From: Bjorn Andersson <bjorn.andersson@linaro.org>
To: Andy Gross <andy.gross@linaro.org>, David Brown <david.brown@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>,
Mark Rutland <mark.rutland@arm.com>,
linux-arm-msm@vger.kernel.org, linux-soc@vger.kernel.org,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org
Subject: [PATCH 3/3] arm64: dts: qcom: qcs404: Add QUP I2C and SPI nodes
Date: Sun, 18 Nov 2018 12:01:35 -0800 [thread overview]
Message-ID: <20181118200135.25258-4-bjorn.andersson@linaro.org> (raw)
In-Reply-To: <20181118200135.25258-1-bjorn.andersson@linaro.org>
Define all six QUP controllers, both as SPI and I2C, allowing boards to
enable these as needed. Associated pinmux states are also defined, to
require only pinconf states to be specified by the boards, as they are
enabled.
Note that SPI has not been tested.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
---
arch/arm64/boot/dts/qcom/qcs404.dtsi | 235 +++++++++++++++++++++++++++
1 file changed, 235 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/qcs404.dtsi b/arch/arm64/boot/dts/qcom/qcs404.dtsi
index ca00987d6400..9d78183cbdd8 100644
--- a/arch/arm64/boot/dts/qcom/qcs404.dtsi
+++ b/arch/arm64/boot/dts/qcom/qcs404.dtsi
@@ -273,6 +273,38 @@
interrupt-controller;
#interrupt-cells = <2>;
+ blsp1_i2c0_default: blsp1-i2c0-default {
+ pins = "gpio32", "gpio33";
+ function = "blsp_i2c0";
+ };
+
+ blsp1_i2c1_default: blsp1-i2c1-default {
+ pins = "gpio24", "gpio25";
+ function = "blsp_i2c1";
+ };
+
+ blsp1_i2c2_default: blsp1-i2c2-default {
+ sda {
+ pins = "gpio19";
+ function = "blsp_i2c_sda_a2";
+ };
+
+ scl {
+ pins = "gpio20";
+ function = "blsp_i2c_scl_a2";
+ };
+ };
+
+ blsp1_i2c3_default: blsp1-i2c3-default {
+ pins = "gpio84", "gpio85";
+ function = "blsp_i2c3";
+ };
+
+ blsp1_i2c4_default: blsp1-i2c4-default {
+ pins = "gpio117", "gpio118";
+ function = "blsp_i2c4";
+ };
+
blsp1_uart0_default: blsp1-uart0-default {
pins = "gpio30", "gpio31", "gpio32", "gpio33";
function = "blsp_uart0";
@@ -300,6 +332,41 @@
function = "blsp_uart3";
};
+ blsp2_i2c0_default: blsp2-i2c0-default {
+ pins = "gpio28", "gpio29";
+ function = "blsp_i2c5";
+ };
+
+ blsp1_spi0_default: blsp1-spi0-default {
+ pins = "gpio30", "gpio31", "gpio32", "gpio33";
+ function = "blsp_spi0";
+ };
+
+ blsp1_spi1_default: blsp1-spi1-default {
+ pins = "gpio22", "gpio23", "gpio24", "gpio25";
+ function = "blsp_spi1";
+ };
+
+ blsp1_spi2_default: blsp1-spi2-default {
+ pins = "gpio17", "gpio18", "gpio19", "gpio20";
+ function = "blsp_spi2";
+ };
+
+ blsp1_spi3_default: blsp1-spi3-default {
+ pins = "gpio82", "gpio83", "gpio84", "gpio85";
+ function = "blsp_spi3";
+ };
+
+ blsp1_spi4_default: blsp1-spi4-default {
+ pins = "gpio37", "gpio38", "gpio117", "gpio118";
+ function = "blsp_spi4";
+ };
+
+ blsp2_spi0_default: blsp2-spi0-default {
+ pins = "gpio26", "gpio27", "gpio28", "gpio29";
+ function = "blsp_spi5";
+ };
+
blsp2_uart0_default: blsp2-uart0-default {
pins = "gpio26", "gpio27", "gpio28", "gpio29";
function = "blsp_uart5";
@@ -419,6 +486,146 @@
status = "disabled";
};
+ blsp1_i2c0: i2c@78b5000 {
+ compatible = "qcom,i2c-qup-v2.2.1";
+ reg = <0x078b5000 0x600>;
+ interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_AHB_CLK>,
+ <&gcc GCC_BLSP1_QUP0_I2C_APPS_CLK>;
+ clock-names = "iface", "core";
+ pinctrl-names = "default";
+ pinctrl-0 = <&blsp1_i2c0_default>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ blsp1_spi0: spi@78b5000 {
+ compatible = "qcom,spi-qup-v2.2.1";
+ reg = <0x078b5000 0x600>;
+ interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_AHB_CLK>,
+ <&gcc GCC_BLSP1_QUP0_SPI_APPS_CLK>;
+ clock-names = "iface", "core";
+ pinctrl-names = "default";
+ pinctrl-0 = <&blsp1_spi0_default>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ blsp1_i2c1: i2c@78b6000 {
+ compatible = "qcom,i2c-qup-v2.2.1";
+ reg = <0x078b6000 0x600>;
+ interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_AHB_CLK>,
+ <&gcc GCC_BLSP1_QUP1_I2C_APPS_CLK>;
+ clock-names = "iface", "core";
+ pinctrl-names = "default";
+ pinctrl-0 = <&blsp1_i2c1_default>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ blsp1_spi1: spi@78b6000 {
+ compatible = "qcom,spi-qup-v2.2.1";
+ reg = <0x078b6000 0x600>;
+ interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_AHB_CLK>,
+ <&gcc GCC_BLSP1_QUP1_SPI_APPS_CLK>;
+ clock-names = "iface", "core";
+ pinctrl-names = "default";
+ pinctrl-0 = <&blsp1_spi1_default>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ blsp1_i2c2: i2c@78b7000 {
+ compatible = "qcom,i2c-qup-v2.2.1";
+ reg = <0x078b7000 0x600>;
+ interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_AHB_CLK>,
+ <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>;
+ clock-names = "iface", "core";
+ pinctrl-names = "default";
+ pinctrl-0 = <&blsp1_i2c2_default>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ blsp1_spi2: spi@78b7000 {
+ compatible = "qcom,spi-qup-v2.2.1";
+ reg = <0x078b7000 0x600>;
+ interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_AHB_CLK>,
+ <&gcc GCC_BLSP1_QUP2_SPI_APPS_CLK>;
+ clock-names = "iface", "core";
+ pinctrl-names = "default";
+ pinctrl-0 = <&blsp1_spi2_default>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ blsp1_i2c3: i2c@78b8000 {
+ compatible = "qcom,i2c-qup-v2.2.1";
+ reg = <0x078b8000 0x600>;
+ interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_AHB_CLK>,
+ <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>;
+ clock-names = "iface", "core";
+ pinctrl-names = "default";
+ pinctrl-0 = <&blsp1_i2c3_default>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ blsp1_spi3: spi@78b8000 {
+ compatible = "qcom,spi-qup-v2.2.1";
+ reg = <0x078b8000 0x600>;
+ interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_AHB_CLK>,
+ <&gcc GCC_BLSP1_QUP3_SPI_APPS_CLK>;
+ clock-names = "iface", "core";
+ pinctrl-names = "default";
+ pinctrl-0 = <&blsp1_spi3_default>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ blsp1_i2c4: i2c@78b9000 {
+ compatible = "qcom,i2c-qup-v2.2.1";
+ reg = <0x078b9000 0x600>;
+ interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_AHB_CLK>,
+ <&gcc GCC_BLSP1_QUP4_I2C_APPS_CLK>;
+ clock-names = "iface", "core";
+ pinctrl-names = "default";
+ pinctrl-0 = <&blsp1_i2c4_default>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ blsp1_spi4: spi@78b9000 {
+ compatible = "qcom,spi-qup-v2.2.1";
+ reg = <0x078b9000 0x600>;
+ interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_AHB_CLK>,
+ <&gcc GCC_BLSP1_QUP4_SPI_APPS_CLK>;
+ clock-names = "iface", "core";
+ pinctrl-names = "default";
+ pinctrl-0 = <&blsp1_spi4_default>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
blsp2_dma: dma@7ac4000 {
compatible = "qcom,bam-v1.7.0";
reg = <0x07ac4000 0x17000>;
@@ -444,6 +651,34 @@
status = "disabled";
};
+ blsp2_i2c0: i2c@7af5000 {
+ compatible = "qcom,i2c-qup-v2.2.1";
+ reg = <0x07af5000 0x600>;
+ interrupts = <GIC_SPI 299 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP2_AHB_CLK>,
+ <&gcc GCC_BLSP2_QUP0_I2C_APPS_CLK>;
+ clock-names = "iface", "core";
+ pinctrl-names = "default";
+ pinctrl-0 = <&blsp2_i2c0_default>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ blsp2_spi0: spi@7af5000 {
+ compatible = "qcom,spi-qup-v2.2.1";
+ reg = <0x07af5000 0x600>;
+ interrupts = <GIC_SPI 299 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP2_AHB_CLK>,
+ <&gcc GCC_BLSP2_QUP0_SPI_APPS_CLK>;
+ clock-names = "iface", "core";
+ pinctrl-names = "default";
+ pinctrl-0 = <&blsp2_spi0_default>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
intc: interrupt-controller@b000000 {
compatible = "qcom,msm-qgic2";
interrupt-controller;
--
2.18.0
next prev parent reply other threads:[~2018-11-18 20:04 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-11-18 20:01 [PATCH 0/3] arm64: dts: qcom: QCS404 BLSP nodes Bjorn Andersson
2018-11-18 20:01 ` [PATCH 1/3] arm64: dts: qcom: qcs404: Specify pinctrl state for UART Bjorn Andersson
2018-11-18 20:01 ` [PATCH 2/3] arm64: dts: qcom: qcs404: Define remaining UARTs Bjorn Andersson
2018-11-18 20:01 ` Bjorn Andersson [this message]
2018-11-29 14:34 ` [PATCH 0/3] arm64: dts: qcom: QCS404 BLSP nodes Vinod Koul
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20181118200135.25258-4-bjorn.andersson@linaro.org \
--to=bjorn.andersson@linaro.org \
--cc=andy.gross@linaro.org \
--cc=david.brown@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-soc@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).