From: Anson Huang <anson.huang@nxp.com>
To: "shawnguo@kernel.org" <shawnguo@kernel.org>,
"s.hauer@pengutronix.de" <s.hauer@pengutronix.de>,
"kernel@pengutronix.de" <kernel@pengutronix.de>,
Fabio Estevam <fabio.estevam@nxp.com>,
"robh+dt@kernel.org" <robh+dt@kernel.org>,
"mark.rutland@arm.com" <mark.rutland@arm.com>,
"mturquette@baylibre.com" <mturquette@baylibre.com>,
"sboyd@kernel.org" <sboyd@kernel.org>,
Aisheng Dong <aisheng.dong@nxp.com>,
"linux-arm-kernel@lists.infradead.org"
<linux-arm-kernel@lists.infradead.org>,
"devicetree@vger.kernel.org" <devicetree@vger.kernel.org>,
"linux-kernel@vger.kernel.org" <linux-kernel@vger.kernel.org>,
"linux-clk@vger.kernel.org" <linux-clk@vger.kernel.org>
Cc: dl-linux-imx <linux-imx@nxp.com>
Subject: [PATCH 2/3] clk: imx: imx7ulp: add arm hsrun mode clocks support
Date: Fri, 7 Dec 2018 10:03:34 +0000 [thread overview]
Message-ID: <1544176659-32022-2-git-send-email-Anson.Huang@nxp.com> (raw)
In-Reply-To: <1544176659-32022-1-git-send-email-Anson.Huang@nxp.com>
i.MX7ULP has a Cortex-A7 CPU which can run in RUN mode
or HSRUN mode, it is controlled in SMC1 module. The RUN
mode and HSRUN mode will use different clock source for
ARM, "divcore" for RUN mode and "hsrun_divcore" for HSRUN
mode, so the control bits in SMC1 module can be abstracted
as a HW clock mux, this patch adds HSRUN mode related
clocks in SCG1 module and adds "arm" clock in SMC1 module
to support RUN mode and HSRUN mode switch.
Latest clock tree in RUN mode as below:
firc 0 0 0 48000000 0 0 50000
firc_bus_clk 0 0 0 48000000 0 0 50000
hsrun_scs_sel 0 0 0 48000000 0 0 50000
hsrun_divcore 0 0 0 48000000 0 0 50000
sosc 3 3 3 24000000 0 0 50000
spll_pre_sel 1 1 1 24000000 0 0 50000
spll_pre_div 1 1 2 24000000 0 0 50000
spll 1 1 2 528000000 0 0 50000
spll_pfd0 1 1 1 500210526 0 0 50000
spll_pfd_sel 1 1 0 500210526 0 0 50000
spll_sel 1 1 0 500210526 0 0 50000
scs_sel 1 1 0 500210526 0 0 50000
divcore 1 1 0 500210526 0 0 50000
arm 1 1 0 500210526 0 0 50000
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
---
drivers/clk/imx/clk-imx7ulp.c | 31 ++++++++++++++++++++++++++++++-
1 file changed, 30 insertions(+), 1 deletion(-)
diff --git a/drivers/clk/imx/clk-imx7ulp.c b/drivers/clk/imx/clk-imx7ulp.c
index 3b7507f..4e18f62 100644
--- a/drivers/clk/imx/clk-imx7ulp.c
+++ b/drivers/clk/imx/clk-imx7ulp.c
@@ -29,6 +29,7 @@ static const char * const ddr_sels[] = { "apll_pfd_sel", "upll", };
static const char * const nic_sels[] = { "firc", "ddr_clk", };
static const char * const periph_plat_sels[] = { "dummy", "nic1_bus_clk", "nic1_clk", "ddr_clk", "apll_pfd2", "apll_pfd1", "apll_pfd0", "upll", };
static const char * const periph_bus_sels[] = { "dummy", "sosc_bus_clk", "mpll", "firc_bus_clk", "rosc", "nic1_bus_clk", "nic1_clk", "spll_bus_clk", };
+static const char * const arm_sels[] = { "divcore", "dummy", "dummy", "hsrun_divcore", };
/* used by sosc/sirc/firc/ddr/spll/apll dividers */
static const struct clk_div_table ulp_div_table[] = {
@@ -102,10 +103,12 @@ static void __init imx7ulp_clk_scg1_init(struct device_node *np)
/* scs/ddr/nic select different clock source requires that clock to be enabled first */
clks[IMX7ULP_CLK_SYS_SEL] = imx_clk_hw_mux2("scs_sel", base + 0x14, 24, 4, scs_sels, ARRAY_SIZE(scs_sels));
+ clks[IMX7ULP_CLK_HSRUN_SYS_SEL] = imx_clk_hw_mux2("hsrun_scs_sel", base + 0x1c, 24, 4, scs_sels, ARRAY_SIZE(scs_sels));
clks[IMX7ULP_CLK_NIC_SEL] = imx_clk_hw_mux2("nic_sel", base + 0x40, 28, 1, nic_sels, ARRAY_SIZE(nic_sels));
clks[IMX7ULP_CLK_DDR_SEL] = imx_clk_hw_mux_flags("ddr_sel", base + 0x30, 24, 1, ddr_sels, ARRAY_SIZE(ddr_sels), CLK_SET_RATE_PARENT | CLK_OPS_PARENT_ENABLE);
- clks[IMX7ULP_CLK_CORE_DIV] = imx_clk_hw_divider_flags("divcore", "scs_sel", base + 0x14, 16, 4, CLK_SET_RATE_PARENT | CLK_IS_CRITICAL);
+ clks[IMX7ULP_CLK_CORE_DIV] = imx_clk_hw_divider_flags("divcore", "scs_sel", base + 0x14, 16, 4, CLK_SET_RATE_PARENT);
+ clks[IMX7ULP_CLK_HSRUN_CORE_DIV] = imx_clk_hw_divider_flags("hsrun_divcore", "hsrun_scs_sel", base + 0x1c, 16, 4, CLK_SET_RATE_PARENT);
clks[IMX7ULP_CLK_DDR_DIV] = imx_clk_divider_gate("ddr_clk", "ddr_sel", CLK_SET_RATE_PARENT | CLK_IS_CRITICAL, base + 0x30, 0, 3,
0, ulp_div_table, &imx_ccm_lock);
@@ -218,3 +221,29 @@ static void __init imx7ulp_clk_pcc3_init(struct device_node *np)
of_clk_add_hw_provider(np, of_clk_hw_onecell_get, clk_data);
}
CLK_OF_DECLARE(imx7ulp_clk_pcc3, "fsl,imx7ulp-pcc3", imx7ulp_clk_pcc3_init);
+
+static void __init imx7ulp_clk_smc1_init(struct device_node *np)
+{
+ struct clk_hw_onecell_data *clk_data;
+ struct clk_hw **clks;
+ void __iomem *base;
+
+ clk_data = kzalloc(sizeof(*clk_data) + sizeof(*clk_data->hws) *
+ IMX7ULP_CLK_SMC1_END, GFP_KERNEL);
+ if (!clk_data)
+ return;
+
+ clk_data->num = IMX7ULP_CLK_SMC1_END;
+ clks = clk_data->hws;
+
+ /* SMC1 */
+ base = of_iomap(np, 0);
+ WARN_ON(!base);
+
+ clks[IMX7ULP_CLK_ARM] = imx_clk_hw_mux_flags("arm", base + 0x10, 8, 2, arm_sels, ARRAY_SIZE(arm_sels), CLK_IS_CRITICAL);
+
+ imx_check_clk_hws(clks, clk_data->num);
+
+ of_clk_add_hw_provider(np, of_clk_hw_onecell_get, clk_data);
+}
+CLK_OF_DECLARE(imx7ulp_clk_smc1, "fsl,imx7ulp-smc1", imx7ulp_clk_smc1_init);
--
2.7.4
next prev parent reply other threads:[~2018-12-07 10:03 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-12-07 10:03 [PATCH 1/3] dt-bindings: clock: imx7ulp: add HSRUN mode related clocks Anson Huang
2018-12-07 10:03 ` Anson Huang [this message]
2018-12-14 22:04 ` [PATCH 2/3] clk: imx: imx7ulp: add arm hsrun mode clocks support Stephen Boyd
2018-12-07 10:03 ` [PATCH 3/3] ARM: dts: imx7ulp: add HSRUN mode clocks Anson Huang
2019-01-10 6:56 ` Shawn Guo
2018-12-14 22:04 ` [PATCH 1/3] dt-bindings: clock: imx7ulp: add HSRUN mode related clocks Stephen Boyd
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1544176659-32022-2-git-send-email-Anson.Huang@nxp.com \
--to=anson.huang@nxp.com \
--cc=aisheng.dong@nxp.com \
--cc=devicetree@vger.kernel.org \
--cc=fabio.estevam@nxp.com \
--cc=kernel@pengutronix.de \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-clk@vger.kernel.org \
--cc=linux-imx@nxp.com \
--cc=linux-kernel@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=mturquette@baylibre.com \
--cc=robh+dt@kernel.org \
--cc=s.hauer@pengutronix.de \
--cc=sboyd@kernel.org \
--cc=shawnguo@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).