linux-kernel.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Richard Leitner <richard.leitner@skidata.com>
To: <dmitry.torokhov@gmail.com>, <robh+dt@kernel.org>,
	<mark.rutland@arm.com>
Cc: <linux-input@vger.kernel.org>, <devicetree@vger.kernel.org>,
	<linux-kernel@vger.kernel.org>,
	Richard Leitner <richard.leitner@skidata.com>
Subject: [PATCH 6/7] Input: sx8654 - add sx8650 support
Date: Tue, 16 Oct 2018 11:22:48 +0200	[thread overview]
Message-ID: <20181016092248.27288-1-richard.leitner@skidata.com> (raw)
In-Reply-To: <20181016091653.26896-1-richard.leitner@skidata.com>

The sx8654 and sx8650 are quite similar, therefore add support for the
sx8650 within the sx8654 driver.

Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
---
 drivers/input/touchscreen/sx8654.c | 186 ++++++++++++++++++++++++++++++++-----
 1 file changed, 163 insertions(+), 23 deletions(-)

diff --git a/drivers/input/touchscreen/sx8654.c b/drivers/input/touchscreen/sx8654.c
index 622283b49d7c..33f7a0be4ef8 100644
--- a/drivers/input/touchscreen/sx8654.c
+++ b/drivers/input/touchscreen/sx8654.c
@@ -29,12 +29,13 @@
 
 #include <linux/input.h>
 #include <linux/module.h>
-#include <linux/of.h>
+#include <linux/of_device.h>
 #include <linux/i2c.h>
 #include <linux/interrupt.h>
 #include <linux/irq.h>
 #include <linux/gpio/consumer.h>
 #include <linux/delay.h>
+#include <linux/hrtimer.h>
 
 /* register addresses */
 #define I2C_REG_TOUCH0			0x00
@@ -44,9 +45,11 @@
 #define I2C_REG_IRQSRC			0x23
 #define I2C_REG_SOFTRESET		0x3f
 
+#define I2C_REG_SX8650_STAT		0x05
+#define SX8650_STAT_CONVIRQ		BIT(7)
+
 /* commands */
 #define CMD_READ_REGISTER		0x40
-#define CMD_MANUAL			0xc0
 #define CMD_PENTRG			0xe0
 
 /* value for I2C_REG_SOFTRESET */
@@ -58,11 +61,12 @@
 
 /* bits for RegTouch1 */
 #define CONDIRQ				0x20
+#define RPDNT_100K			0x00
 #define FILT_7SA			0x03
 
 /* bits for I2C_REG_CHANMASK */
-#define CONV_X				0x80
-#define CONV_Y				0x40
+#define CONV_X				BIT(7)
+#define CONV_Y				BIT(6)
 
 /* coordinates rate: higher nibble of CTRL0 register */
 #define RATE_MANUAL			0x00
@@ -71,14 +75,110 @@
 /* power delay: lower nibble of CTRL0 register */
 #define POWDLY_1_1MS			0x0b
 
+/* for sx8650, as we have no pen release IRQ there: timeout in ns following the
+ * last PENIRQ after which we assume the pen is lifted.
+ */
+#define SX8650_PENIRQ_TIMEOUT		(80 * 1100 * 1000)
+
 #define MAX_12BIT			((1 << 12) - 1)
+#define MAX_I2C_READ_LEN		10 /* see datasheet section 5.1.5 */
+
+/* channel definition */
+#define CH_X				0x00
+#define CH_Y				0x01
+
+struct sx865x_data {
+	u8 cmd_manual;
+	u8 chan_mask;
+	u8 has_irq_penrelease;
+	u8 has_reg_irqmask;
+	irq_handler_t irqh;
+};
 
 struct sx8654 {
 	struct input_dev *input;
 	struct i2c_client *client;
 	struct gpio_desc *gpio_reset;
+	struct hrtimer timer;
+
+	const struct sx865x_data *data;
 };
 
+static enum hrtimer_restart sx865x_penrelease_timer_handler(struct hrtimer *h)
+{
+	struct sx8654 *ts = container_of(h, struct sx8654, timer);
+
+	input_report_key(ts->input, BTN_TOUCH, 0);
+	input_sync(ts->input);
+	dev_dbg(&ts->client->dev, "penrelease by timer\n");
+
+	return HRTIMER_NORESTART;
+}
+
+static irqreturn_t sx8650_irq(int irq, void *handle)
+{
+	struct sx8654 *ts = handle;
+	struct device *dev = &ts->client->dev;
+	int len, i, ret;
+	u8 stat;
+	u16 x, y;
+	u8 data[MAX_I2C_READ_LEN];
+	u16 ch;
+	u16 chdata;
+	u8 readlen = hweight32(ts->data->chan_mask) * 2;
+
+	stat = i2c_smbus_read_byte_data(ts->client, CMD_READ_REGISTER
+						    | I2C_REG_SX8650_STAT);
+
+	if (!(stat & SX8650_STAT_CONVIRQ)) {
+		dev_dbg(dev, "%s ignore stat [0x%02x]", __func__, stat);
+		return IRQ_HANDLED;
+	}
+
+	len = i2c_master_recv(ts->client, data, readlen);
+	if (len != readlen) {
+		dev_dbg(dev, "ignore short recv (%d)\n", len);
+		return IRQ_HANDLED;
+	}
+
+	ret = hrtimer_try_to_cancel(&ts->timer);
+
+	x = 0;
+	y = 0;
+	for (i = 0; (i + 1) < len; i++) {
+		chdata = data[i] << 8;
+		i++;
+		chdata += data[i];
+
+		if (unlikely(chdata == 0xFFFF)) {
+			dev_dbg(dev, "invalid qualified data @ %d\n", i);
+			continue;
+		} else if (unlikely(chdata & 0x8000)) {
+			dev_warn(dev, "hibit @ %d [0x%04x]\n", i, chdata);
+			continue;
+		}
+
+		ch = chdata >> 12;
+		if      (ch == CH_X)
+			x = chdata & MAX_12BIT;
+		else if (ch == CH_Y)
+			y = chdata & MAX_12BIT;
+		else
+			dev_warn(dev, "unknown channel %d [0x%04x]\n", ch,
+				 chdata);
+	}
+
+	input_report_abs(ts->input, ABS_X, x);
+	input_report_abs(ts->input, ABS_Y, y);
+	input_report_key(ts->input, BTN_TOUCH, 1);
+	input_sync(ts->input);
+	dev_dbg(dev, "point(%4d,%4d)\n", x, y);
+
+	hrtimer_start(&ts->timer, ktime_set(0, SX8650_PENIRQ_TIMEOUT),
+		      HRTIMER_MODE_REL);
+	return IRQ_HANDLED;
+}
+
 static irqreturn_t sx8654_irq(int irq, void *handle)
 {
 	struct sx8654 *sx8654 = handle;
@@ -127,6 +227,22 @@ static irqreturn_t sx8654_irq(int irq, void *handle)
 	return IRQ_HANDLED;
 }
 
+static const struct sx865x_data sx8650_data = {
+	.cmd_manual = 0xb0,
+	.has_irq_penrelease = 0,
+	.has_reg_irqmask = 0,
+	.chan_mask = (CONV_X | CONV_Y),
+	.irqh = sx8650_irq,
+};
+
+static const struct sx865x_data sx8654_data = {
+	.cmd_manual = 0xc0,
+	.has_irq_penrelease = 1,
+	.has_reg_irqmask = 1,
+	.chan_mask = (CONV_X | CONV_Y),
+	.irqh = sx8654_irq,
+};
+
 static int sx8654_reset(struct sx8654 *ts)
 {
 	int err;
@@ -182,13 +298,13 @@ static void sx8654_close(struct input_dev *dev)
 	disable_irq(client->irq);
 
 	/* enable manual mode mode */
-	error = i2c_smbus_write_byte(client, CMD_MANUAL);
+	error = i2c_smbus_write_byte(client, sx8654->data->cmd_manual);
 	if (error) {
 		dev_err(&client->dev, "writing command CMD_MANUAL failed");
 		return;
 	}
 
-	error = i2c_smbus_write_byte_data(client, I2C_REG_TOUCH0, 0);
+	error = i2c_smbus_write_byte_data(client, I2C_REG_TOUCH0, RATE_MANUAL);
 	if (error) {
 		dev_err(&client->dev, "writing to I2C_REG_TOUCH0 failed");
 		return;
@@ -196,10 +312,30 @@ static void sx8654_close(struct input_dev *dev)
 }
 
 #ifdef CONFIG_OF
+static const struct of_device_id sx8654_of_match[] = {
+	{
+		.compatible = "semtech,sx8650",
+		.data = &sx8650_data,
+	}, {
+		.compatible = "semtech,sx8654",
+		.data = &sx8654_data,
+	}, {
+		.compatible = "semtech,sx8655",
+		.data = &sx8654_data,
+	}, {
+		.compatible = "semtech,sx8656",
+		.data = &sx8654_data,
+	}, {},
+};
+MODULE_DEVICE_TABLE(of, sx8654_of_match);
+
 static int sx8654_get_ofdata(struct sx8654 *ts)
 {
 	struct device *dev = &ts->client->dev;
 	struct device_node *node = dev->of_node;
+	const struct of_device_id *of_id = of_match_device(sx8654_of_match,
+							   dev);
+	const struct sx865x_data *data = (struct sx865x_data *)of_id->data;
 	int err;
 
 	if (!node) {
@@ -207,6 +343,8 @@ static int sx8654_get_ofdata(struct sx8654 *ts)
 		return 0;
 	}
 
+	ts->data = data;
+
 	ts->gpio_reset = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_HIGH);
 	if (PTR_ERR(ts->gpio_reset) == -EPROBE_DEFER) {
 		return -EPROBE_DEFER;
@@ -219,18 +357,11 @@ static int sx8654_get_ofdata(struct sx8654 *ts)
 
 	return 0;
 }
-
-static const struct of_device_id sx8654_of_match[] = {
-	{ .compatible = "semtech,sx8654", },
-	{ .compatible = "semtech,sx8655", },
-	{ .compatible = "semtech,sx8656", },
-	{ },
-};
-MODULE_DEVICE_TABLE(of, sx8654_of_match);
 #else /* CONFIG_OF */
 static int sx8654_get_ofdata(struct sx8654 *ts)
 {
 	ts->gpio_reset = NULL;
+	ts->data = &sx8654_data;
 	return 0;
 }
 #endif /* CONFIG_OF */
@@ -258,6 +389,12 @@ static int sx8654_probe(struct i2c_client *client,
 		return error;
 	}
 
+	if (!sx8654->data->has_irq_penrelease) {
+		dev_dbg(&client->dev, "use timer for penrelease\n");
+		hrtimer_init(&sx8654->timer, CLOCK_MONOTONIC, HRTIMER_MODE_REL);
+		sx8654->timer.function = sx865x_penrelease_timer_handler;
+	}
+
 	input = devm_input_allocate_device(&client->dev);
 	if (!input)
 		return -ENOMEM;
@@ -284,29 +421,31 @@ static int sx8654_probe(struct i2c_client *client,
 	}
 
 	error = i2c_smbus_write_byte_data(client, I2C_REG_CHANMASK,
-					  CONV_X | CONV_Y);
+					  sx8654->data->chan_mask);
 	if (error) {
 		dev_err(&client->dev, "writing to I2C_REG_CHANMASK failed");
 		return error;
 	}
 
-	error = i2c_smbus_write_byte_data(client, I2C_REG_IRQMASK,
-					  IRQ_PENTOUCH_TOUCHCONVDONE |
-						IRQ_PENRELEASE);
-	if (error) {
-		dev_err(&client->dev, "writing to I2C_REG_IRQMASK failed");
-		return error;
+	if (sx8654->data->has_reg_irqmask) {
+		error = i2c_smbus_write_byte_data(client, I2C_REG_IRQMASK,
+						  IRQ_PENTOUCH_TOUCHCONVDONE |
+							IRQ_PENRELEASE);
+		if (error) {
+			dev_err(&client->dev, "writing I2C_REG_IRQMASK failed");
+			return error;
+		}
 	}
 
 	error = i2c_smbus_write_byte_data(client, I2C_REG_TOUCH1,
-					  CONDIRQ | FILT_7SA);
+					  CONDIRQ | RPDNT_100K | FILT_7SA);
 	if (error) {
 		dev_err(&client->dev, "writing to I2C_REG_TOUCH1 failed");
 		return error;
 	}
 
 	error = devm_request_threaded_irq(&client->dev, client->irq,
-					  NULL, sx8654_irq,
+					  NULL, sx8654->data->irqh,
 					  IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
 					  client->name, sx8654);
 	if (error) {
@@ -327,6 +466,7 @@ static int sx8654_probe(struct i2c_client *client,
 }
 
 static const struct i2c_device_id sx8654_id_table[] = {
+	{ "semtech_sx8650", 0 },
 	{ "semtech_sx8654", 0 },
 	{ "semtech_sx8655", 0 },
 	{ "semtech_sx8656", 0 },
-- 
2.11.0


  parent reply	other threads:[~2018-10-16  9:24 UTC|newest]

Thread overview: 14+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2018-10-16  9:16 [PATCH 0/7] Input: sx8654 - reset-gpio, sx865[056] support, etc Richard Leitner
2018-10-16  9:16 ` [PATCH 1/7] dt-bindings: input: touchscreen: sx8654: add reset-gpio property Richard Leitner
2018-10-16  9:16 ` [PATCH 2/7] Input: sx8654 - add reset-gpio support Richard Leitner
2018-10-16 17:39   ` Dmitry Torokhov
2018-10-16 19:32     ` Richard Leitner
2018-10-16  9:16 ` [PATCH 3/7] dt-bindings: input: touchscreen: sx8654: add compatible models Richard Leitner
2018-10-16  9:16 ` [PATCH 4/7] Input: sx8654 - add sx8655 and sx8656 to compatibles Richard Leitner
2018-10-16  9:22 ` [PATCH 5/7] dt-bindings: input: touchscreen: sx8654: add sx8650 to comatibles Richard Leitner
2018-10-16  9:22 ` Richard Leitner [this message]
2018-10-16 17:48   ` [PATCH 6/7] Input: sx8654 - add sx8650 support Dmitry Torokhov
2018-10-16 19:34     ` Richard Leitner
2018-10-16 20:18       ` Dmitry Torokhov
2018-10-16  9:23 ` [PATCH 7/7] Input: sx8654 - use common of_touchscreen functions Richard Leitner
2018-10-16 17:52   ` Dmitry Torokhov

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20181016092248.27288-1-richard.leitner@skidata.com \
    --to=richard.leitner@skidata.com \
    --cc=devicetree@vger.kernel.org \
    --cc=dmitry.torokhov@gmail.com \
    --cc=linux-input@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=mark.rutland@arm.com \
    --cc=robh+dt@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).