From: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
To: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>,
Bjorn Helgaas <bhelgaas@google.com>,
Rob Herring <robh+dt@kernel.org>,
Mark Rutland <mark.rutland@arm.com>,
Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: linux-pci@vger.kernel.org, devicetree@vger.kernel.org,
linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org,
Masami Hiramatsu <masami.hiramatsu@linaro.org>,
Jassi Brar <jaswinder.singh@linaro.org>,
Gustavo Pimentel <gustavo.pimentel@synopsys.com>,
Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Subject: [PATCH v4 1/2] dt-bindings: PCI: Add UniPhier PCIe host controller description
Date: Wed, 28 Nov 2018 13:04:25 +0900 [thread overview]
Message-ID: <1543377866-16634-2-git-send-email-hayashi.kunihiko@socionext.com> (raw)
In-Reply-To: <1543377866-16634-1-git-send-email-hayashi.kunihiko@socionext.com>
Add DT bindings for PCIe controller implemented in UniPhier SoCs when
configured in Root Complex (host) mode. This controller is based on
the DesignWare PCIe core.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
.../devicetree/bindings/pci/uniphier-pcie.txt | 81 ++++++++++++++++++++++
1 file changed, 81 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pci/uniphier-pcie.txt
diff --git a/Documentation/devicetree/bindings/pci/uniphier-pcie.txt b/Documentation/devicetree/bindings/pci/uniphier-pcie.txt
new file mode 100644
index 0000000..1fa2c59
--- /dev/null
+++ b/Documentation/devicetree/bindings/pci/uniphier-pcie.txt
@@ -0,0 +1,81 @@
+Socionext UniPhier PCIe host controller bindings
+
+This describes the devicetree bindings for PCIe host controller implemented
+on Socionext UniPhier SoCs.
+
+UniPhier PCIe host controller is based on the Synopsys DesignWare PCI core.
+It shares common functions with the PCIe DesignWare core driver and inherits
+common properties defined in
+Documentation/devicetree/bindings/pci/designware-pcie.txt.
+
+Required properties:
+- compatible: Should be "socionext,uniphier-pcie".
+- reg: Specifies offset and length of the register set for the device.
+ According to the reg-names, appropriate register sets are required.
+- reg-names: Must include the following entries:
+ "dbi" - controller configuration registers
+ "link" - SoC-specific glue layer registers
+ "config" - PCIe configuration space
+- clocks: A phandle to the clock gate for PCIe glue layer including
+ the host controller.
+- resets: A phandle to the reset line for PCIe glue layer including
+ the host controller.
+- interrupts: A list of interrupt specifiers. According to the
+ interrupt-names, appropriate interrupts are required.
+- interrupt-names: Must include the following entries:
+ "dma" - DMA interrupt
+ "msi" - MSI interrupt
+
+Optional properties:
+- phys: A phandle to generic PCIe PHY. According to the phy-names, appropriate
+ phys are required.
+- phy-names: Must be "pcie-phy".
+
+Required sub-node:
+- legacy-interrupt-controller: Specifies interrupt controller for legacy PCI
+ interrupts.
+
+Required properties for legacy-interrupt-controller:
+- interrupt-controller: identifies the node as an interrupt controller.
+- #interrupt-cells: specifies the number of cells needed to encode an
+ interrupt source. The value must be 1.
+- interrupt-parent: Phandle to the parent interrupt controller.
+- interrupts: An interrupt specifier for legacy interrupt.
+
+Example:
+
+ pcie: pcie@66000000 {
+ compatible = "socionext,uniphier-pcie", "snps,dw-pcie";
+ status = "disabled";
+ reg-names = "dbi", "link", "config";
+ reg = <0x66000000 0x1000>, <0x66010000 0x10000>,
+ <0x2fff0000 0x10000>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ clocks = <&sys_clk 24>;
+ resets = <&sys_rst 24>;
+ num-lanes = <1>;
+ num-viewport = <1>;
+ bus-range = <0x0 0xff>;
+ device_type = "pci";
+ ranges =
+ /* downstream I/O */
+ <0x81000000 0 0x00000000 0x2ffe0000 0 0x00010000
+ /* non-prefetchable memory */
+ 0x82000000 0 0x00000000 0x20000000 0 0x0ffe0000>;
+ #interrupt-cells = <1>;
+ interrupt-names = "dma", "msi";
+ interrupts = <0 224 4>, <0 225 4>;
+ interrupt-map-mask = <0 0 0 7>;
+ interrupt-map = <0 0 0 1 &pcie_intc 0>, /* INTA */
+ <0 0 0 2 &pcie_intc 1>, /* INTB */
+ <0 0 0 3 &pcie_intc 2>, /* INTC */
+ <0 0 0 4 &pcie_intc 3>; /* INTD */
+
+ pcie_intc: legacy-interrupt-controller {
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ interrupt-parent = <&gic>;
+ interrupts = <0 226 4>;
+ };
+ };
--
2.7.4
next prev parent reply other threads:[~2018-11-28 4:04 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-11-28 4:04 [PATCH v4 0/2] Add new UniPhier PCIe host driver Kunihiko Hayashi
2018-11-28 4:04 ` Kunihiko Hayashi [this message]
2018-11-28 4:04 ` [PATCH v4 2/2] PCI: uniphier: Add UniPhier PCIe host controller support Kunihiko Hayashi
2018-12-04 15:12 ` Lorenzo Pieralisi
2018-12-05 2:13 ` Kunihiko Hayashi
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1543377866-16634-2-git-send-email-hayashi.kunihiko@socionext.com \
--to=hayashi.kunihiko@socionext.com \
--cc=bhelgaas@google.com \
--cc=devicetree@vger.kernel.org \
--cc=gustavo.pimentel@synopsys.com \
--cc=jaswinder.singh@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pci@vger.kernel.org \
--cc=lorenzo.pieralisi@arm.com \
--cc=mark.rutland@arm.com \
--cc=masami.hiramatsu@linaro.org \
--cc=robh+dt@kernel.org \
--cc=yamada.masahiro@socionext.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).