From: Ansuel Smith <ansuelsmth@gmail.com>
To: Andrew Lunn <andrew@lunn.ch>,
Vivien Didelot <vivien.didelot@gmail.com>,
Florian Fainelli <f.fainelli@gmail.com>,
Vladimir Oltean <olteanv@gmail.com>,
"David S. Miller" <davem@davemloft.net>,
Jakub Kicinski <kuba@kernel.org>,
Rob Herring <robh+dt@kernel.org>,
Heiner Kallweit <hkallweit1@gmail.com>,
Russell King <linux@armlinux.org.uk>,
Ansuel Smith <ansuelsmth@gmail.com>,
netdev@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org
Cc: Matthew Hagan <mnhagan88@gmail.com>
Subject: [net-next PATCH v2 08/15] dt-bindings: net: dsa: qca8k: Add MAC swap and clock phase properties
Date: Fri, 8 Oct 2021 02:22:18 +0200 [thread overview]
Message-ID: <20211008002225.2426-9-ansuelsmth@gmail.com> (raw)
In-Reply-To: <20211008002225.2426-1-ansuelsmth@gmail.com>
Add names and decriptions of additional PORT0_PAD_CTRL properties.
Document new binding qca,mac6_exchange that exchange the mac0 port
with mac6.
qca,sgmii-(rx|tx)clk-falling-edge are for setting the respective clock
phase to failling edge.
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
---
Documentation/devicetree/bindings/net/dsa/qca8k.txt | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/Documentation/devicetree/bindings/net/dsa/qca8k.txt b/Documentation/devicetree/bindings/net/dsa/qca8k.txt
index 9383d6bf2426..208ee5bc1bbb 100644
--- a/Documentation/devicetree/bindings/net/dsa/qca8k.txt
+++ b/Documentation/devicetree/bindings/net/dsa/qca8k.txt
@@ -13,6 +13,11 @@ Required properties:
Optional properties:
- reset-gpios: GPIO to be used to reset the whole device
+- qca,mac6-exchange: Internally swap MAC0 with MAC6.
+- qca,sgmii-rxclk-falling-edge: Set the receive clock phase to falling edge.
+ Mostly used in qca8327 with CPU port 0 set to
+ sgmii.
+- qca,sgmii-txclk-falling-edge: Set the transmit clock phase to falling edge.
- qca,rgmii0-1-8v: Set the internal regulator to supply 1.8v for MAC0 port.
This is needed for qca8337 and toggles the supply voltage
from 1.5v to 1.8v. For the specific regs it was observed
--
2.32.0
next prev parent reply other threads:[~2021-10-08 0:23 UTC|newest]
Thread overview: 35+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-10-08 0:22 [net-next PATCH v2 00/15] Multiple improvement for qca8337 switch Ansuel Smith
2021-10-08 0:22 ` [net PATCH v2 01/15] drivers: net: phy: at803x: fix resume for QCA8327 phy Ansuel Smith
2021-10-08 2:23 ` Jakub Kicinski
2021-10-08 8:45 ` Ansuel Smith
2021-10-08 14:21 ` Jakub Kicinski
2021-10-08 0:22 ` [net PATCH v2 02/15] drivers: net: phy: at803x: add DAC amplitude fix for 8327 phy Ansuel Smith
2021-10-08 0:22 ` [net-next PATCH v2 03/15] drivers: net: phy: at803x: enable prefer master for 83xx internal phy Ansuel Smith
2021-10-08 0:22 ` [net-next PATCH v2 04/15] drivers: net: phy: at803x: better describe debug regs Ansuel Smith
2021-10-09 15:08 ` Andrew Lunn
2021-10-08 0:22 ` [net-next PATCH v2 05/15] net: dsa: qca8k: add mac_power_sel support Ansuel Smith
2021-10-08 0:22 ` [net-next PATCH v2 06/15] dt-bindings: net: dsa: qca8k: document rgmii_1_8v bindings Ansuel Smith
2021-10-09 15:18 ` Andrew Lunn
2021-10-09 15:30 ` Ansuel Smith
2021-10-09 17:29 ` Andrew Lunn
2021-10-08 0:22 ` [net-next PATCH v2 07/15] net: dsa: qca8k: add support for mac6_exchange, sgmii falling edge Ansuel Smith
2021-10-08 0:22 ` Ansuel Smith [this message]
2021-10-09 17:07 ` [net-next PATCH v2 08/15] dt-bindings: net: dsa: qca8k: Add MAC swap and clock phase properties Andrew Lunn
2021-10-09 18:08 ` Ansuel Smith
2021-10-09 19:47 ` Andrew Lunn
2021-10-09 20:06 ` Ansuel Smith
2021-10-09 21:37 ` Andrew Lunn
2021-10-09 22:23 ` Ansuel Smith
2021-10-08 0:22 ` [net-next PATCH v2 09/15] net: dsa: qca8k: move rgmii delay detection to phylink mac_config Ansuel Smith
2021-10-08 0:22 ` [net-next PATCH v2 10/15] net: dsa: qca8k: add explicit SGMII PLL enable Ansuel Smith
2021-10-08 0:22 ` [net-next PATCH v2 11/15] dt-bindings: net: dsa: qca8k: Document qca,sgmii-enable-pll Ansuel Smith
2021-10-09 17:13 ` Andrew Lunn
2021-10-09 18:14 ` Ansuel Smith
2021-10-08 0:22 ` [net-next PATCH v2 12/15] drivers: net: dsa: qca8k: add support for pws config reg Ansuel Smith
2021-10-08 0:22 ` [net-next PATCH v2 13/15] dt-bindings: net: dsa: qca8k: document open drain binding Ansuel Smith
2021-10-09 17:20 ` Andrew Lunn
2021-10-09 23:16 ` Ansuel Smith
2021-10-08 0:22 ` [net-next PATCH v2 14/15] drivers: net: dsa: qca8k: add support for QCA8328 Ansuel Smith
2021-10-08 0:22 ` [net-next PATCH v2 15/15] dt-bindings: net: dsa: qca8k: document support for qca8328 Ansuel Smith
2021-10-09 17:24 ` Andrew Lunn
2021-10-09 18:17 ` Ansuel Smith
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20211008002225.2426-9-ansuelsmth@gmail.com \
--to=ansuelsmth@gmail.com \
--cc=andrew@lunn.ch \
--cc=davem@davemloft.net \
--cc=devicetree@vger.kernel.org \
--cc=f.fainelli@gmail.com \
--cc=hkallweit1@gmail.com \
--cc=kuba@kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux@armlinux.org.uk \
--cc=mnhagan88@gmail.com \
--cc=netdev@vger.kernel.org \
--cc=olteanv@gmail.com \
--cc=robh+dt@kernel.org \
--cc=vivien.didelot@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).