linux-kernel.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: <Andrei.Stefanescu@microchip.com>
To: <linus.walleij@linaro.org>, <robh+dt@kernel.org>,
	<gregkh@linuxfoundation.org>, <Nicolas.Ferre@microchip.com>,
	<mark.rutland@arm.com>
Cc: <Ludovic.Desroches@microchip.com>,
	<Cristian.Birsan@microchip.com>,
	<linux-arm-kernel@lists.infradead.org>,
	<linux-gpio@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
	<devicetree@vger.kernel.org>, <Andrei.Stefanescu@microchip.com>
Subject: [PATCH v4 2/2] gpio: add driver for SAMA5D2 PIOBU pins
Date: Wed, 12 Dec 2018 11:57:15 +0000	[thread overview]
Message-ID: <1544615784-29331-3-git-send-email-andrei.stefanescu@microchip.com> (raw)
In-Reply-To: <1544615784-29331-1-git-send-email-andrei.stefanescu@microchip.com>

PIOBU pins do not lose their voltage during Backup/Self-refresh.
This patch adds a simple GPIO controller for them and a
maintainer for the driver.

This driver adds support for using the pins as GPIO
offering the possibility to read/set the voltage.

Signed-off-by: Andrei Stefanescu <andrei.stefanescu@microchip.com>
---
 MAINTAINERS                       |   6 +
 drivers/gpio/Kconfig              |  11 ++
 drivers/gpio/Makefile             |   1 +
 drivers/gpio/gpio-sama5d2-piobu.c | 253 ++++++++++++++++++++++++++++++++++++++
 4 files changed, 271 insertions(+)
 create mode 100644 drivers/gpio/gpio-sama5d2-piobu.c

diff --git a/MAINTAINERS b/MAINTAINERS
index f485597..fadc96d 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -9760,6 +9760,12 @@ M:	Nicolas Ferre <nicolas.ferre@microchip.com>
 S:	Supported
 F:	drivers/power/reset/at91-sama5d2_shdwc.c
 
+MICROCHIP SAMA5D2-COMPATIBLE PIOBU GPIO
+M:	Andrei Stefanescu <andrei.stefanescu@microchip.com>
+L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
+L:	linux-gpio@vger.kernel.org
+F:	drivers/gpio/gpio-sama5d2-piobu.c
+
 MICROCHIP SPI DRIVER
 M:	Nicolas Ferre <nicolas.ferre@microchip.com>
 S:	Supported
diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index 833a1b5..1c41fac 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -429,6 +429,17 @@ config GPIO_REG
 	  A 32-bit single register GPIO fixed in/out implementation.  This
 	  can be used to represent any register as a set of GPIO signals.
 
+config GPIO_SAMA5D2_PIOBU
+	tristate "SAMA5D2 PIOBU GPIO support"
+	depends on MFD_SYSCON
+	select GPIO_SYSCON
+	help
+	  Say yes here to use the PIOBU pins as GPIOs.
+
+	  PIOBU pins on the SAMA5D2 can be used as GPIOs.
+	  The difference from regular GPIOs is that they
+	  maintain their value during backup/self-refresh.
+
 config GPIO_SIOX
 	tristate "SIOX GPIO support"
 	depends on SIOX
diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
index 671c447..f18d345 100644
--- a/drivers/gpio/Makefile
+++ b/drivers/gpio/Makefile
@@ -108,6 +108,7 @@ obj-$(CONFIG_GPIO_RDC321X)	+= gpio-rdc321x.o
 obj-$(CONFIG_GPIO_RCAR)		+= gpio-rcar.o
 obj-$(CONFIG_GPIO_REG)		+= gpio-reg.o
 obj-$(CONFIG_ARCH_SA1100)	+= gpio-sa1100.o
+obj-$(CONFIG_GPIO_SAMA5D2_PIOBU)	+= gpio-sama5d2-piobu.o
 obj-$(CONFIG_GPIO_SCH)		+= gpio-sch.o
 obj-$(CONFIG_GPIO_SCH311X)	+= gpio-sch311x.o
 obj-$(CONFIG_GPIO_SNPS_CREG)	+= gpio-creg-snps.o
diff --git a/drivers/gpio/gpio-sama5d2-piobu.c b/drivers/gpio/gpio-sama5d2-piobu.c
new file mode 100644
index 0000000..03a0006
--- /dev/null
+++ b/drivers/gpio/gpio-sama5d2-piobu.c
@@ -0,0 +1,253 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * SAMA5D2 PIOBU GPIO controller
+ *
+ * Copyright (C) 2018 Microchip Technology Inc. and its subsidiaries
+ *
+ * Author: Andrei Stefanescu <andrei.stefanescu@microchip.com>
+ *
+ */
+#include <linux/bits.h>
+#include <linux/gpio/driver.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+#define PIOBU_NUM 8
+#define PIOBU_REG_SIZE 4
+
+/*
+ * backup mode protection register for tamper detection
+ * normal mode protection register for tamper detection
+ * wakeup signal generation
+ */
+#define PIOBU_BMPR 0x7C
+#define PIOBU_NMPR 0x80
+#define PIOBU_WKPR 0x90
+
+#define PIOBU_BASE 0x18 /* PIOBU offset from SECUMOD base register address. */
+
+#define PIOBU_DET_OFFSET 16
+
+/* In the datasheet this bit is called OUTPUT */
+#define PIOBU_DIRECTION BIT(8)
+#define PIOBU_OUT BIT(8)
+#define PIOBU_IN 0
+
+#define PIOBU_SOD BIT(9)
+#define PIOBU_PDS BIT(10)
+
+#define PIOBU_HIGH BIT(9)
+#define PIOBU_LOW 0
+
+struct sama5d2_piobu {
+	struct gpio_chip chip;
+	struct regmap *regmap;
+};
+
+/**
+ * sama5d2_piobu_setup_pin() - prepares a pin for set_direction call
+ *
+ * Do not consider pin for tamper detection (normal and backup modes)
+ * Do not consider pin as tamper wakeup interrupt source
+ */
+static int sama5d2_piobu_setup_pin(struct gpio_chip *chip, unsigned int pin)
+{
+	int ret;
+	struct sama5d2_piobu *piobu = container_of(chip, struct sama5d2_piobu,
+						   chip);
+	unsigned int mask = BIT(PIOBU_DET_OFFSET + pin);
+
+	ret = regmap_update_bits(piobu->regmap, PIOBU_BMPR, mask, 0);
+	if (ret)
+		return ret;
+
+	ret = regmap_update_bits(piobu->regmap, PIOBU_NMPR, mask, 0);
+	if (ret)
+		return ret;
+
+	return regmap_update_bits(piobu->regmap, PIOBU_WKPR, mask, 0);
+}
+
+/**
+ * sama5d2_piobu_write_value() - writes value & mask at the pin's PIOBU register
+ */
+static int sama5d2_piobu_write_value(struct gpio_chip *chip, unsigned int pin,
+				     unsigned int mask, unsigned int value)
+{
+	int reg;
+	struct sama5d2_piobu *piobu = container_of(chip, struct sama5d2_piobu,
+						   chip);
+
+	reg = PIOBU_BASE + pin * PIOBU_REG_SIZE;
+
+	return regmap_update_bits(piobu->regmap, reg, mask, value);
+}
+
+/**
+ * sama5d2_piobu_read_value() - read the value with masking from the pin's PIOBU
+ *			      register
+ */
+static int sama5d2_piobu_read_value(struct gpio_chip *chip, unsigned int pin,
+				    unsigned int mask)
+{
+	struct sama5d2_piobu *piobu = container_of(chip, struct sama5d2_piobu,
+						   chip);
+	unsigned int val, reg;
+	int ret;
+
+	reg = PIOBU_BASE + pin * PIOBU_REG_SIZE;
+	ret = regmap_read(piobu->regmap, reg, &val);
+	if (ret < 0)
+		return ret;
+
+	return val & mask;
+}
+
+/**
+ * sama5d2_piobu_set_direction() - mark pin as input or output
+ */
+static int sama5d2_piobu_set_direction(struct gpio_chip *chip,
+				       unsigned int direction,
+				       unsigned int pin)
+{
+	return sama5d2_piobu_write_value(chip, pin, PIOBU_DIRECTION, direction);
+}
+
+/**
+ * sama5d2_piobu_get_direction() - gpiochip get_direction
+ */
+static int sama5d2_piobu_get_direction(struct gpio_chip *chip,
+				       unsigned int pin)
+{
+	int ret = sama5d2_piobu_read_value(chip, pin, PIOBU_DIRECTION);
+
+	if (ret < 0)
+		return ret;
+
+	return (ret == PIOBU_IN) ? 1 : 0;
+}
+
+/**
+ * sama5d2_piobu_direction_input() - gpiochip direction_input
+ */
+static int sama5d2_piobu_direction_input(struct gpio_chip *chip,
+					 unsigned int pin)
+{
+	return sama5d2_piobu_set_direction(chip, PIOBU_IN, pin);
+}
+
+/**
+ * sama5d2_piobu_direction_output() - gpiochip direction_output
+ */
+static int sama5d2_piobu_direction_output(struct gpio_chip *chip,
+					  unsigned int pin, int value)
+{
+	return sama5d2_piobu_set_direction(chip, PIOBU_OUT, pin);
+}
+
+/**
+ * sama5d2_piobu_get() - gpiochip get
+ */
+static int sama5d2_piobu_get(struct gpio_chip *chip, unsigned int pin)
+{
+	/* if pin is input, read value from PDS else read from SOD */
+	int ret = sama5d2_piobu_get_direction(chip, pin);
+
+	if (ret == 1)
+		ret = sama5d2_piobu_read_value(chip, pin, PIOBU_PDS);
+	else if (!ret)
+		ret = sama5d2_piobu_read_value(chip, pin, PIOBU_SOD);
+
+	if (ret < 0)
+		return ret;
+
+	return !!ret;
+}
+
+/**
+ * sama5d2_piobu_set() - gpiochip set
+ */
+static void sama5d2_piobu_set(struct gpio_chip *chip, unsigned int pin,
+			      int value)
+{
+	if (!value)
+		value = PIOBU_LOW;
+	else
+		value = PIOBU_HIGH;
+
+	sama5d2_piobu_write_value(chip, pin, PIOBU_SOD, value);
+}
+
+static int sama5d2_piobu_probe(struct platform_device *pdev)
+{
+	struct sama5d2_piobu *piobu;
+	int ret, i;
+
+	piobu = devm_kzalloc(&pdev->dev, sizeof(*piobu), GFP_KERNEL);
+	if (!piobu)
+		return -ENOMEM;
+
+	platform_set_drvdata(pdev, piobu);
+	piobu->chip.label = pdev->name;
+	piobu->chip.parent = &pdev->dev;
+	piobu->chip.of_node = pdev->dev.of_node;
+	piobu->chip.owner = THIS_MODULE,
+	piobu->chip.get_direction = sama5d2_piobu_get_direction,
+	piobu->chip.direction_input = sama5d2_piobu_direction_input,
+	piobu->chip.direction_output = sama5d2_piobu_direction_output,
+	piobu->chip.get = sama5d2_piobu_get,
+	piobu->chip.set = sama5d2_piobu_set,
+	piobu->chip.base = -1,
+	piobu->chip.ngpio = PIOBU_NUM,
+	piobu->chip.can_sleep = 0,
+
+	piobu->regmap = syscon_node_to_regmap(pdev->dev.of_node);
+	if (IS_ERR(piobu->regmap)) {
+		dev_err(&pdev->dev, "Failed to get syscon regmap %ld\n",
+			PTR_ERR(piobu->regmap));
+		return PTR_ERR(piobu->regmap);
+	}
+
+	ret = devm_gpiochip_add_data(&pdev->dev, &piobu->chip, piobu);
+	if (ret) {
+		dev_err(&pdev->dev, "Failed to add gpiochip %d\n", ret);
+		return ret;
+	}
+
+	for (i = 0; i < PIOBU_NUM; ++i) {
+		ret = sama5d2_piobu_setup_pin(&piobu->chip, i);
+		if (ret) {
+			dev_err(&pdev->dev, "Failed to setup pin: %d %d\n",
+				i, ret);
+			return ret;
+		}
+	}
+
+	return 0;
+}
+
+static const struct of_device_id sama5d2_piobu_ids[] = {
+	{ .compatible = "atmel,sama5d2-secumod" },
+	{},
+};
+MODULE_DEVICE_TABLE(of, sama5d2_piobu_ids);
+
+static struct platform_driver sama5d2_piobu_driver = {
+	.driver = {
+		.name		= "sama5d2-piobu",
+		.of_match_table	= of_match_ptr(sama5d2_piobu_ids)
+	},
+	.probe = sama5d2_piobu_probe,
+};
+
+module_platform_driver(sama5d2_piobu_driver);
+
+MODULE_VERSION("1.0");
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("SAMA5D2 PIOBU controller driver");
+MODULE_AUTHOR("Andrei Stefanescu <andrei.stefanescu@microchip.com>");
-- 
2.7.4


  parent reply	other threads:[~2018-12-12 11:57 UTC|newest]

Thread overview: 6+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2018-12-12 11:56 [PATCH v4 0/2] add SAMA5D2 PIOBU GPIO driver Andrei.Stefanescu
2018-12-12 11:57 ` [PATCH v4 1/2] dt-bindings: arm: atmel: describe SECUMOD usage as a GPIO controller Andrei.Stefanescu
2018-12-17 21:47   ` Rob Herring
2018-12-21  9:55   ` Linus Walleij
2018-12-12 11:57 ` Andrei.Stefanescu [this message]
2018-12-21  9:57   ` [PATCH v4 2/2] gpio: add driver for SAMA5D2 PIOBU pins Linus Walleij

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1544615784-29331-3-git-send-email-andrei.stefanescu@microchip.com \
    --to=andrei.stefanescu@microchip.com \
    --cc=Cristian.Birsan@microchip.com \
    --cc=Ludovic.Desroches@microchip.com \
    --cc=Nicolas.Ferre@microchip.com \
    --cc=devicetree@vger.kernel.org \
    --cc=gregkh@linuxfoundation.org \
    --cc=linus.walleij@linaro.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-gpio@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=mark.rutland@arm.com \
    --cc=robh+dt@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).