From: Erin Lo <erin.lo@mediatek.com>
To: Matthias Brugger <matthias.bgg@gmail.com>,
Rob Herring <robh+dt@kernel.org>,
Mark Rutland <mark.rutland@arm.com>,
Thomas Gleixner <tglx@linutronix.de>,
Jason Cooper <jason@lakedaemon.net>,
Marc Zyngier <marc.zyngier@arm.com>,
Greg Kroah-Hartman <gregkh@linuxfoundation.org>,
Stephen Boyd <sboyd@codeaurora.org>
Cc: <devicetree@vger.kernel.org>,
srv_heupstream <srv_heupstream@mediatek.com>,
<linux-kernel@vger.kernel.org>, <linux-serial@vger.kernel.org>,
<linux-mediatek@lists.infradead.org>,
<linux-arm-kernel@lists.infradead.org>,
<yingjoe.chen@mediatek.com>, <erin.lo@mediatek.com>,
<mars.cheng@mediatek.com>, <eddie.huang@mediatek.com>,
<linux-clk@vger.kernel.org>,
Zhiyong Tao <zhiyong.tao@mediatek.com>
Subject: [PATCH v6 5/6] dt-bindings: pinctrl: mt8183: add binding document
Date: Thu, 24 Jan 2019 16:07:19 +0800 [thread overview]
Message-ID: <1548317240-44682-6-git-send-email-erin.lo@mediatek.com> (raw)
In-Reply-To: <1548317240-44682-1-git-send-email-erin.lo@mediatek.com>
From: Zhiyong Tao <zhiyong.tao@mediatek.com>
The commit adds mt8183 compatible node in binding document.
Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Signed-off-by: Erin Lo <erin.lo@mediatek.com>
---
.../devicetree/bindings/pinctrl/pinctrl-mt8183.txt | 115 +++++++++++++++++++++
1 file changed, 115 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pinctrl/pinctrl-mt8183.txt
diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8183.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8183.txt
new file mode 100644
index 0000000..364e673
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8183.txt
@@ -0,0 +1,115 @@
+* Mediatek MT8183 Pin Controller
+
+The Mediatek's Pin controller is used to control SoC pins.
+
+Required properties:
+- compatible: value should be one of the following.
+ "mediatek,mt8183-pinctrl", compatible with mt8183 pinctrl.
+- gpio-controller : Marks the device node as a gpio controller.
+- #gpio-cells: number of cells in GPIO specifier. Since the generic GPIO
+ binding is used, the amount of cells must be specified as 2. See the below
+ mentioned gpio binding representation for description of particular cells.
+- gpio-ranges : gpio valid number range.
+- reg: physicall address base for gpio base registers. There are nine
+ physicall address base in mt8183. They are 0x10005000, 0x11F20000,
+ 0x11E80000, 0x11E70000, 0x11E90000, 0x11D30000, 0x11D20000, 0x11C50000,
+ 0x11F30000.
+
+ Eg: <&pio 6 0>
+ <[phandle of the gpio controller node]
+ [line number within the gpio controller]
+ [flags]>
+
+ Values for gpio specifier:
+ - Line number: is a value between 0 to 202.
+ - Flags: bit field of flags, as defined in <dt-bindings/gpio/gpio.h>.
+ Only the following flags are supported:
+ 0 - GPIO_ACTIVE_HIGH
+ 1 - GPIO_ACTIVE_LOW
+
+Optional properties:
+- reg-names: gpio base register names. There are nine gpio base register
+ names in mt8183. They are "iocfg0", "iocfg1", "iocfg2", "iocfg3", "iocfg4",
+ "iocfg5", "iocfg6", "iocfg7", "iocfg8".
+- interrupt-controller: Marks the device node as an interrupt controller
+- #interrupt-cells: Should be two.
+- interrupts : The interrupt outputs from the controller.
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices.
+
+Subnode format
+A pinctrl node should contain at least one subnodes representing the
+pinctrl groups available on the machine. Each subnode will list the
+pins it needs, and how they should be configured, with regard to muxer
+configuration, pullups, drive strength, input enable/disable and input schmitt.
+
+ node {
+ pinmux = <PIN_NUMBER_PINMUX>;
+ GENERIC_PINCONFIG;
+ };
+
+Required properties:
+- pinmux: integer array, represents gpio pin number and mux setting.
+ Supported pin number and mux varies for different SoCs, and are defined
+ as macros in boot/dts/<soc>-pinfunc.h directly.
+
+Optional properties:
+- GENERIC_PINCONFIG: is the generic pinconfig options to use, bias-disable,
+ bias-pull-down, bias-pull-up, input-enable, input-disable, output-low, output-high,
+ input-schmitt-enable, input-schmitt-disable and drive-strength are valid.
+
+ Some special pins have extra pull up strength, there are R0 and R1 pull-up
+ resistors available, but for user, it's only need to set R1R0 as 00, 01, 10 or 11.
+ So when config mediatek,pull-up-adv or mediatek,pull-down-adv,
+ it support arguments for those special pins.
+
+ When config drive-strength, it can support some arguments, such as
+ MTK_DRIVE_4mA, MTK_DRIVE_6mA, etc. See dt-bindings/pinctrl/mt65xx.h.
+
+Examples:
+
+#include "mt8183-pinfunc.h"
+
+...
+{
+ pio: pinctrl@10005000 {
+ compatible = "mediatek,mt8183-pinctrl";
+ reg = <0 0x10005000 0 0x1000>,
+ <0 0x11F20000 0 0x1000>,
+ <0 0x11E80000 0 0x1000>,
+ <0 0x11E70000 0 0x1000>,
+ <0 0x11E90000 0 0x1000>,
+ <0 0x11D30000 0 0x1000>,
+ <0 0x11D20000 0 0x1000>,
+ <0 0x11C50000 0 0x1000>,
+ <0 0x11F30000 0 0x1000>;
+ reg-names = "iocfg0", "iocfg1", "iocfg2",
+ "iocfg3", "iocfg4", "iocfg5",
+ "iocfg6", "iocfg7", "iocfg8";
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&pio 0 0 192>;
+ interrupt-controller;
+ interrupts = <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-parent = <&gic>;
+ #interrupt-cells = <2>;
+
+ i2c0_pins_a: i2c0 {
+ pins1 {
+ pinmux = <PINMUX_GPIO48__FUNC_SCL5>,
+ <PINMUX_GPIO49__FUNC_SDA5>;
+ mediatek,pull-up-adv = <11>;
+ };
+ };
+
+ i2c1_pins_a: i2c1 {
+ pins {
+ pinmux = <PINMUX_GPIO50__FUNC_SCL3>,
+ <PINMUX_GPIO51__FUNC_SDA3>;
+ mediatek,pull-down-adv = <10>;
+ };
+ };
+ ...
+ };
+};
--
1.9.1
next prev parent reply other threads:[~2019-01-24 8:15 UTC|newest]
Thread overview: 31+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-01-24 8:07 [PATCH v6 0/6] Add basic and clock support for Mediatek MT8183 SoC Erin Lo
2019-01-24 8:07 ` [PATCH v6 1/6] irqchip/mtk-sysirq: support 4 interrupt parameters for sysirq Erin Lo
2019-02-07 15:20 ` Matthias Brugger
2019-02-07 15:47 ` Marc Zyngier
2019-02-07 15:52 ` Marc Zyngier
2019-02-11 6:35 ` Seiya Wang
2019-02-11 8:50 ` Marc Zyngier
2019-02-11 13:01 ` Seiya Wang
2019-01-24 8:07 ` [PATCH v6 2/6] dt-bindings: arm: Add bindings for Mediatek MT8183 SoC Platform Erin Lo
2019-02-07 15:15 ` Matthias Brugger
2019-01-24 8:07 ` [PATCH v6 3/6] dt-bindings: mtk-sysirq: Add compatible for Mediatek MT8183 Erin Lo
2019-01-24 8:07 ` [PATCH v6 4/6] dt-bindings: serial: " Erin Lo
2019-01-24 8:07 ` Erin Lo [this message]
2019-01-30 16:17 ` [PATCH v6 5/6] dt-bindings: pinctrl: mt8183: add binding document Rob Herring
2019-01-31 8:30 ` Zhiyong Tao
2019-02-07 15:28 ` Matthias Brugger
2019-02-14 3:29 ` Erin Lo
2019-01-24 8:07 ` [PATCH v6 6/6] arm64: dts: Add Mediatek SoC MT8183 and evaluation board dts and Makefile Erin Lo
2019-01-30 16:22 ` Rob Herring
2019-01-31 2:34 ` Erin Lo
2019-01-31 21:10 ` Rob Herring
[not found] ` <1548992018.11367.8.camel@mtksdaap41>
2019-02-01 5:11 ` Erin Lo
2019-02-07 15:08 ` Matthias Brugger
2019-02-09 7:37 ` Erin Lo
2019-02-07 15:30 ` Matthias Brugger
2019-02-13 9:03 ` Erin Lo
2019-02-13 14:54 ` Matthias Brugger
2019-02-14 5:27 ` Erin Lo
2019-02-14 9:01 ` Matthias Brugger
2019-02-14 10:14 ` Erin Lo
2019-02-14 10:15 ` Erin Lo
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1548317240-44682-6-git-send-email-erin.lo@mediatek.com \
--to=erin.lo@mediatek.com \
--cc=devicetree@vger.kernel.org \
--cc=eddie.huang@mediatek.com \
--cc=gregkh@linuxfoundation.org \
--cc=jason@lakedaemon.net \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-clk@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mediatek@lists.infradead.org \
--cc=linux-serial@vger.kernel.org \
--cc=marc.zyngier@arm.com \
--cc=mark.rutland@arm.com \
--cc=mars.cheng@mediatek.com \
--cc=matthias.bgg@gmail.com \
--cc=robh+dt@kernel.org \
--cc=sboyd@codeaurora.org \
--cc=srv_heupstream@mediatek.com \
--cc=tglx@linutronix.de \
--cc=yingjoe.chen@mediatek.com \
--cc=zhiyong.tao@mediatek.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).