From: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
To: grygorii.strashko@ti.com, davem@davemloft.net
Cc: linux-omap@vger.kernel.org, netdev@vger.kernel.org,
linux-kernel@vger.kernel.org, alexander.h.duyck@intel.com,
bjorn@mork.no, Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Subject: [PATCH v2 net-next 3/4] net: ethernet: ti: cpsw: fix vlan mcast
Date: Thu, 8 Nov 2018 22:27:56 +0200 [thread overview]
Message-ID: <20181108202757.30110-4-ivan.khoronzhuk@linaro.org> (raw)
In-Reply-To: <20181108202757.30110-1-ivan.khoronzhuk@linaro.org>
At this moment, mcast addresses are added for real device only
(reserved vlans for dual-emac mode), even if a mcast address was added
for some vlan only, thus ALE doesn't have corresponding vlan mcast
entries after vlan socket joined multicast group. So ALE drops vlan
frames with mcast addresses intended for vlans and potentially can
receive mcast frames for base ndev. That's not correct. So, fix it by
creating only vlan/mcast entries as requested. Patch doesn't use any
additional lists and is based on device mc address list and cpsw ALE
table entries.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
---
drivers/net/ethernet/ti/cpsw.c | 169 +++++++++++++++++++++++++++------
1 file changed, 138 insertions(+), 31 deletions(-)
diff --git a/drivers/net/ethernet/ti/cpsw.c b/drivers/net/ethernet/ti/cpsw.c
index 500f7ed8c58c..0b18634d336c 100644
--- a/drivers/net/ethernet/ti/cpsw.c
+++ b/drivers/net/ethernet/ti/cpsw.c
@@ -570,21 +570,6 @@ static inline int cpsw_get_slave_port(u32 slave_num)
return slave_num + 1;
}
-static void cpsw_add_mcast(struct cpsw_priv *priv, const u8 *addr)
-{
- struct cpsw_common *cpsw = priv->cpsw;
-
- if (cpsw->data.dual_emac) {
- struct cpsw_slave *slave = cpsw->slaves + priv->emac_port;
-
- cpsw_ale_add_mcast(cpsw->ale, addr, ALE_PORT_HOST,
- ALE_VLAN, slave->port_vlan, 0);
- return;
- }
-
- cpsw_ale_add_mcast(cpsw->ale, addr, ALE_ALL_PORTS, 0, 0, 0);
-}
-
static void cpsw_set_promiscious(struct net_device *ndev, bool enable)
{
struct cpsw_common *cpsw = ndev_to_cpsw(ndev);
@@ -640,7 +625,7 @@ static void cpsw_set_promiscious(struct net_device *ndev, bool enable)
/* Clear all mcast from ALE */
cpsw_ale_flush_multicast(ale, ALE_ALL_PORTS, -1);
- __dev_mc_unsync(ndev, NULL);
+ __hw_addr_ref_unsync_dev(&ndev->mc, ndev, NULL);
/* Flood All Unicast Packets to Host port */
cpsw_ale_control_set(ale, 0, ALE_P0_UNI_FLOOD, 1);
@@ -661,29 +646,148 @@ static void cpsw_set_promiscious(struct net_device *ndev, bool enable)
}
}
-static int cpsw_add_mc_addr(struct net_device *ndev, const u8 *addr)
+struct addr_sync_ctx {
+ struct net_device *ndev;
+ const u8 *addr; /* address to be synched */
+ int consumed; /* number of address instances */
+ int flush; /* flush flag */
+};
+
+/**
+ * cpsw_set_mc - adds multicast entry to the table if it's not added or deletes
+ * if it's not deleted
+ * @ndev: device to sync
+ * @addr: address to be added or deleted
+ * @vid: vlan id, if vid < 0 set/unset address for real device
+ * @add: add address if the flag is set or remove otherwise
+ */
+static int cpsw_set_mc(struct net_device *ndev, const u8 *addr,
+ int vid, int add)
{
struct cpsw_priv *priv = netdev_priv(ndev);
+ struct cpsw_common *cpsw = priv->cpsw;
+ int mask, flags, ret;
+
+ if (vid < 0) {
+ if (cpsw->data.dual_emac)
+ vid = cpsw->slaves[priv->emac_port].port_vlan;
+ else
+ vid = 0;
+ }
+
+ mask = cpsw->data.dual_emac ? ALE_PORT_HOST : ALE_ALL_PORTS;
+ flags = vid ? ALE_VLAN : 0;
+
+ if (add)
+ ret = cpsw_ale_add_mcast(cpsw->ale, addr, mask, flags, vid, 0);
+ else
+ ret = cpsw_ale_del_mcast(cpsw->ale, addr, 0, flags, vid);
+
+ return ret;
+}
+
+static int cpsw_update_vlan_mc(struct net_device *vdev, int vid, void *ctx)
+{
+ struct addr_sync_ctx *sync_ctx = ctx;
+ struct netdev_hw_addr *ha;
+ int found = 0, ret = 0;
+
+ if (!vdev || !(vdev->flags & IFF_UP))
+ return 0;
+
+ /* vlan address is relevant if its sync_cnt != 0 */
+ netdev_for_each_mc_addr(ha, vdev) {
+ if (ether_addr_equal(ha->addr, sync_ctx->addr)) {
+ found = ha->sync_cnt;
+ break;
+ }
+ }
+
+ if (found)
+ sync_ctx->consumed++;
+
+ if (sync_ctx->flush) {
+ if (!found)
+ cpsw_set_mc(sync_ctx->ndev, sync_ctx->addr, vid, 0);
+ return 0;
+ }
+
+ if (found)
+ ret = cpsw_set_mc(sync_ctx->ndev, sync_ctx->addr, vid, 1);
+
+ return ret;
+}
+
+static int cpsw_add_mc_addr(struct net_device *ndev, const u8 *addr, int num)
+{
+ struct addr_sync_ctx sync_ctx;
+ int ret;
+
+ sync_ctx.consumed = 0;
+ sync_ctx.addr = addr;
+ sync_ctx.ndev = ndev;
+ sync_ctx.flush = 0;
+
+ ret = vlan_for_each(ndev, cpsw_update_vlan_mc, &sync_ctx);
+ if (sync_ctx.consumed < num && !ret)
+ ret = cpsw_set_mc(ndev, addr, -1, 1);
+
+ return ret;
+}
+
+static int cpsw_del_mc_addr(struct net_device *ndev, const u8 *addr, int num)
+{
+ struct addr_sync_ctx sync_ctx;
+
+ sync_ctx.consumed = 0;
+ sync_ctx.addr = addr;
+ sync_ctx.ndev = ndev;
+ sync_ctx.flush = 1;
+
+ vlan_for_each(ndev, cpsw_update_vlan_mc, &sync_ctx);
+ if (sync_ctx.consumed == num)
+ cpsw_set_mc(ndev, addr, -1, 0);
- cpsw_add_mcast(priv, addr);
return 0;
}
-static int cpsw_del_mc_addr(struct net_device *ndev, const u8 *addr)
+static int cpsw_purge_vlan_mc(struct net_device *vdev, int vid, void *ctx)
{
- struct cpsw_priv *priv = netdev_priv(ndev);
- struct cpsw_common *cpsw = priv->cpsw;
- int vid, flags;
+ struct addr_sync_ctx *sync_ctx = ctx;
+ struct netdev_hw_addr *ha;
+ int found = 0;
- if (cpsw->data.dual_emac) {
- vid = cpsw->slaves[priv->emac_port].port_vlan;
- flags = ALE_VLAN;
- } else {
- vid = 0;
- flags = 0;
+ if (!vdev || !(vdev->flags & IFF_UP))
+ return 0;
+
+ /* vlan address is relevant if its sync_cnt != 0 */
+ netdev_for_each_mc_addr(ha, vdev) {
+ if (ether_addr_equal(ha->addr, sync_ctx->addr)) {
+ found = ha->sync_cnt;
+ break;
+ }
}
- cpsw_ale_del_mcast(cpsw->ale, addr, 0, flags, vid);
+ if (!found)
+ return 0;
+
+ sync_ctx->consumed++;
+ cpsw_set_mc(sync_ctx->ndev, sync_ctx->addr, vid, 0);
+ return 0;
+}
+
+static int cpsw_purge_all_mc(struct net_device *ndev, const u8 *addr, int num)
+{
+ struct addr_sync_ctx sync_ctx;
+
+ sync_ctx.addr = addr;
+ sync_ctx.ndev = ndev;
+ sync_ctx.consumed = 0;
+
+ vlan_for_each(ndev, cpsw_purge_vlan_mc, &sync_ctx);
+ if (sync_ctx.consumed < num)
+ cpsw_set_mc(ndev, addr, -1, 0);
+
return 0;
}
@@ -704,7 +808,9 @@ static void cpsw_ndo_set_rx_mode(struct net_device *ndev)
/* Restore allmulti on vlans if necessary */
cpsw_ale_set_allmulti(cpsw->ale, ndev->flags & IFF_ALLMULTI);
- __dev_mc_sync(ndev, cpsw_add_mc_addr, cpsw_del_mc_addr);
+ /* add/remove mcast address either for real netdev or for vlan */
+ __hw_addr_ref_sync_dev(&ndev->mc, ndev, cpsw_add_mc_addr,
+ cpsw_del_mc_addr);
}
static void cpsw_intr_enable(struct cpsw_common *cpsw)
@@ -1964,7 +2070,7 @@ static int cpsw_ndo_stop(struct net_device *ndev)
struct cpsw_common *cpsw = priv->cpsw;
cpsw_info(priv, ifdown, "shutting down cpsw device\n");
- __dev_mc_unsync(priv->ndev, cpsw_del_mc_addr);
+ __hw_addr_ref_unsync_dev(&ndev->mc, ndev, cpsw_purge_all_mc);
netif_tx_stop_all_queues(priv->ndev);
netif_carrier_off(priv->ndev);
@@ -2415,6 +2521,7 @@ static int cpsw_ndo_vlan_rx_kill_vid(struct net_device *ndev,
HOST_PORT_NUM, ALE_VLAN, vid);
ret |= cpsw_ale_del_mcast(cpsw->ale, priv->ndev->broadcast,
0, ALE_VLAN, vid);
+ ret |= cpsw_ale_flush_multicast(cpsw->ale, 0, vid);
err:
pm_runtime_put(cpsw->dev);
return ret;
--
2.17.1
next prev parent reply other threads:[~2018-11-08 20:31 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-11-08 20:27 [PATCH v2 net-next 0/4] net: ethernet: ti: cpsw: fix vlan mcast Ivan Khoronzhuk
2018-11-08 20:27 ` [PATCH v2 net-next 1/4] net: core: dev_addr_lists: add auxiliary func to handle reference address updates Ivan Khoronzhuk
2018-11-08 20:27 ` [PATCH v2 net-next 2/4] net: 8021q: vlan_core: allow use list of vlans for real device Ivan Khoronzhuk
2018-11-08 20:27 ` Ivan Khoronzhuk [this message]
2018-11-08 20:27 ` [PATCH v2 net-next 4/4] net: ethernet: ti: cpsw: fix vlan configuration while down/up Ivan Khoronzhuk
2018-11-09 4:32 ` [PATCH v2 net-next 0/4] net: ethernet: ti: cpsw: fix vlan mcast David Miller
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20181108202757.30110-4-ivan.khoronzhuk@linaro.org \
--to=ivan.khoronzhuk@linaro.org \
--cc=alexander.h.duyck@intel.com \
--cc=bjorn@mork.no \
--cc=davem@davemloft.net \
--cc=grygorii.strashko@ti.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-omap@vger.kernel.org \
--cc=netdev@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).