From: Brian Masney <masneyb@onstation.org>
To: linus.walleij@linaro.org, sboyd@kernel.org,
bjorn.andersson@linaro.org, andy.gross@linaro.org,
lee.jones@linaro.org
Cc: marc.zyngier@arm.com, shawnguo@kernel.org, dianders@chromium.org,
linux-gpio@vger.kernel.org, nicolas.dechesne@linaro.org,
niklas.cassel@linaro.org, david.brown@linaro.org,
robh+dt@kernel.org, mark.rutland@arm.com,
thierry.reding@gmail.com, linux-arm-msm@vger.kernel.org,
linux-kernel@vger.kernel.org, devicetree@vger.kernel.org
Subject: [PATCH v2 5/5] ARM: dts: qcom: msm8974: add interrupt controller properties
Date: Sun, 6 Jan 2019 21:11:45 -0500 [thread overview]
Message-ID: <20190107021145.6370-6-masneyb@onstation.org> (raw)
In-Reply-To: <20190107021145.6370-1-masneyb@onstation.org>
Add interrupt controller properties now that spmi-gpio is a proper
hierarchical IRQ chip. The interrupts property is no longer needed so
remove it.
Signed-off-by: Brian Masney <masneyb@onstation.org>
---
Changes since v1:
- Interrupts are now two cells instead of four cells.
- Drop unnecessary interrupts property.
arch/arm/boot/dts/qcom-pm8941.dtsi | 39 +++---------------------------
1 file changed, 3 insertions(+), 36 deletions(-)
diff --git a/arch/arm/boot/dts/qcom-pm8941.dtsi b/arch/arm/boot/dts/qcom-pm8941.dtsi
index 2515c5c217ac..16e6b4272d16 100644
--- a/arch/arm/boot/dts/qcom-pm8941.dtsi
+++ b/arch/arm/boot/dts/qcom-pm8941.dtsi
@@ -64,42 +64,9 @@
reg = <0xc000>;
gpio-controller;
#gpio-cells = <2>;
- interrupts = <0 0xc0 0 IRQ_TYPE_NONE>,
- <0 0xc1 0 IRQ_TYPE_NONE>,
- <0 0xc2 0 IRQ_TYPE_NONE>,
- <0 0xc3 0 IRQ_TYPE_NONE>,
- <0 0xc4 0 IRQ_TYPE_NONE>,
- <0 0xc5 0 IRQ_TYPE_NONE>,
- <0 0xc6 0 IRQ_TYPE_NONE>,
- <0 0xc7 0 IRQ_TYPE_NONE>,
- <0 0xc8 0 IRQ_TYPE_NONE>,
- <0 0xc9 0 IRQ_TYPE_NONE>,
- <0 0xca 0 IRQ_TYPE_NONE>,
- <0 0xcb 0 IRQ_TYPE_NONE>,
- <0 0xcc 0 IRQ_TYPE_NONE>,
- <0 0xcd 0 IRQ_TYPE_NONE>,
- <0 0xce 0 IRQ_TYPE_NONE>,
- <0 0xcf 0 IRQ_TYPE_NONE>,
- <0 0xd0 0 IRQ_TYPE_NONE>,
- <0 0xd1 0 IRQ_TYPE_NONE>,
- <0 0xd2 0 IRQ_TYPE_NONE>,
- <0 0xd3 0 IRQ_TYPE_NONE>,
- <0 0xd4 0 IRQ_TYPE_NONE>,
- <0 0xd5 0 IRQ_TYPE_NONE>,
- <0 0xd6 0 IRQ_TYPE_NONE>,
- <0 0xd7 0 IRQ_TYPE_NONE>,
- <0 0xd8 0 IRQ_TYPE_NONE>,
- <0 0xd9 0 IRQ_TYPE_NONE>,
- <0 0xda 0 IRQ_TYPE_NONE>,
- <0 0xdb 0 IRQ_TYPE_NONE>,
- <0 0xdc 0 IRQ_TYPE_NONE>,
- <0 0xdd 0 IRQ_TYPE_NONE>,
- <0 0xde 0 IRQ_TYPE_NONE>,
- <0 0xdf 0 IRQ_TYPE_NONE>,
- <0 0xe0 0 IRQ_TYPE_NONE>,
- <0 0xe1 0 IRQ_TYPE_NONE>,
- <0 0xe2 0 IRQ_TYPE_NONE>,
- <0 0xe3 0 IRQ_TYPE_NONE>;
+ interrupt-parent = <&spmi_bus>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
boost_bypass_n_pin: boost-bypass {
pins = "gpio21";
--
2.17.2
next prev parent reply other threads:[~2019-01-07 2:12 UTC|newest]
Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-01-07 2:11 [PATCH v2 0/5] qcom: spmi: add support for hierarchical IRQ chip Brian Masney
2019-01-07 2:11 ` [PATCH v2 1/5] spmi: pmic-arb: hardcode IRQ counts Brian Masney
2019-01-07 7:13 ` kbuild test robot
2019-01-07 10:47 ` Linus Walleij
2019-01-07 21:26 ` Stephen Boyd
2019-01-07 2:11 ` [PATCH v2 2/5] mfd: qcom-spmi-pmic: use devm_mfd_add_devices instead of devm_of_platform_populate Brian Masney
2019-01-07 10:53 ` Linus Walleij
2019-01-07 11:30 ` Brian Masney
2019-01-07 21:41 ` Stephen Boyd
2019-01-08 10:32 ` Brian Masney
2019-01-07 2:11 ` [PATCH v2 3/5] spmi: pmic-arb: convert to v2 irq interfaces to support hierarchical IRQ chips Brian Masney
2019-01-07 2:11 ` [PATCH v2 4/5] qcom: spmi-gpio: add support for hierarchical IRQ chip Brian Masney
2019-01-07 21:55 ` Stephen Boyd
2019-01-08 10:35 ` Brian Masney
2019-01-07 2:11 ` Brian Masney [this message]
2019-01-07 23:51 ` [PATCH v2 5/5] ARM: dts: qcom: msm8974: add interrupt controller properties Stephen Boyd
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190107021145.6370-6-masneyb@onstation.org \
--to=masneyb@onstation.org \
--cc=andy.gross@linaro.org \
--cc=bjorn.andersson@linaro.org \
--cc=david.brown@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=dianders@chromium.org \
--cc=lee.jones@linaro.org \
--cc=linus.walleij@linaro.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-gpio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=marc.zyngier@arm.com \
--cc=mark.rutland@arm.com \
--cc=nicolas.dechesne@linaro.org \
--cc=niklas.cassel@linaro.org \
--cc=robh+dt@kernel.org \
--cc=sboyd@kernel.org \
--cc=shawnguo@kernel.org \
--cc=thierry.reding@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).