define ETHTOOL_COALESCE_RATE_SAMPLE_INTERVAL	BIT(21)
+
+#define ETHTOOL_COALESCE_USECS						\
+	(ETHTOOL_COALESCE_RX_USECS | ETHTOOL_COALESCE_TX_USECS)
+#define ETHTOOL_COALESCE_MAX_FRAMES					\
+	(ETHTOOL_COALESCE_RX_MAX_FRAMES | ETHTOOL_COALESCE_TX_MAX_FRAMES)
+#define ETHTOOL_COALESCE_USECS_IRQ					\
+	(ETHTOOL_COALESCE_RX_USECS_IRQ | ETHTOOL_COALESCE_TX_USECS_IRQ)
+#define ETHTOOL_COALESCE_MAX_FRAMES_IRQ		\
+	(ETHTOOL_COALESCE_RX_MAX_FRAMES_IRQ |	\
+	 ETHTOOL_COALESCE_TX_MAX_FRAMES_IRQ)
+#define ETHTOOL_COALESCE_USE_ADAPTIVE					\
+	(ETHTOOL_COALESCE_USE_ADAPTIVE_RX | ETHTOOL_COALESCE_USE_ADAPTIVE_TX)
+
 /**
  * struct ethtool_ops - optional netdev operations
+ * @supported_coalesce_params: supported types of interrupt coalescing.
  * @get_drvinfo: Report driver/device information.  Should only set the
  *	@driver, @version, @fw_version and @bus_info fields.  If not
  *	implemented, the @driver and @bus_info fields will be filled in
@@ -207,8 +243,9 @@ bool ethtool_convert_link_mode_to_legacy_u32(u32 *legacy_u32,
  *	or zero.
  * @get_coalesce: Get interrupt coalescing parameters.  Returns a negative
  *	error code or zero.
- * @set_coalesce: Set interrupt coalescing parameters.  Returns a negative
- *	error code or zero.
+ * @set_coalesce: Set interrupt coalescing parameters.  Supported coalescing
+ *	types should be set in @supported_coalesce_params.
+ *	Returns a negative error code or zero.
  * @get_ringparam: Report ring sizes
  * @set_ringparam: Set ring sizes.  Returns a negative error code or zero.
  * @get_pauseparam: Report pause parameters
@@ -292,7 +329,8 @@ bool ethtool_convert_link_mode_to_legacy_u32(u32 *legacy_u32,
  * @set_per_queue_coalesce: Set interrupt coalescing parameters per queue.
  *	It must check that the given queue number is valid. If neither a RX nor
  *	a TX queue has this number, return -EINVAL. If only a RX queue or a TX
- *	queue has this number, ignore the inapplicable fields.
+ *	queue has this number, ignore the inapplicable fields. Supported
+ *	coalescing types should be set in @supported_coalesce_params.
  *	Returns a negative error code or zero.
  * @get_link_ksettings: Get various device settings including Ethernet link
  *	settings. The %cmd and %link_mode_masks_nwords fields should be
@@ -323,6 +361,7 @@ bool ethtool_convert_link_mode_to_legacy_u32(u32 *legacy_u32,
  * of the generic netdev features interface.
  */
 struct ethtool_ops {
+	u32	supported_coalesce_params;
 	void	(*get_drvinfo)(struct net_device *, struct ethtool_drvinfo *);
 	int	(*get_regs_len)(struct net_device *);
 	void	(*get_regs)(struct net_device *, struct ethtool_regs *, void *);
diff --git a/net/ethtool/ioctl.c b/net/ethtool/ioctl.c
index f2fe8e5896dc..b2684ffa26de 100644
--- a/net/ethtool/ioctl.c
+++ b/net/ethtool/ioctl.c
@@ -1544,6 +1544,64 @@ static noinline_for_stack int ethtool_get_coalesce(struct net_device *dev,
 	return 0;
 }
 
+static bool
+ethtool_set_coalesce_supported(struct net_device *dev,
+			       struct ethtool_coalesce *coalesce)
+{
+	u32 supported_params = dev->ethtool_ops->supported_coalesce_params;
+	u32 nonzero_params = 0;
+
+	if (!supported_params)
+		return true;
+
+	if (coalesce->rx_coalesce_usecs)
+		nonzero_params |= ETHTOOL_COALESCE_RX_USECS;
+	if (coalesce->rx_max_coalesced_frames)
+		nonzero_params |= ETHTOOL_COALESCE_RX_MAX_FRAMES;
+	if (coalesce->rx_coalesce_usecs_irq)
+		nonzero_params |= ETHTOOL_COALESCE_RX_USECS_IRQ;
+	if (coalesce->rx_max_coalesced_frames_irq)
+		nonzero_params |= ETHTOOL_COALESCE_RX_MAX_FRAMES_IRQ;
+	if (coalesce->tx_coalesce_usecs)
+		nonzero_params |= ETHTOOL_COALESCE_TX_USECS;
+	if (coalesce->tx_max_coalesced_frames)
+		nonzero_params |= ETHTOOL_COALESCE_TX_MAX_FRAMES;
+	if (coalesce->tx_coalesce_usecs_irq)
+		nonzero_params |= ETHTOOL_COALESCE_TX_USECS_IRQ;
+	if (coalesce->tx_max_coalesced_frames_irq)
+		nonzero_params |= ETHTOOL_COALESCE_TX_MAX_FRAMES_IRQ;
+	if (coalesce->stats_block_coalesce_usecs)
+		nonzero_params |= ETHTOOL_COALESCE_STATS_BLOCK_USECS;
+	if (coalesce->use_adaptive_rx_coalesce)
+		nonzero_params |= ETHTOOL_COALESCE_USE_ADAPTIVE_RX;
+	if (coalesce->use_adaptive_tx_coalesce)
+		nonzero_params |= ETHTOOL_COALESCE_USE_ADAPTIVE_TX;
+	if (coalesce->pkt_rate_low)
+		nonzero_params |= ETHTOOL_COALESCE_PKT_RATE_LOW;
+	if (coalesce->rx_coalesce_usecs_low)
+		nonzero_params |= ETHTOOL_COALESCE_RX_USECS_LOW;
+	if (coalesce->rx_max_coalesced_frames_low)
+		nonzero_params |= ETHTOOL_COALESCE_RX_MAX_FRAMES_LOW;
+	if (coalesce->tx_coalesce_usecs_low)
+		nonzero_params |= ETHTOOL_COALESCE_TX_USECS_LOW;
+	if (coalesce->tx_max_coalesced_frames_low)
+		nonzero_params |= ETHTOOL_COALESCE_TX_MAX_FRAMES_LOW;
+	if (coalesce->pkt_rate_high)
+		nonzero_params |= ETHTOOL_COALESCE_PKT_RATE_HIGH;
+	if (coalesce->rx_coalesce_usecs_high)
+		nonzero_params |= ETHTOOL_COALESCE_RX_USECS_HIGH;
+	if (coalesce->rx_max_coalesced_frames_high)
+		nonzero_params |= ETHTOOL_COALESCE_RX_MAX_FRAMES_HIGH;
+	if (coalesce->tx_coalesce_usecs_high)
+		nonzero_params |= ETHTOOL_COALESCE_TX_USECS_HIGH;
+	if (coalesce->tx_max_coalesced_frames_high)
+		nonzero_params |= ETHTOOL_COALESCE_TX_MAX_FRAMES_HIGH;
+	if (coalesce->rate_sample_interval)
+		nonzero_params |= ETHTOOL_COALESCE_RATE_SAMPLE_INTERVAL;
+
+	return (supported_params & nonzero_params) == nonzero_params;
+}
+
 static noinline_for_stack int ethtool_set_coalesce(struct net_device *dev,
 						   void __user *useraddr)
 {
@@ -1555,6 +1613,9 @@ static noinline_for_stack int ethtool_set_coalesce(struct net_device *dev,
 	if (copy_from_user(&coalesce, useraddr, sizeof(coalesce)))
 		return -EFAULT;
 
+	if (!ethtool_set_coalesce_supported(dev, &coalesce))
+		return -EOPNOTSUPP;
+
 	return dev->ethtool_ops->set_coalesce(dev, &coalesce);
 }
 
@@ -2336,6 +2397,11 @@ ethtool_set_per_queue_coalesce(struct net_device *dev,
 			goto roll_back;
 		}
 
+		if (!ethtool_set_coalesce_supported(dev, &coalesce)) {
+			ret = -EOPNOTSUPP;
+			goto roll_back;
+		}
+
 		ret = dev->ethtool_ops->set_per_queue_coalesce(dev, bit, &coalesce);
 		if (ret != 0)
 			goto roll_back;
-- 
2.24.1

[PATCH net-next v3 02/12] xgbe: let core reject the unsupported coalescing parameters

[Jakub Kicinski]

Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.

This driver correctly rejects all unsupported parameters.
We are only losing the error print.

v3: adjust commit message for new error code and member name

Signed-off-by: Jakub Kicinski <kuba@kernel.org>
---
 drivers/net/ethernet/amd/xgbe/xgbe-ethtool.c | 26 ++------------------
 1 file changed, 2 insertions(+), 24 deletions(-)

diff --git a/drivers/net/ethernet/amd/xgbe/xgbe-ethtool.c b/drivers/net/ethernet/amd/xgbe/xgbe-ethtool.c
index b23c8ee24ee3..61f39a0e04f9 100644
--- a/drivers/net/ethernet/amd/xgbe/xgbe-ethtool.c
+++ b/drivers/net/ethernet/amd/xgbe/xgbe-ethtool.c
@@ -450,30 +450,6 @@ static int xgbe_set_coalesce(struct net_device *netdev,
 	unsigned int rx_frames, rx_riwt, rx_usecs;
 	unsigned int tx_frames;
 
-	/* Check for not supported parameters  */
-	if ((ec->rx_coalesce_usecs_irq) ||
-	    (ec->rx_max_coalesced_frames_irq) ||
-	    (ec->tx_coalesce_usecs) ||
-	    (ec->tx_coalesce_usecs_irq) ||
-	    (ec->tx_max_coalesced_frames_irq) ||
-	    (ec->stats_block_coalesce_usecs) ||
-	    (ec->use_adaptive_rx_coalesce) ||
-	    (ec->use_adaptive_tx_coalesce) ||
-	    (ec->pkt_rate_low) ||
-	    (ec->rx_coalesce_usecs_low) ||
-	    (ec->rx_max_coalesced_frames_low) ||
-	    (ec->tx_coalesce_usecs_low) ||
-	    (ec->tx_max_coalesced_frames_low) ||
-	    (ec->pkt_rate_high) ||
-	    (ec->rx_coalesce_usecs_high) ||
-	    (ec->rx_max_coalesced_frames_high) ||
-	    (ec->tx_coalesce_usecs_high) ||
-	    (ec->tx_max_coalesced_frames_high) ||
-	    (ec->rate_sample_interval)) {
-		netdev_err(netdev, "unsupported coalescing parameter\n");
-		return -EOPNOTSUPP;
-	}
-
 	rx_riwt = hw_if->usec_to_riwt(pdata, ec->rx_coalesce_usecs);
 	rx_usecs = ec->rx_coalesce_usecs;
 	rx_frames = ec->rx_max_coalesced_frames;
@@ -837,6 +813,8 @@ static int xgbe_set_channels(struct net_device *netdev,
 }
 
 static const struct ethtool_ops xgbe_ethtool_ops = {
+	.supported_coalesce_params = ETHTOOL_COALESCE_RX_USECS |
+				     ETHTOOL_COALESCE_MAX_FRAMES,
 	.get_drvinfo = xgbe_get_drvinfo,
 	.get_msglevel = xgbe_get_msglevel,
 	.set_msglevel = xgbe_set_msglevel,
-- 
2.24.1

[PATCH net-next v3 03/12] enic: let core reject the unsupported coalescing parameters

[Jakub Kicinski]

Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.

This driver correctly rejects all unsupported parameters.
The error code changes from EINVAL to EOPNOTSUPP.

v3: adjust commit message for new error code and member name

Signed-off-by: Jakub Kicinski <kuba@kernel.org>
---
 .../net/ethernet/cisco/enic/enic_ethtool.c    | 23 ++++---------------
 1 file changed, 4 insertions(+), 19 deletions(-)

diff --git a/drivers/net/ethernet/cisco/enic/enic_ethtool.c b/drivers/net/ethernet/cisco/enic/enic_ethtool.c
index 84ff0e6ec33e..4d8e0aa447fb 100644
--- a/drivers/net/ethernet/cisco/enic/enic_ethtool.c
+++ b/drivers/net/ethernet/cisco/enic/enic_ethtool.c
@@ -323,25 +323,6 @@ static int enic_coalesce_valid(struct enic *enic,
 	u32 rx_coalesce_usecs_low = min_t(u32, coalesce_usecs_max,
 					  ec->rx_coalesce_usecs_low);
 
-	if (ec->rx_max_coalesced_frames		||
-	    ec->rx_coalesce_usecs_irq		||
-	    ec->rx_max_coalesced_frames_irq	||
-	    ec->tx_max_coalesced_frames		||
-	    ec->tx_coalesce_usecs_irq		||
-	    ec->tx_max_coalesced_frames_irq	||
-	    ec->stats_block_coalesce_usecs	||
-	    ec->use_adaptive_tx_coalesce	||
-	    ec->pkt_rate_low			||
-	    ec->rx_max_coalesced_frames_low	||
-	    ec->tx_coalesce_usecs_low		||
-	    ec->tx_max_coalesced_frames_low	||
-	    ec->pkt_rate_high			||
-	    ec->rx_max_coalesced_frames_high	||
-	    ec->tx_coalesce_usecs_high		||
-	    ec->tx_max_coalesced_frames_high	||
-	    ec->rate_sample_interval)
-		return -EINVAL;
-
 	if ((vnic_dev_get_intr_mode(enic->vdev) != VNIC_DEV_INTR_MODE_MSIX) &&
 	    ec->tx_coalesce_usecs)
 		return -EINVAL;
@@ -635,6 +616,10 @@ static int enic_get_ts_info(struct net_device *netdev,
 }
 
 static const struct ethtool_ops enic_ethtool_ops = {
+	.supported_coalesce_params = ETHTOOL_COALESCE_USECS |
+				     ETHTOOL_COALESCE_USE_ADAPTIVE_RX |
+				     ETHTOOL_COALESCE_RX_USECS_LOW |
+				     ETHTOOL_COALESCE_RX_USECS_HIGH,
 	.get_drvinfo = enic_get_drvinfo,
 	.get_msglevel = enic_get_msglevel,
 	.set_msglevel = enic_set_msglevel,
-- 
2.24.1

[PATCH net-next v3 04/12] stmmac: let core reject the unsupported coalescing parameters

[Jakub Kicinski]

Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.

This driver correctly rejects all unsupported parameters.
No functional changes.

v3: adjust commit message for new error code and member name

Signed-off-by: Jakub Kicinski <kuba@kernel.org>
---
 .../net/ethernet/stmicro/stmmac/stmmac_ethtool.c | 16 ++--------------
 1 file changed, 2 insertions(+), 14 deletions(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c
index b29603ec744c..eae11c585025 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c
@@ -732,20 +732,6 @@ static int stmmac_set_coalesce(struct net_device *dev,
 	u32 rx_cnt = priv->plat->rx_queues_to_use;
 	unsigned int rx_riwt;
 
-	/* Check not supported parameters  */
-	if ((ec->rx_coalesce_usecs_irq) ||
-	    (ec->rx_max_coalesced_frames_irq) || (ec->tx_coalesce_usecs_irq) ||
-	    (ec->use_adaptive_rx_coalesce) || (ec->use_adaptive_tx_coalesce) ||
-	    (ec->pkt_rate_low) || (ec->rx_coalesce_usecs_low) ||
-	    (ec->rx_max_coalesced_frames_low) || (ec->tx_coalesce_usecs_high) ||
-	    (ec->tx_max_coalesced_frames_low) || (ec->pkt_rate_high) ||
-	    (ec->tx_coalesce_usecs_low) || (ec->rx_coalesce_usecs_high) ||
-	    (ec->rx_max_coalesced_frames_high) ||
-	    (ec->tx_max_coalesced_frames_irq) ||
-	    (ec->stats_block_coalesce_usecs) ||
-	    (ec->tx_max_coalesced_frames_high) || (ec->rate_sample_interval))
-		return -EOPNOTSUPP;
-
 	if (priv->use_riwt && (ec->rx_coalesce_usecs > 0)) {
 		rx_riwt = stmmac_usec2riwt(ec->rx_coalesce_usecs, priv);
 
@@ -914,6 +900,8 @@ static int stmmac_set_tunable(struct net_device *dev,
 }
 
 static const struct ethtool_ops stmmac_ethtool_ops = {
+	.supported_coalesce_params = ETHTOOL_COALESCE_USECS |
+				     ETHTOOL_COALESCE_MAX_FRAMES,
 	.begin = stmmac_check_if_running,
 	.get_drvinfo = stmmac_ethtool_getdrvinfo,
 	.get_msglevel = stmmac_ethtool_getmsglevel,
-- 
2.24.1

[PATCH net-next v3 05/12] nfp: let core reject the unsupported coalescing parameters

[Jakub Kicinski]

Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.

This driver correctly rejects all unsupported parameters.
No functional changes.

v3: adjust commit message for new error code and member name

Signed-off-by: Jakub Kicinski <kuba@kernel.org>
---
 .../ethernet/netronome/nfp/nfp_net_ethtool.c  | 22 ++-----------------
 1 file changed, 2 insertions(+), 20 deletions(-)

diff --git a/drivers/net/ethernet/netronome/nfp/nfp_net_ethtool.c b/drivers/net/ethernet/netronome/nfp/nfp_net_ethtool.c
index d648e32c0520..2779f1526d1e 100644
--- a/drivers/net/ethernet/netronome/nfp/nfp_net_ethtool.c
+++ b/drivers/net/ethernet/netronome/nfp/nfp_net_ethtool.c
@@ -1343,26 +1343,6 @@ static int nfp_net_set_coalesce(struct net_device *netdev,
 	struct nfp_net *nn = netdev_priv(netdev);
 	unsigned int factor;
 
-	if (ec->rx_coalesce_usecs_irq ||
-	    ec->rx_max_coalesced_frames_irq ||
-	    ec->tx_coalesce_usecs_irq ||
-	    ec->tx_max_coalesced_frames_irq ||
-	    ec->stats_block_coalesce_usecs ||
-	    ec->use_adaptive_rx_coalesce ||
-	    ec->use_adaptive_tx_coalesce ||
-	    ec->pkt_rate_low ||
-	    ec->rx_coalesce_usecs_low ||
-	    ec->rx_max_coalesced_frames_low ||
-	    ec->tx_coalesce_usecs_low ||
-	    ec->tx_max_coalesced_frames_low ||
-	    ec->pkt_rate_high ||
-	    ec->rx_coalesce_usecs_high ||
-	    ec->rx_max_coalesced_frames_high ||
-	    ec->tx_coalesce_usecs_high ||
-	    ec->tx_max_coalesced_frames_high ||
-	    ec->rate_sample_interval)
-		return -EOPNOTSUPP;
-
 	/* Compute factor used to convert coalesce '_usecs' parameters to
 	 * ME timestamp ticks.  There are 16 ME clock cycles for each timestamp
 	 * count.
@@ -1476,6 +1456,8 @@ static int nfp_net_set_channels(struct net_device *netdev,
 }
 
 static const struct ethtool_ops nfp_net_ethtool_ops = {
+	.supported_coalesce_params = ETHTOOL_COALESCE_USECS |
+				     ETHTOOL_COALESCE_MAX_FRAMES,
 	.get_drvinfo		= nfp_net_get_drvinfo,
 	.get_link		= ethtool_op_get_link,
 	.get_ringparam		= nfp_net_get_ringparam,
-- 
2.24.1

[PATCH net-next v3 06/12] ionic: let core reject the unsupported coalescing parameters

[Jakub Kicinski]

Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.

This driver correctly rejects all unsupported parameters.
As a side effect of these changes the error code for
unsupported params changes from EINVAL to EOPNOTSUPP.

v3: adjust commit message for new error code and member name

Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Shannon Nelson <snelson@pensando.io>
---
 .../ethernet/pensando/ionic/ionic_ethtool.c   | 23 +------------------
 1 file changed, 1 insertion(+), 22 deletions(-)

diff --git a/drivers/net/ethernet/pensando/ionic/ionic_ethtool.c b/drivers/net/ethernet/pensando/ionic/ionic_ethtool.c
index f778fff034f5..b3a113a15ab1 100644
--- a/drivers/net/ethernet/pensando/ionic/ionic_ethtool.c
+++ b/drivers/net/ethernet/pensando/ionic/ionic_ethtool.c
@@ -412,28 +412,6 @@ static int ionic_set_coalesce(struct net_device *netdev,
 	unsigned int i;
 	u32 coal;
 
-	if (coalesce->rx_max_coalesced_frames ||
-	    coalesce->rx_coalesce_usecs_irq ||
-	    coalesce->rx_max_coalesced_frames_irq ||
-	    coalesce->tx_max_coalesced_frames ||
-	    coalesce->tx_coalesce_usecs_irq ||
-	    coalesce->tx_max_coalesced_frames_irq ||
-	    coalesce->stats_block_coalesce_usecs ||
-	    coalesce->use_adaptive_rx_coalesce ||
-	    coalesce->use_adaptive_tx_coalesce ||
-	    coalesce->pkt_rate_low ||
-	    coalesce->rx_coalesce_usecs_low ||
-	    coalesce->rx_max_coalesced_frames_low ||
-	    coalesce->tx_coalesce_usecs_low ||
-	    coalesce->tx_max_coalesced_frames_low ||
-	    coalesce->pkt_rate_high ||
-	    coalesce->rx_coalesce_usecs_high ||
-	    coalesce->rx_max_coalesced_frames_high ||
-	    coalesce->tx_coalesce_usecs_high ||
-	    coalesce->tx_max_coalesced_frames_high ||
-	    coalesce->rate_sample_interval)
-		return -EINVAL;
-
 	ident = &lif->ionic->ident;
 	if (ident->dev.intr_coal_div == 0) {
 		netdev_warn(netdev, "bad HW value in dev.intr_coal_div = %d\n",
@@ -784,6 +762,7 @@ static int ionic_nway_reset(struct net_device *netdev)
 }
 
 static const struct ethtool_ops ionic_ethtool_ops = {
+	.supported_coalesce_params = ETHTOOL_COALESCE_USECS,
 	.get_drvinfo		= ionic_get_drvinfo,
 	.get_regs_len		= ionic_get_regs_len,
 	.get_regs		= ionic_get_regs,
-- 
2.24.1

[PATCH net-next v3 07/12] hisilicon: let core reject the unsupported coalescing parameters

[Jakub Kicinski]

Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.

This driver correctly rejects all unsupported parameters.
No functional changes.

v3: adjust commit message for new error code and member name

Signed-off-by: Jakub Kicinski <kuba@kernel.org>
---
 drivers/net/ethernet/hisilicon/hip04_eth.c | 16 ++--------------
 1 file changed, 2 insertions(+), 14 deletions(-)

diff --git a/drivers/net/ethernet/hisilicon/hip04_eth.c b/drivers/net/ethernet/hisilicon/hip04_eth.c
index d9718b87279d..12f6c2442a7a 100644
--- a/drivers/net/ethernet/hisilicon/hip04_eth.c
+++ b/drivers/net/ethernet/hisilicon/hip04_eth.c
@@ -811,20 +811,6 @@ static int hip04_set_coalesce(struct net_device *netdev,
 {
 	struct hip04_priv *priv = netdev_priv(netdev);
 
-	/* Check not supported parameters  */
-	if ((ec->rx_max_coalesced_frames) || (ec->rx_coalesce_usecs_irq) ||
-	    (ec->rx_max_coalesced_frames_irq) || (ec->tx_coalesce_usecs_irq) ||
-	    (ec->use_adaptive_rx_coalesce) || (ec->use_adaptive_tx_coalesce) ||
-	    (ec->pkt_rate_low) || (ec->rx_coalesce_usecs_low) ||
-	    (ec->rx_max_coalesced_frames_low) || (ec->tx_coalesce_usecs_high) ||
-	    (ec->tx_max_coalesced_frames_low) || (ec->pkt_rate_high) ||
-	    (ec->tx_coalesce_usecs_low) || (ec->rx_coalesce_usecs_high) ||
-	    (ec->rx_max_coalesced_frames_high) || (ec->rx_coalesce_usecs) ||
-	    (ec->tx_max_coalesced_frames_irq) ||
-	    (ec->stats_block_coalesce_usecs) ||
-	    (ec->tx_max_coalesced_frames_high) || (ec->rate_sample_interval))
-		return -EOPNOTSUPP;
-
 	if ((ec->tx_coalesce_usecs > HIP04_MAX_TX_COALESCE_USECS ||
 	     ec->tx_coalesce_usecs < HIP04_MIN_TX_COALESCE_USECS) ||
 	    (ec->tx_max_coalesced_frames > HIP04_MAX_TX_COALESCE_FRAMES ||
@@ -845,6 +831,8 @@ static void hip04_get_drvinfo(struct net_device *netdev,
 }
 
 static const struct ethtool_ops hip04_ethtool_ops = {
+	.supported_coalesce_params = ETHTOOL_COALESCE_TX_USECS |
+				     ETHTOOL_COALESCE_TX_MAX_FRAMES,
 	.get_coalesce		= hip04_get_coalesce,
 	.set_coalesce		= hip04_set_coalesce,
 	.get_drvinfo		= hip04_get_drvinfo,
-- 
2.24.1

[PATCH net-next v3 08/12] ice: let core reject the unsupported coalescing parameters

[Jakub Kicinski]

Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.

This driver correctly rejects all unsupported parameters.
As a side effect of these changes the info message about
the bad parameter will no longer be printed. We also
always reject the tx_coalesce_usecs_high param, even
if the target queue pair does not have a TX queue.
Error code changes from EINVAL to EOPNOTSUPP.

v2: allow adaptive TX
v3: adjust commit message for new error code and member name

Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
---
 drivers/net/ethernet/intel/ice/ice_ethtool.c | 59 +-------------------
 1 file changed, 3 insertions(+), 56 deletions(-)

diff --git a/drivers/net/ethernet/intel/ice/ice_ethtool.c b/drivers/net/ethernet/intel/ice/ice_ethtool.c
index ab37dddb225b..a016ab1f7f09 100644
--- a/drivers/net/ethernet/intel/ice/ice_ethtool.c
+++ b/drivers/net/ethernet/intel/ice/ice_ethtool.c
@@ -3452,12 +3452,6 @@ ice_set_rc_coalesce(enum ice_container_type c_type, struct ethtool_coalesce *ec,
 
 		break;
 	case ICE_TX_CONTAINER:
-		if (ec->tx_coalesce_usecs_high) {
-			netdev_info(vsi->netdev, "setting %s-usecs-high is not supported\n",
-				    c_type_str);
-			return -EINVAL;
-		}
-
 		use_adaptive_coalesce = ec->use_adaptive_tx_coalesce;
 		coalesce_usecs = ec->tx_coalesce_usecs;
 
@@ -3533,53 +3527,6 @@ ice_set_q_coalesce(struct ice_vsi *vsi, struct ethtool_coalesce *ec, int q_num)
 	return 0;
 }
 
-/**
- * ice_is_coalesce_param_invalid - check for unsupported coalesce parameters
- * @netdev: pointer to the netdev associated with this query
- * @ec: ethtool structure to fill with driver's coalesce settings
- *
- * Print netdev info if driver doesn't support one of the parameters
- * and return error. When any parameters will be implemented, remove only
- * this parameter from param array.
- */
-static int
-ice_is_coalesce_param_invalid(struct net_device *netdev,
-			      struct ethtool_coalesce *ec)
-{
-	struct ice_ethtool_not_used {
-		u32 value;
-		const char *name;
-	} param[] = {
-		{ec->stats_block_coalesce_usecs, "stats-block-usecs"},
-		{ec->rate_sample_interval, "sample-interval"},
-		{ec->pkt_rate_low, "pkt-rate-low"},
-		{ec->pkt_rate_high, "pkt-rate-high"},
-		{ec->rx_max_coalesced_frames, "rx-frames"},
-		{ec->rx_coalesce_usecs_irq, "rx-usecs-irq"},
-		{ec->rx_max_coalesced_frames_irq, "rx-frames-irq"},
-		{ec->tx_max_coalesced_frames, "tx-frames"},
-		{ec->tx_coalesce_usecs_irq, "tx-usecs-irq"},
-		{ec->tx_max_coalesced_frames_irq, "tx-frames-irq"},
-		{ec->rx_coalesce_usecs_low, "rx-usecs-low"},
-		{ec->rx_max_coalesced_frames_low, "rx-frames-low"},
-		{ec->tx_coalesce_usecs_low, "tx-usecs-low"},
-		{ec->tx_max_coalesced_frames_low, "tx-frames-low"},
-		{ec->rx_max_coalesced_frames_high, "rx-frames-high"},
-		{ec->tx_max_coalesced_frames_high, "tx-frames-high"}
-	};
-	int i;
-
-	for (i = 0; i < ARRAY_SIZE(param); i++) {
-		if (param[i].value) {
-			netdev_info(netdev, "Setting %s not supported\n",
-				    param[i].name);
-			return -EINVAL;
-		}
-	}
-
-	return 0;
-}
-
 /**
  * ice_print_if_odd_usecs - print message if user tries to set odd [tx|rx]-usecs
  * @netdev: netdev used for print
@@ -3620,9 +3567,6 @@ __ice_set_coalesce(struct net_device *netdev, struct ethtool_coalesce *ec,
 	struct ice_netdev_priv *np = netdev_priv(netdev);
 	struct ice_vsi *vsi = np->vsi;
 
-	if (ice_is_coalesce_param_invalid(netdev, ec))
-		return -EINVAL;
-
 	if (q_num < 0) {
 		struct ice_q_vector *q_vector = vsi->q_vectors[0];
 		int v_idx;
@@ -3817,6 +3761,9 @@ ice_get_module_eeprom(struct net_device *netdev,
 }
 
 static const struct ethtool_ops ice_ethtool_ops = {
+	.supported_coalesce_params = ETHTOOL_COALESCE_USECS |
+				     ETHTOOL_COALESCE_USE_ADAPTIVE |
+				     ETHTOOL_COALESCE_RX_USECS_HIGH,
 	.get_link_ksettings	= ice_get_link_ksettings,
 	.set_link_ksettings	= ice_set_link_ksettings,
 	.get_drvinfo		= ice_get_drvinfo,
-- 
2.24.1

[PATCH net-next v3 09/12] bnxt: reject unsupported coalescing params

[Jakub Kicinski]

Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.

This driver did not previously reject unsupported parameters.

v3: adjust commit message for new member name

Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
---
 drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c b/drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c
index 7e84f1dc9d87..1fa3a12b5196 100644
--- a/drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c
+++ b/drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c
@@ -3472,6 +3472,12 @@ void bnxt_ethtool_free(struct bnxt *bp)
 }
 
 const struct ethtool_ops bnxt_ethtool_ops = {
+	.supported_coalesce_params = ETHTOOL_COALESCE_USECS |
+				     ETHTOOL_COALESCE_MAX_FRAMES |
+				     ETHTOOL_COALESCE_USECS_IRQ |
+				     ETHTOOL_COALESCE_MAX_FRAMES_IRQ |
+				     ETHTOOL_COALESCE_STATS_BLOCK_USECS |
+				     ETHTOOL_COALESCE_USE_ADAPTIVE_RX,
 	.get_link_ksettings	= bnxt_get_link_ksettings,
 	.set_link_ksettings	= bnxt_set_link_ksettings,
 	.get_pauseparam		= bnxt_get_pauseparam,
-- 
2.24.1

[PATCH net-next v3 10/12] mlx5: reject unsupported coalescing params

[Jakub Kicinski]

Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.

This driver did not previously reject unsupported parameters.

v3: adjust commit message for new member name

Signed-off-by: Jakub Kicinski <kuba@kernel.org>
---
 drivers/net/ethernet/mellanox/mlx5/core/en_ethtool.c    | 3 +++
 drivers/net/ethernet/mellanox/mlx5/core/en_rep.c        | 6 ++++++
 drivers/net/ethernet/mellanox/mlx5/core/ipoib/ethtool.c | 3 +++
 3 files changed, 12 insertions(+)

diff --git a/drivers/net/ethernet/mellanox/mlx5/core/en_ethtool.c b/drivers/net/ethernet/mellanox/mlx5/core/en_ethtool.c
index 06f6f08ff5eb..01539b874b5e 100644
--- a/drivers/net/ethernet/mellanox/mlx5/core/en_ethtool.c
+++ b/drivers/net/ethernet/mellanox/mlx5/core/en_ethtool.c
@@ -1965,6 +1965,9 @@ static int mlx5e_set_rxnfc(struct net_device *dev, struct ethtool_rxnfc *cmd)
 }
 
 const struct ethtool_ops mlx5e_ethtool_ops = {
+	.supported_coalesce_params = ETHTOOL_COALESCE_USECS |
+				     ETHTOOL_COALESCE_MAX_FRAMES |
+				     ETHTOOL_COALESCE_USE_ADAPTIVE,
 	.get_drvinfo       = mlx5e_get_drvinfo,
 	.get_link          = ethtool_op_get_link,
 	.get_strings       = mlx5e_get_strings,
diff --git a/drivers/net/ethernet/mellanox/mlx5/core/en_rep.c b/drivers/net/ethernet/mellanox/mlx5/core/en_rep.c
index 1a8897f80547..c506143c8559 100644
--- a/drivers/net/ethernet/mellanox/mlx5/core/en_rep.c
+++ b/drivers/net/ethernet/mellanox/mlx5/core/en_rep.c
@@ -376,6 +376,9 @@ static int mlx5e_uplink_rep_set_link_ksettings(struct net_device *netdev,
 }
 
 static const struct ethtool_ops mlx5e_rep_ethtool_ops = {
+	.supported_coalesce_params = ETHTOOL_COALESCE_USECS |
+				     ETHTOOL_COALESCE_MAX_FRAMES |
+				     ETHTOOL_COALESCE_USE_ADAPTIVE,
 	.get_drvinfo	   = mlx5e_rep_get_drvinfo,
 	.get_link	   = ethtool_op_get_link,
 	.get_strings       = mlx5e_rep_get_strings,
@@ -392,6 +395,9 @@ static const struct ethtool_ops mlx5e_rep_ethtool_ops = {
 };
 
 static const struct ethtool_ops mlx5e_uplink_rep_ethtool_ops = {
+	.supported_coalesce_params = ETHTOOL_COALESCE_USECS |
+				     ETHTOOL_COALESCE_MAX_FRAMES |
+				     ETHTOOL_COALESCE_USE_ADAPTIVE,
 	.get_drvinfo	   = mlx5e_uplink_rep_get_drvinfo,
 	.get_link	   = ethtool_op_get_link,
 	.get_strings       = mlx5e_rep_get_strings,
diff --git a/drivers/net/ethernet/mellanox/mlx5/core/ipoib/ethtool.c b/drivers/net/ethernet/mellanox/mlx5/core/ipoib/ethtool.c
index 90cb50fe17fd..1eef66ee849e 100644
--- a/drivers/net/ethernet/mellanox/mlx5/core/ipoib/ethtool.c
+++ b/drivers/net/ethernet/mellanox/mlx5/core/ipoib/ethtool.c
@@ -235,6 +235,9 @@ static int mlx5i_get_link_ksettings(struct net_device *netdev,
 }
 
 const struct ethtool_ops mlx5i_ethtool_ops = {
+	.supported_coalesce_params = ETHTOOL_COALESCE_USECS |
+				     ETHTOOL_COALESCE_MAX_FRAMES |
+				     ETHTOOL_COALESCE_USE_ADAPTIVE,
 	.get_drvinfo        = mlx5i_get_drvinfo,
 	.get_strings        = mlx5i_get_strings,
 	.get_sset_count     = mlx5i_get_sset_count,
-- 
2.24.1

[PATCH net-next v3 11/12] e1000e: reject unsupported coalescing params

[Jakub Kicinski]

Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.

This driver did not previously reject unsupported parameters.

v3: adjust commit message for new member name

Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/ethtool.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/net/ethernet/intel/e1000e/ethtool.c b/drivers/net/ethernet/intel/e1000e/ethtool.c
index 9e7881db7859..1d47e2503072 100644
--- a/drivers/net/ethernet/intel/e1000e/ethtool.c
+++ b/drivers/net/ethernet/intel/e1000e/ethtool.c
@@ -2307,6 +2307,7 @@ static int e1000e_get_ts_info(struct net_device *netdev,
 }
 
 static const struct ethtool_ops e1000_ethtool_ops = {
+	.supported_coalesce_params = ETHTOOL_COALESCE_RX_USECS,
 	.get_drvinfo		= e1000_get_drvinfo,
 	.get_regs_len		= e1000_get_regs_len,
 	.get_regs		= e1000_get_regs,
-- 
2.24.1

[PATCH net-next v3 12/12] virtio_net: reject unsupported coalescing params

[Jakub Kicinski]

Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.

This driver correctly rejects all unsupported parameters.
As a side effect of these changes the error code for
unsupported params changes from EINVAL to EOPNOTSUPP.

v2: correctly handle rx-frames (and adjust the commit msg)
v3: adjust commit message for new error code and member name

Signed-off-by: Jakub Kicinski <kuba@kernel.org>
---
 drivers/net/virtio_net.c | 14 +++-----------
 1 file changed, 3 insertions(+), 11 deletions(-)

diff --git a/drivers/net/virtio_net.c b/drivers/net/virtio_net.c
index 84c0d9581f93..11f722460513 100644
--- a/drivers/net/virtio_net.c
+++ b/drivers/net/virtio_net.c
@@ -2202,23 +2202,14 @@ static int virtnet_get_link_ksettings(struct net_device *dev,
 static int virtnet_set_coalesce(struct net_device *dev,
 				struct ethtool_coalesce *ec)
 {
-	struct ethtool_coalesce ec_default = {
-		.cmd = ETHTOOL_SCOALESCE,
-		.rx_max_coalesced_frames = 1,
-	};
 	struct virtnet_info *vi = netdev_priv(dev);
 	int i, napi_weight;
 
-	if (ec->tx_max_coalesced_frames > 1)
+	if (ec->tx_max_coalesced_frames > 1 ||
+	    ec->rx_max_coalesced_frames != 1)
 		return -EINVAL;
 
-	ec_default.tx_max_coalesced_frames = ec->tx_max_coalesced_frames;
 	napi_weight = ec->tx_max_coalesced_frames ? NAPI_POLL_WEIGHT : 0;
-
-	/* disallow changes to fields not explicitly tested above */
-	if (memcmp(ec, &ec_default, sizeof(ec_default)))
-		return -EINVAL;
-
 	if (napi_weight ^ vi->sq[0].napi.weight) {
 		if (dev->flags & IFF_UP)
 			return -EBUSY;
@@ -2273,6 +2264,7 @@ static void virtnet_update_settings(struct virtnet_info *vi)
 }
 
 static const struct ethtool_ops virtnet_ethtool_ops = {
+	.supported_coalesce_params = ETHTOOL_COALESCE_MAX_FRAMES,
 	.get_drvinfo = virtnet_get_drvinfo,
 	.get_link = ethtool_op_get_link,
 	.get_ringparam = virtnet_get_ringparam,
-- 
2.24.1

Re: [PATCH net-next v3 10/12] mlx5: reject unsupported coalescing params

[Saeed Mahameed]

On Wed, 2020-03-04 at 21:15 -0800, Jakub Kicinski wrote:
> Set ethtool_ops->supported_coalesce_params to let
> the core reject unsupported coalescing parameters.
> 
> This driver did not previously reject unsupported parameters.
> 
> v3: adjust commit message for new member name
> 
> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
> ---
>  drivers/net/ethernet/mellanox/mlx5/core/en_ethtool.c    | 3 +++
>  drivers/net/ethernet/mellanox/mlx5/core/en_rep.c        | 6 ++++++
>  drivers/net/ethernet/mellanox/mlx5/core/ipoib/ethtool.c | 3 +++
>  3 files changed, 12 insertions(+)
> 

the only minor thing is the duplication of the same flags in all types
of mlx5 netdevs, all mlx5 netdevs use the same infrastructure of rx/tx
ring management, so they will always share the same flags. 

Anyway i can follow up with a patch to factor out the duplication.

Acked-by: Saeed Mahameed <saeedm@mellanox.com>

> diff --git a/drivers/net/ethernet/mellanox/mlx5/core/en_ethtool.c
> b/drivers/net/ethernet/mellanox/mlx5/core/en_ethtool.c
> index 06f6f08ff5eb..01539b874b5e 100644
> --- a/drivers/net/ethernet/mellanox/mlx5/core/en_ethtool.c
> +++ b/drivers/net/ethernet/mellanox/mlx5/core/en_ethtool.c
> @@ -1965,6 +1965,9 @@ static int mlx5e_set_rxnfc(struct net_device
> *dev, struct ethtool_rxnfc *cmd)
>  }
>  
>  const struct ethtool_ops mlx5e_ethtool_ops = {
> +	.supported_coalesce_params = ETHTOOL_COALESCE_USECS |
> +				     ETHTOOL_COALESCE_MAX_FRAMES |
> +				     ETHTOOL_COALESCE_USE_ADAPTIVE,
>  	.get_drvinfo       = mlx5e_get_drvinfo,
>  	.get_link          = ethtool_op_get_link,
>  	.get_strings       = mlx5e_get_strings,
> diff --git a/drivers/net/ethernet/mellanox/mlx5/core/en_rep.c
> b/drivers/net/ethernet/mellanox/mlx5/core/en_rep.c
> index 1a8897f80547..c506143c8559 100644
> --- a/drivers/net/ethernet/mellanox/mlx5/core/en_rep.c
> +++ b/drivers/net/ethernet/mellanox/mlx5/core/en_rep.c
> @@ -376,6 +376,9 @@ static int
> mlx5e_uplink_rep_set_link_ksettings(struct net_device *netdev,
>  }
>  
>  static const struct ethtool_ops mlx5e_rep_ethtool_ops = {
> +	.supported_coalesce_params = ETHTOOL_COALESCE_USECS |
> +				     ETHTOOL_COALESCE_MAX_FRAMES |
> +				     ETHTOOL_COALESCE_USE_ADAPTIVE,
>  	.get_drvinfo	   = mlx5e_rep_get_drvinfo,
>  	.get_link	   = ethtool_op_get_link,
>  	.get_strings       = mlx5e_rep_get_strings,
> @@ -392,6 +395,9 @@ static const struct ethtool_ops
> mlx5e_rep_ethtool_ops = {
>  };
>  
>  static const struct ethtool_ops mlx5e_uplink_rep_ethtool_ops = {
> +	.supported_coalesce_params = ETHTOOL_COALESCE_USECS |
> +				     ETHTOOL_COALESCE_MAX_FRAMES |
> +				     ETHTOOL_COALESCE_USE_ADAPTIVE,
>  	.get_drvinfo	   = mlx5e_uplink_rep_get_drvinfo,
>  	.get_link	   = ethtool_op_get_link,
>  	.get_strings       = mlx5e_rep_get_strings,
> diff --git a/drivers/net/ethernet/mellanox/mlx5/core/ipoib/ethtool.c
> b/drivers/net/ethernet/mellanox/mlx5/core/ipoib/ethtool.c
> index 90cb50fe17fd..1eef66ee849e 100644
> --- a/drivers/net/ethernet/mellanox/mlx5/core/ipoib/ethtool.c
> +++ b/drivers/net/ethernet/mellanox/mlx5/core/ipoib/ethtool.c
> @@ -235,6 +235,9 @@ static int mlx5i_get_link_ksettings(struct
> net_device *netdev,
>  }
>  
>  const struct ethtool_ops mlx5i_ethtool_ops = {
> +	.supported_coalesce_params = ETHTOOL_COALESCE_USECS |
> +				     ETHTOOL_COALESCE_MAX_FRAMES |
> +				     ETHTOOL_COALESCE_USE_ADAPTIVE,
>  	.get_drvinfo        = mlx5i_get_drvinfo,
>  	.get_strings        = mlx5i_get_strings,
>  	.get_sset_count     = mlx5i_get_sset_count,

Re: [PATCH net-next v3 01/12] ethtool: add infrastructure for centralized checking of coalescing parameters

[Michal Kubecek]

On Wed, Mar 04, 2020 at 09:15:31PM -0800, Jakub Kicinski wrote:
> Linux supports 22 different interrupt coalescing parameters.
> No driver implements them all. Some drivers just ignore the
> ones they don't support, while others have to carry a long
> list of checks to reject unsupported settings.
> 
> To simplify the drivers add the ability to specify inside
> ethtool_ops which parameters are supported and let the core
> reject attempts to set any other one.
> 
> This commit makes the mechanism an opt-in, only drivers which
> set ethtool_opts->coalesce_types to a non-zero value will have
> the checks enforced.
> 
> The same mask is used for global and per queue settings.
> 
> v3: - move the (temporary) check if driver defines types
>       earlier (Michal)
>     - rename used_types -> nonzero_params, and
>       coalesce_types -> supported_coalesce_params (Alex)
>     - use EOPNOTSUPP instead of EINVAL (Andrew, Michal)
> 
> Leaving the long series of ifs for now, it seems nice to
> be able to grep for the field and flag names. This will
> probably have to be revisited once netlink support lands.
> 
> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
> ---

Reviewed-by: Michal Kubecek <mkubecek@suse.cz>

Re: [PATCH net-next v3 01/12] ethtool: add infrastructure for centralized checking of coalescing parameters

[Andrew Lunn]

On Wed, Mar 04, 2020 at 09:15:31PM -0800, Jakub Kicinski wrote:
> Linux supports 22 different interrupt coalescing parameters.
> No driver implements them all. Some drivers just ignore the
> ones they don't support, while others have to carry a long
> list of checks to reject unsupported settings.
> 
> To simplify the drivers add the ability to specify inside
> ethtool_ops which parameters are supported and let the core
> reject attempts to set any other one.
> 
> This commit makes the mechanism an opt-in, only drivers which
> set ethtool_opts->coalesce_types to a non-zero value will have
> the checks enforced.
> 
> The same mask is used for global and per queue settings.
> 
> v3: - move the (temporary) check if driver defines types
>       earlier (Michal)
>     - rename used_types -> nonzero_params, and
>       coalesce_types -> supported_coalesce_params (Alex)
>     - use EOPNOTSUPP instead of EINVAL (Andrew, Michal)
> 
> Leaving the long series of ifs for now, it seems nice to
> be able to grep for the field and flag names. This will
> probably have to be revisited once netlink support lands.
> 
> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>

Reviewed-by: Andrew Lunn <andrew@lunn.ch>

    Andrew

Re: [PATCH net-next v3 02/12] xgbe: let core reject the unsupported coalescing parameters

[Tom Lendacky]

On 3/4/20 11:15 PM, Jakub Kicinski wrote:
> Set ethtool_ops->supported_coalesce_params to let
> the core reject unsupported coalescing parameters.
> 
> This driver correctly rejects all unsupported parameters.
> We are only losing the error print.
> 
> v3: adjust commit message for new error code and member name
> 
> Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Acked-by: Tom Lendacky <thomas.lendacky@amd.com>

> ---
>  drivers/net/ethernet/amd/xgbe/xgbe-ethtool.c | 26 ++------------------
>  1 file changed, 2 insertions(+), 24 deletions(-)
> 
> diff --git a/drivers/net/ethernet/amd/xgbe/xgbe-ethtool.c b/drivers/net/ethernet/amd/xgbe/xgbe-ethtool.c
> index b23c8ee24ee3..61f39a0e04f9 100644
> --- a/drivers/net/ethernet/amd/xgbe/xgbe-ethtool.c
> +++ b/drivers/net/ethernet/amd/xgbe/xgbe-ethtool.c
> @@ -450,30 +450,6 @@ static int xgbe_set_coalesce(struct net_device *netdev,
>  	unsigned int rx_frames, rx_riwt, rx_usecs;
>  	unsigned int tx_frames;
>  
> -	/* Check for not supported parameters  */
> -	if ((ec->rx_coalesce_usecs_irq) ||
> -	    (ec->rx_max_coalesced_frames_irq) ||
> -	    (ec->tx_coalesce_usecs) ||
> -	    (ec->tx_coalesce_usecs_irq) ||
> -	    (ec->tx_max_coalesced_frames_irq) ||
> -	    (ec->stats_block_coalesce_usecs) ||
> -	    (ec->use_adaptive_rx_coalesce) ||
> -	    (ec->use_adaptive_tx_coalesce) ||
> -	    (ec->pkt_rate_low) ||
> -	    (ec->rx_coalesce_usecs_low) ||
> -	    (ec->rx_max_coalesced_frames_low) ||
> -	    (ec->tx_coalesce_usecs_low) ||
> -	    (ec->tx_max_coalesced_frames_low) ||
> -	    (ec->pkt_rate_high) ||
> -	    (ec->rx_coalesce_usecs_high) ||
> -	    (ec->rx_max_coalesced_frames_high) ||
> -	    (ec->tx_coalesce_usecs_high) ||
> -	    (ec->tx_max_coalesced_frames_high) ||
> -	    (ec->rate_sample_interval)) {
> -		netdev_err(netdev, "unsupported coalescing parameter\n");
> -		return -EOPNOTSUPP;
> -	}
> -
>  	rx_riwt = hw_if->usec_to_riwt(pdata, ec->rx_coalesce_usecs);
>  	rx_usecs = ec->rx_coalesce_usecs;
>  	rx_frames = ec->rx_max_coalesced_frames;
> @@ -837,6 +813,8 @@ static int xgbe_set_channels(struct net_device *netdev,
>  }
>  
>  static const struct ethtool_ops xgbe_ethtool_ops = {
> +	.supported_coalesce_params = ETHTOOL_COALESCE_RX_USECS |
> +				     ETHTOOL_COALESCE_MAX_FRAMES,
>  	.get_drvinfo = xgbe_get_drvinfo,
>  	.get_msglevel = xgbe_get_msglevel,
>  	.set_msglevel = xgbe_set_msglevel,
> 

Re: [PATCH net-next v3 01/12] ethtool: add infrastructure for centralized checking of coalescing parameters

[Alexander Duyck]

On Wed, 2020-03-04 at 21:15 -0800, Jakub Kicinski wrote:
> Linux supports 22 different interrupt coalescing parameters.
> No driver implements them all. Some drivers just ignore the
> ones they don't support, while others have to carry a long
> list of checks to reject unsupported settings.
> 
> To simplify the drivers add the ability to specify inside
> ethtool_ops which parameters are supported and let the core
> reject attempts to set any other one.
> 
> This commit makes the mechanism an opt-in, only drivers which
> set ethtool_opts->coalesce_types to a non-zero value will have
> the checks enforced.
> 
> The same mask is used for global and per queue settings.
> 
> v3: - move the (temporary) check if driver defines types
>       earlier (Michal)
>     - rename used_types -> nonzero_params, and
>       coalesce_types -> supported_coalesce_params (Alex)
>     - use EOPNOTSUPP instead of EINVAL (Andrew, Michal)
> 
> Leaving the long series of ifs for now, it seems nice to
> be able to grep for the field and flag names. This will
> probably have to be revisited once netlink support lands.
> 
> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
> ---

Reviewed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>

Re: [PATCH net-next v3 00/12] ethtool: consolidate parameter checking for irq coalescing

[David Miller]

From: Jakub Kicinski <kuba@kernel.org>
Date: Wed,  4 Mar 2020 21:15:30 -0800

> This set aims to simplify and unify the unsupported irq
> coalescing parameter handling.

Series applied, thanks Jakub.