From: Sugaya Taichi <sugaya.taichi@socionext.com>
To: devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
linux-arm-kernel@lists.infradead.org, soc@kernel.org
Cc: Rob Herring <robh+dt@kernel.org>,
Mark Rutland <mark.rutland@arm.com>,
Takao Orito <orito.takao@socionext.com>,
Kazuhiro Kasai <kasai.kazuhiro@socionext.com>,
Shinji Kanematsu <kanematsu.shinji@socionext.com>,
Jassi Brar <jaswinder.singh@linaro.org>,
Masami Hiramatsu <masami.hiramatsu@linaro.org>,
Sugaya Taichi <sugaya.taichi@socionext.com>
Subject: [PATCH v3 8/9] ARM: dts: milbeaut: Add device tree set for the Milbeaut M10V board
Date: Wed, 20 Feb 2019 16:44:53 +0900 [thread overview]
Message-ID: <1550648693-11382-1-git-send-email-sugaya.taichi@socionext.com> (raw)
Add devicetree for Milbeaut M10V SoC and M10V Evaluation board.
Signed-off-by: Sugaya Taichi <sugaya.taichi@socionext.com>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/milbeaut-m10v-evb.dts | 32 +++++++++++
arch/arm/boot/dts/milbeaut-m10v.dtsi | 95 +++++++++++++++++++++++++++++++++
3 files changed, 128 insertions(+)
create mode 100644 arch/arm/boot/dts/milbeaut-m10v-evb.dts
create mode 100644 arch/arm/boot/dts/milbeaut-m10v.dtsi
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index bd40148..f697d87 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1233,6 +1233,7 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += \
mt7623n-bananapi-bpi-r2.dtb \
mt8127-moose.dtb \
mt8135-evbp1.dtb
+dtb-$(CONFIG_ARCH_MILBEAUT) += milbeaut-m10v-evb.dtb
dtb-$(CONFIG_ARCH_ZX) += zx296702-ad1.dtb
dtb-$(CONFIG_ARCH_ASPEED) += \
aspeed-ast2500-evb.dtb \
diff --git a/arch/arm/boot/dts/milbeaut-m10v-evb.dts b/arch/arm/boot/dts/milbeaut-m10v-evb.dts
new file mode 100644
index 0000000..614f60c
--- /dev/null
+++ b/arch/arm/boot/dts/milbeaut-m10v-evb.dts
@@ -0,0 +1,32 @@
+// SPDX-License-Identifier: GPL-2.0
+/* Socionext Milbeaut M10V Evaluation Board */
+/dts-v1/;
+#include "milbeaut-m10v.dtsi"
+
+/ {
+ model = "Socionext M10V EVB";
+ compatible = "socionext,milbeaut-m10v-evb", "socionext,sc2000a";
+
+ aliases {
+ serial0 = &uart1;
+ };
+
+ chosen {
+ bootargs = "rootwait earlycon";
+ stdout-path = "serial0:115200n8";
+ };
+
+ clocks {
+ uclk40xi: uclk40xi {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <40000000>;
+ };
+ };
+
+ memory@40000000 {
+ device_type = "memory";
+ reg = <0x40000000 0x80000000>;
+ };
+
+};
diff --git a/arch/arm/boot/dts/milbeaut-m10v.dtsi b/arch/arm/boot/dts/milbeaut-m10v.dtsi
new file mode 100644
index 0000000..aa7c6ca
--- /dev/null
+++ b/arch/arm/boot/dts/milbeaut-m10v.dtsi
@@ -0,0 +1,95 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+ compatible = "socionext,sc2000a";
+ interrupt-parent = <&gic>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ enable-method = "socionext,milbeaut-m10v-smp";
+ cpu@f00 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a7";
+ reg = <0xf00>;
+ };
+ cpu@f01 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a7";
+ reg = <0xf01>;
+ };
+ cpu@f02 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a7";
+ reg = <0xf02>;
+ };
+ cpu@f03 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a7";
+ reg = <0xf03>;
+ };
+ };
+
+ timer { /* The Generic Timer */
+ compatible = "arm,armv7-timer";
+ interrupts = <GIC_PPI 13
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+ <GIC_PPI 14
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+ <GIC_PPI 11
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+ <GIC_PPI 10
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+ clock-frequency = <40000000>;
+ always-on;
+ };
+
+ soc {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ interrupt-parent = <&gic>;
+
+ gic: interrupt-controller@1d000000 {
+ compatible = "arm,cortex-a7-gic";
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ reg = <0x1d001000 0x1000>,
+ <0x1d002000 0x1000>; /* CPU I/f base and size */
+ };
+
+ timer@1e000050 { /* 32-bit Reload Timers */
+ compatible = "socionext,milbeaut-timer";
+ reg = <0x1e000050 0x20>;
+ interrupts = <0 91 4>;
+ };
+
+ uart1: serial@1e700010 { /* PE4, PE5 */
+ /* Enable this as ttyUSI0 */
+ compatible = "socionext,milbeaut-usio-uart";
+ reg = <0x1e700010 0x10>;
+ interrupts = <0 141 0x4>, <0 149 0x4>;
+ interrupt-names = "rx", "tx";
+ };
+
+ };
+
+ sram@0 {
+ compatible = "mmio-sram";
+ reg = <0x0 0x10000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x0 0x10000>;
+ smp-sram@f100 {
+ compatible = "socionext,milbeaut-smp-sram";
+ reg = <0xf100 0x20>;
+ };
+ };
+};
--
1.9.1
reply other threads:[~2019-02-20 7:44 UTC|newest]
Thread overview: [no followups] expand[flat|nested] mbox.gz Atom feed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1550648693-11382-1-git-send-email-sugaya.taichi@socionext.com \
--to=sugaya.taichi@socionext.com \
--cc=devicetree@vger.kernel.org \
--cc=jaswinder.singh@linaro.org \
--cc=kanematsu.shinji@socionext.com \
--cc=kasai.kazuhiro@socionext.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=masami.hiramatsu@linaro.org \
--cc=orito.takao@socionext.com \
--cc=robh+dt@kernel.org \
--cc=soc@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).