* [PATCH 0/1] Fix Aspeed ast2600 MAC TX hang
@ 2020-10-14 6:06 Dylan Hung
2020-10-14 6:06 ` [PATCH 1/1] net: ftgmac100: Fix Aspeed ast2600 TX hang issue Dylan Hung
0 siblings, 1 reply; 8+ messages in thread
From: Dylan Hung @ 2020-10-14 6:06 UTC (permalink / raw)
To: davem, kuba, netdev, linux-kernel, ratbert, linux-aspeed, openbmc; +Cc: BMC-SW
This patch fixes the TX hang issue on Aspeed AST2600.
Two HW arbitration features are added onto ast2600, but these features will
cause MAC TX to hang when handling scatter-gather DMA. These two
problematic features can be disabled by setting MAC register 0x58 bit28
and bit27.
Dylan Hung (1):
net: ftgmac100: Fix Aspeed ast2600 TX hang issue
drivers/net/ethernet/faraday/ftgmac100.c | 5 +++++
drivers/net/ethernet/faraday/ftgmac100.h | 8 ++++++++
2 files changed, 13 insertions(+)
--
2.17.1
^ permalink raw reply [flat|nested] 8+ messages in thread
* [PATCH 1/1] net: ftgmac100: Fix Aspeed ast2600 TX hang issue
2020-10-14 6:06 [PATCH 0/1] Fix Aspeed ast2600 MAC TX hang Dylan Hung
@ 2020-10-14 6:06 ` Dylan Hung
2020-10-14 6:41 ` Joel Stanley
2020-10-16 22:37 ` Jakub Kicinski
0 siblings, 2 replies; 8+ messages in thread
From: Dylan Hung @ 2020-10-14 6:06 UTC (permalink / raw)
To: davem, kuba, netdev, linux-kernel, ratbert, linux-aspeed, openbmc; +Cc: BMC-SW
The new HW arbitration feature on Aspeed ast2600 will cause MAC TX to
hang when handling scatter-gather DMA. Disable the problematic feature
by setting MAC register 0x58 bit28 and bit27.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
---
drivers/net/ethernet/faraday/ftgmac100.c | 5 +++++
drivers/net/ethernet/faraday/ftgmac100.h | 8 ++++++++
2 files changed, 13 insertions(+)
diff --git a/drivers/net/ethernet/faraday/ftgmac100.c b/drivers/net/ethernet/faraday/ftgmac100.c
index 87236206366f..00024dd41147 100644
--- a/drivers/net/ethernet/faraday/ftgmac100.c
+++ b/drivers/net/ethernet/faraday/ftgmac100.c
@@ -1817,6 +1817,11 @@ static int ftgmac100_probe(struct platform_device *pdev)
priv->rxdes0_edorr_mask = BIT(30);
priv->txdes0_edotr_mask = BIT(30);
priv->is_aspeed = true;
+ /* Disable ast2600 problematic HW arbitration */
+ if (of_device_is_compatible(np, "aspeed,ast2600-mac")) {
+ iowrite32(FTGMAC100_TM_DEFAULT,
+ priv->base + FTGMAC100_OFFSET_TM);
+ }
} else {
priv->rxdes0_edorr_mask = BIT(15);
priv->txdes0_edotr_mask = BIT(15);
diff --git a/drivers/net/ethernet/faraday/ftgmac100.h b/drivers/net/ethernet/faraday/ftgmac100.h
index e5876a3fda91..63b3e02fab16 100644
--- a/drivers/net/ethernet/faraday/ftgmac100.h
+++ b/drivers/net/ethernet/faraday/ftgmac100.h
@@ -169,6 +169,14 @@
#define FTGMAC100_MACCR_FAST_MODE (1 << 19)
#define FTGMAC100_MACCR_SW_RST (1 << 31)
+/*
+ * test mode control register
+ */
+#define FTGMAC100_TM_RQ_TX_VALID_DIS (1 << 28)
+#define FTGMAC100_TM_RQ_RR_IDLE_PREV (1 << 27)
+#define FTGMAC100_TM_DEFAULT \
+ (FTGMAC100_TM_RQ_TX_VALID_DIS | FTGMAC100_TM_RQ_RR_IDLE_PREV)
+
/*
* PHY control register
*/
--
2.17.1
^ permalink raw reply related [flat|nested] 8+ messages in thread
* Re: [PATCH 1/1] net: ftgmac100: Fix Aspeed ast2600 TX hang issue
2020-10-14 6:06 ` [PATCH 1/1] net: ftgmac100: Fix Aspeed ast2600 TX hang issue Dylan Hung
@ 2020-10-14 6:41 ` Joel Stanley
2020-10-14 7:58 ` Dylan Hung
2020-10-16 22:37 ` Jakub Kicinski
1 sibling, 1 reply; 8+ messages in thread
From: Joel Stanley @ 2020-10-14 6:41 UTC (permalink / raw)
To: Dylan Hung
Cc: BMC-SW, Po-Yu Chuang, linux-aspeed, netdev, OpenBMC Maillist,
Linux Kernel Mailing List, Jakub Kicinski, David S . Miller
On Wed, 14 Oct 2020 at 06:07, Dylan Hung <dylan_hung@aspeedtech.com> wrote:
>
> The new HW arbitration feature on Aspeed ast2600 will cause MAC TX to
> hang when handling scatter-gather DMA. Disable the problematic feature
> by setting MAC register 0x58 bit28 and bit27.
Hi Dylan,
What are the symptoms of this issue? We are seeing this on our systems:
[29376.090637] WARNING: CPU: 0 PID: 9 at net/sched/sch_generic.c:442
dev_watchdog+0x2f0/0x2f4
[29376.099898] NETDEV WATCHDOG: eth0 (ftgmac100): transmit queue 0 timed out
> Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
This fixes support for the ast2600, so we can put:
Fixes: 39bfab8844a0 ("net: ftgmac100: Add support for DT phy-handle property")
Reviewed-by: Joel Stanley <joel@jms.id.au>
> ---
> drivers/net/ethernet/faraday/ftgmac100.c | 5 +++++
> drivers/net/ethernet/faraday/ftgmac100.h | 8 ++++++++
> 2 files changed, 13 insertions(+)
>
> diff --git a/drivers/net/ethernet/faraday/ftgmac100.c b/drivers/net/ethernet/faraday/ftgmac100.c
> index 87236206366f..00024dd41147 100644
> --- a/drivers/net/ethernet/faraday/ftgmac100.c
> +++ b/drivers/net/ethernet/faraday/ftgmac100.c
> @@ -1817,6 +1817,11 @@ static int ftgmac100_probe(struct platform_device *pdev)
> priv->rxdes0_edorr_mask = BIT(30);
> priv->txdes0_edotr_mask = BIT(30);
> priv->is_aspeed = true;
> + /* Disable ast2600 problematic HW arbitration */
> + if (of_device_is_compatible(np, "aspeed,ast2600-mac")) {
> + iowrite32(FTGMAC100_TM_DEFAULT,
> + priv->base + FTGMAC100_OFFSET_TM);
> + }
> } else {
> priv->rxdes0_edorr_mask = BIT(15);
> priv->txdes0_edotr_mask = BIT(15);
> diff --git a/drivers/net/ethernet/faraday/ftgmac100.h b/drivers/net/ethernet/faraday/ftgmac100.h
> index e5876a3fda91..63b3e02fab16 100644
> --- a/drivers/net/ethernet/faraday/ftgmac100.h
> +++ b/drivers/net/ethernet/faraday/ftgmac100.h
> @@ -169,6 +169,14 @@
> #define FTGMAC100_MACCR_FAST_MODE (1 << 19)
> #define FTGMAC100_MACCR_SW_RST (1 << 31)
>
> +/*
> + * test mode control register
> + */
> +#define FTGMAC100_TM_RQ_TX_VALID_DIS (1 << 28)
> +#define FTGMAC100_TM_RQ_RR_IDLE_PREV (1 << 27)
> +#define FTGMAC100_TM_DEFAULT \
> + (FTGMAC100_TM_RQ_TX_VALID_DIS | FTGMAC100_TM_RQ_RR_IDLE_PREV)
Will aspeed issue an updated datasheet with this register documented?
> +
> /*
> * PHY control register
> */
> --
> 2.17.1
>
^ permalink raw reply [flat|nested] 8+ messages in thread
* RE: [PATCH 1/1] net: ftgmac100: Fix Aspeed ast2600 TX hang issue
2020-10-14 6:41 ` Joel Stanley
@ 2020-10-14 7:58 ` Dylan Hung
2020-10-14 22:31 ` Joel Stanley
0 siblings, 1 reply; 8+ messages in thread
From: Dylan Hung @ 2020-10-14 7:58 UTC (permalink / raw)
To: Joel Stanley
Cc: BMC-SW, Po-Yu Chuang, linux-aspeed, netdev, OpenBMC Maillist,
Linux Kernel Mailing List, Jakub Kicinski, David S . Miller
Hi Joel,
> -----Original Message-----
> From: Joel Stanley [mailto:joel@jms.id.au]
> Sent: Wednesday, October 14, 2020 2:41 PM
> To: Dylan Hung <dylan_hung@aspeedtech.com>
> Cc: David S . Miller <davem@davemloft.net>; Jakub Kicinski
> <kuba@kernel.org>; netdev@vger.kernel.org; Linux Kernel Mailing List
> <linux-kernel@vger.kernel.org>; Po-Yu Chuang <ratbert@faraday-tech.com>;
> linux-aspeed <linux-aspeed@lists.ozlabs.org>; OpenBMC Maillist
> <openbmc@lists.ozlabs.org>; BMC-SW <BMC-SW@aspeedtech.com>
> Subject: Re: [PATCH 1/1] net: ftgmac100: Fix Aspeed ast2600 TX hang issue
>
> On Wed, 14 Oct 2020 at 06:07, Dylan Hung <dylan_hung@aspeedtech.com>
> wrote:
> >
> > The new HW arbitration feature on Aspeed ast2600 will cause MAC TX to
> > hang when handling scatter-gather DMA. Disable the problematic
> > feature by setting MAC register 0x58 bit28 and bit27.
>
> Hi Dylan,
>
> What are the symptoms of this issue? We are seeing this on our systems:
>
> [29376.090637] WARNING: CPU: 0 PID: 9 at net/sched/sch_generic.c:442
> dev_watchdog+0x2f0/0x2f4
> [29376.099898] NETDEV WATCHDOG: eth0 (ftgmac100): transmit queue 0
> timed out
>
May I know your soc version? This issue happens on ast2600 version A1. The registers to fix this issue are meaningless/reserved on A0 chip, so it is okay to set them on either A0 or A1.
I was encountering this issue when I was running the iperf TX test. The symptom is the TX descriptors are consumed, but no complete packet is sent out.
> > Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
>
> This fixes support for the ast2600, so we can put:
>
> Fixes: 39bfab8844a0 ("net: ftgmac100: Add support for DT phy-handle
> property")
>
> Reviewed-by: Joel Stanley <joel@jms.id.au>
>
> > ---
> > drivers/net/ethernet/faraday/ftgmac100.c | 5 +++++
> > drivers/net/ethernet/faraday/ftgmac100.h | 8 ++++++++
> > 2 files changed, 13 insertions(+)
> >
> > diff --git a/drivers/net/ethernet/faraday/ftgmac100.c
> > b/drivers/net/ethernet/faraday/ftgmac100.c
> > index 87236206366f..00024dd41147 100644
> > --- a/drivers/net/ethernet/faraday/ftgmac100.c
> > +++ b/drivers/net/ethernet/faraday/ftgmac100.c
> > @@ -1817,6 +1817,11 @@ static int ftgmac100_probe(struct
> platform_device *pdev)
> > priv->rxdes0_edorr_mask = BIT(30);
> > priv->txdes0_edotr_mask = BIT(30);
> > priv->is_aspeed = true;
> > + /* Disable ast2600 problematic HW arbitration */
> > + if (of_device_is_compatible(np, "aspeed,ast2600-mac"))
> {
> > + iowrite32(FTGMAC100_TM_DEFAULT,
> > + priv->base +
> FTGMAC100_OFFSET_TM);
> > + }
> > } else {
> > priv->rxdes0_edorr_mask = BIT(15);
> > priv->txdes0_edotr_mask = BIT(15); diff --git
> > a/drivers/net/ethernet/faraday/ftgmac100.h
> > b/drivers/net/ethernet/faraday/ftgmac100.h
> > index e5876a3fda91..63b3e02fab16 100644
> > --- a/drivers/net/ethernet/faraday/ftgmac100.h
> > +++ b/drivers/net/ethernet/faraday/ftgmac100.h
> > @@ -169,6 +169,14 @@
> > #define FTGMAC100_MACCR_FAST_MODE (1 << 19)
> > #define FTGMAC100_MACCR_SW_RST (1 << 31)
> >
> > +/*
> > + * test mode control register
> > + */
> > +#define FTGMAC100_TM_RQ_TX_VALID_DIS (1 << 28) #define
> > +FTGMAC100_TM_RQ_RR_IDLE_PREV (1 << 27)
> > +#define FTGMAC100_TM_DEFAULT
> \
> > + (FTGMAC100_TM_RQ_TX_VALID_DIS |
> FTGMAC100_TM_RQ_RR_IDLE_PREV)
>
> Will aspeed issue an updated datasheet with this register documented?
>
>
> > +
> > /*
> > * PHY control register
> > */
> > --
> > 2.17.1
> >
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH 1/1] net: ftgmac100: Fix Aspeed ast2600 TX hang issue
2020-10-14 7:58 ` Dylan Hung
@ 2020-10-14 22:31 ` Joel Stanley
2020-10-15 1:49 ` Dylan Hung
0 siblings, 1 reply; 8+ messages in thread
From: Joel Stanley @ 2020-10-14 22:31 UTC (permalink / raw)
To: Dylan Hung
Cc: BMC-SW, Po-Yu Chuang, linux-aspeed, netdev, OpenBMC Maillist,
Linux Kernel Mailing List, Jakub Kicinski, David S . Miller
On Wed, 14 Oct 2020 at 13:32, Dylan Hung <dylan_hung@aspeedtech.com> wrote:
> > > The new HW arbitration feature on Aspeed ast2600 will cause MAC TX to
> > > hang when handling scatter-gather DMA. Disable the problematic
> > > feature by setting MAC register 0x58 bit28 and bit27.
> >
> > Hi Dylan,
> >
> > What are the symptoms of this issue? We are seeing this on our systems:
> >
> > [29376.090637] WARNING: CPU: 0 PID: 9 at net/sched/sch_generic.c:442
> > dev_watchdog+0x2f0/0x2f4
> > [29376.099898] NETDEV WATCHDOG: eth0 (ftgmac100): transmit queue 0
> > timed out
> >
>
> May I know your soc version? This issue happens on ast2600 version A1. The registers to fix this issue are meaningless/reserved on A0 chip, so it is okay to set them on either A0 or A1.
We are running the A1. All of our A0 parts have been replaced with A1.
> I was encountering this issue when I was running the iperf TX test. The symptom is the TX descriptors are consumed, but no complete packet is sent out.
What parameters are you using for iperf? I did a lot of testing with
iperf3 (and stress-ng running at the same time) and couldn't reproduce
the error.
We could only reproduce it when performing other functions, such as
debugging/booting the host processor.
> > > +/*
> > > + * test mode control register
> > > + */
> > > +#define FTGMAC100_TM_RQ_TX_VALID_DIS (1 << 28) #define
> > > +FTGMAC100_TM_RQ_RR_IDLE_PREV (1 << 27)
> > > +#define FTGMAC100_TM_DEFAULT
> > \
> > > + (FTGMAC100_TM_RQ_TX_VALID_DIS |
> > FTGMAC100_TM_RQ_RR_IDLE_PREV)
> >
> > Will aspeed issue an updated datasheet with this register documented?
Did you see this question?
Cheers,
Joel
^ permalink raw reply [flat|nested] 8+ messages in thread
* RE: [PATCH 1/1] net: ftgmac100: Fix Aspeed ast2600 TX hang issue
2020-10-14 22:31 ` Joel Stanley
@ 2020-10-15 1:49 ` Dylan Hung
2020-10-15 2:32 ` Joel Stanley
0 siblings, 1 reply; 8+ messages in thread
From: Dylan Hung @ 2020-10-15 1:49 UTC (permalink / raw)
To: Joel Stanley
Cc: BMC-SW, Po-Yu Chuang, linux-aspeed, netdev, OpenBMC Maillist,
Linux Kernel Mailing List, Jakub Kicinski, David S . Miller
> -----Original Message-----
> From: Joel Stanley [mailto:joel@jms.id.au]
> Sent: Thursday, October 15, 2020 6:31 AM
> To: Dylan Hung <dylan_hung@aspeedtech.com>
> Cc: David S . Miller <davem@davemloft.net>; Jakub Kicinski
> <kuba@kernel.org>; netdev@vger.kernel.org; Linux Kernel Mailing List
> <linux-kernel@vger.kernel.org>; Po-Yu Chuang <ratbert@faraday-tech.com>;
> linux-aspeed <linux-aspeed@lists.ozlabs.org>; OpenBMC Maillist
> <openbmc@lists.ozlabs.org>; BMC-SW <BMC-SW@aspeedtech.com>
> Subject: Re: [PATCH 1/1] net: ftgmac100: Fix Aspeed ast2600 TX hang issue
>
> On Wed, 14 Oct 2020 at 13:32, Dylan Hung <dylan_hung@aspeedtech.com>
> wrote:
> > > > The new HW arbitration feature on Aspeed ast2600 will cause MAC TX
> > > > to hang when handling scatter-gather DMA. Disable the problematic
> > > > feature by setting MAC register 0x58 bit28 and bit27.
> > >
> > > Hi Dylan,
> > >
> > > What are the symptoms of this issue? We are seeing this on our systems:
> > >
> > > [29376.090637] WARNING: CPU: 0 PID: 9 at net/sched/sch_generic.c:442
> > > dev_watchdog+0x2f0/0x2f4
> > > [29376.099898] NETDEV WATCHDOG: eth0 (ftgmac100): transmit queue 0
> > > timed out
> > >
> >
> > May I know your soc version? This issue happens on ast2600 version A1.
> The registers to fix this issue are meaningless/reserved on A0 chip, so it is
> okay to set them on either A0 or A1.
>
> We are running the A1. All of our A0 parts have been replaced with A1.
>
> > I was encountering this issue when I was running the iperf TX test. The
> symptom is the TX descriptors are consumed, but no complete packet is sent
> out.
>
> What parameters are you using for iperf? I did a lot of testing with
> iperf3 (and stress-ng running at the same time) and couldn't reproduce the
> error.
>
I simply use "iperf -c <server ip>" on ast2600. It is very easy to reproduce. I append the log below:
Noticed that this issue only happens when HW scatter-gather (NETIF_F_SG) is on.
[AST /]$ iperf3 -c 192.168.100.89
Connecting to host 192.168.100.89, port 5201
[ 4] local 192.168.100.45 port 45346 connected to 192.168.100.89 port 5201
[ ID] Interval Transfer Bandwidth Retr Cwnd
[ 4] 0.00-1.00 sec 44.8 MBytes 375 Mbits/sec 2 1.43 KBytes
[ 4] 1.00-2.00 sec 0.00 Bytes 0.00 bits/sec 2 1.43 KBytes
[ 4] 2.00-3.00 sec 0.00 Bytes 0.00 bits/sec 0 1.43 KBytes
[ 4] 3.00-4.00 sec 0.00 Bytes 0.00 bits/sec 1 1.43 KBytes
[ 4] 4.00-5.00 sec 0.00 Bytes 0.00 bits/sec 0 1.43 KBytes
^C[ 4] 5.00-5.88 sec 0.00 Bytes 0.00 bits/sec 0 1.43 KBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bandwidth Retr
[ 4] 0.00-5.88 sec 44.8 MBytes 64.0 Mbits/sec 5 sender
[ 4] 0.00-5.88 sec 0.00 Bytes 0.00 bits/sec receiver
iperf3: interrupt - the client has terminated
> We could only reproduce it when performing other functions, such as
> debugging/booting the host processor.
>
Could it be another issue?
> > > > +/*
> > > > + * test mode control register
> > > > + */
> > > > +#define FTGMAC100_TM_RQ_TX_VALID_DIS (1 << 28) #define
> > > > +FTGMAC100_TM_RQ_RR_IDLE_PREV (1 << 27) #define
> > > > +FTGMAC100_TM_DEFAULT
> > > \
> > > > + (FTGMAC100_TM_RQ_TX_VALID_DIS |
> > > FTGMAC100_TM_RQ_RR_IDLE_PREV)
> > >
> > > Will aspeed issue an updated datasheet with this register documented?
>
> Did you see this question?
>
Sorry, I missed this question. Aspeed will update the datasheet accordingly.
> Cheers,
>
> Joel
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH 1/1] net: ftgmac100: Fix Aspeed ast2600 TX hang issue
2020-10-15 1:49 ` Dylan Hung
@ 2020-10-15 2:32 ` Joel Stanley
0 siblings, 0 replies; 8+ messages in thread
From: Joel Stanley @ 2020-10-15 2:32 UTC (permalink / raw)
To: Dylan Hung
Cc: BMC-SW, Po-Yu Chuang, linux-aspeed, netdev, OpenBMC Maillist,
Linux Kernel Mailing List, Jakub Kicinski, David S . Miller
On Thu, 15 Oct 2020 at 01:49, Dylan Hung <dylan_hung@aspeedtech.com> wrote:
> > > I was encountering this issue when I was running the iperf TX test. The
> > symptom is the TX descriptors are consumed, but no complete packet is sent
> > out.
> >
> > What parameters are you using for iperf? I did a lot of testing with
> > iperf3 (and stress-ng running at the same time) and couldn't reproduce the
> > error.
> >
>
> I simply use "iperf -c <server ip>" on ast2600. It is very easy to reproduce. I append the log below:
> Noticed that this issue only happens when HW scatter-gather (NETIF_F_SG) is on.
Ok. This appears to be on by default in the
drivers/net/ethernet/faraday/ftgmac100.c:
netdev->hw_features = NETIF_F_RXCSUM | NETIF_F_HW_CSUM |
NETIF_F_GRO | NETIF_F_SG | NETIF_F_HW_VLAN_CTAG_RX |
NETIF_F_HW_VLAN_CTAG_TX;
> [AST /]$ iperf3 -c 192.168.100.89
> Connecting to host 192.168.100.89, port 5201
> [ 4] local 192.168.100.45 port 45346 connected to 192.168.100.89 port 5201
> [ ID] Interval Transfer Bandwidth Retr Cwnd
> [ 4] 0.00-1.00 sec 44.8 MBytes 375 Mbits/sec 2 1.43 KBytes
> [ 4] 1.00-2.00 sec 0.00 Bytes 0.00 bits/sec 2 1.43 KBytes
> [ 4] 2.00-3.00 sec 0.00 Bytes 0.00 bits/sec 0 1.43 KBytes
> [ 4] 3.00-4.00 sec 0.00 Bytes 0.00 bits/sec 1 1.43 KBytes
> [ 4] 4.00-5.00 sec 0.00 Bytes 0.00 bits/sec 0 1.43 KBytes
> ^C[ 4] 5.00-5.88 sec 0.00 Bytes 0.00 bits/sec 0 1.43 KBytes
> - - - - - - - - - - - - - - - - - - - - - - - - -
> [ ID] Interval Transfer Bandwidth Retr
> [ 4] 0.00-5.88 sec 44.8 MBytes 64.0 Mbits/sec 5 sender
> [ 4] 0.00-5.88 sec 0.00 Bytes 0.00 bits/sec receiver
> iperf3: interrupt - the client has terminated
I just realised my test machine must be on a 100Mbit network. I will
try testing on a gigabit network.
> > We could only reproduce it when performing other functions, such as
> > debugging/booting the host processor.
> >
> Could it be another issue?
I hope not! We have deployed your patch on our systems and I will let
you know if we see the bug again.
> > > > > +/*
> > > > > + * test mode control register
> > > > > + */
> > > > > +#define FTGMAC100_TM_RQ_TX_VALID_DIS (1 << 28) #define
> > > > > +FTGMAC100_TM_RQ_RR_IDLE_PREV (1 << 27) #define
> > > > > +FTGMAC100_TM_DEFAULT
> > > > \
> > > > > + (FTGMAC100_TM_RQ_TX_VALID_DIS |
> > > > FTGMAC100_TM_RQ_RR_IDLE_PREV)
> > > >
> > > > Will aspeed issue an updated datasheet with this register documented?
> >
> > Did you see this question?
> >
> Sorry, I missed this question. Aspeed will update the datasheet accordingly.
Thank you.
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH 1/1] net: ftgmac100: Fix Aspeed ast2600 TX hang issue
2020-10-14 6:06 ` [PATCH 1/1] net: ftgmac100: Fix Aspeed ast2600 TX hang issue Dylan Hung
2020-10-14 6:41 ` Joel Stanley
@ 2020-10-16 22:37 ` Jakub Kicinski
1 sibling, 0 replies; 8+ messages in thread
From: Jakub Kicinski @ 2020-10-16 22:37 UTC (permalink / raw)
To: Dylan Hung
Cc: BMC-SW, ratbert, linux-aspeed, netdev, openbmc, linux-kernel, davem
On Wed, 14 Oct 2020 14:06:32 +0800 Dylan Hung wrote:
> The new HW arbitration feature on Aspeed ast2600 will cause MAC TX to
> hang when handling scatter-gather DMA. Disable the problematic feature
> by setting MAC register 0x58 bit28 and bit27.
>
> Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Applied, thank you.
^ permalink raw reply [flat|nested] 8+ messages in thread
end of thread, other threads:[~2020-10-19 3:08 UTC | newest]
Thread overview: 8+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-10-14 6:06 [PATCH 0/1] Fix Aspeed ast2600 MAC TX hang Dylan Hung
2020-10-14 6:06 ` [PATCH 1/1] net: ftgmac100: Fix Aspeed ast2600 TX hang issue Dylan Hung
2020-10-14 6:41 ` Joel Stanley
2020-10-14 7:58 ` Dylan Hung
2020-10-14 22:31 ` Joel Stanley
2020-10-15 1:49 ` Dylan Hung
2020-10-15 2:32 ` Joel Stanley
2020-10-16 22:37 ` Jakub Kicinski
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).