From: Peng Ma <peng.ma@nxp.com>
To: axboe@kernel.dk, robh+dt@kernel.org, mark.rutland@arm.com,
shawnguo@kernel.org, leoyang.li@nxp.com, andy.tang@nxp.com
Cc: linux-ide@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org,
linux-arm-kernel@lists.infradead.org, yousaf.kaukab@suse.com,
Peng Ma <peng.ma@nxp.com>
Subject: [v6 3/3] ahci: qoriq: add lx2160 platforms support
Date: Wed, 20 Feb 2019 08:56:07 +0000 [thread overview]
Message-ID: <20190220085607.31582-3-peng.ma@nxp.com> (raw)
In-Reply-To: <20190220085607.31582-1-peng.ma@nxp.com>
Lx2160a is a new introduced soc which supports ATA3.0
Signed-off-by: Peng Ma <peng.ma@nxp.com>
---
changed for V6:
- Add ecc_initialized to ensure set sata bit once of
ECC error register
- Recovery AHCI_LS2088A platform
drivers/ata/ahci_qoriq.c | 52 +++++++++++++++++++++++++++++++---------------
1 files changed, 35 insertions(+), 17 deletions(-)
diff --git a/drivers/ata/ahci_qoriq.c b/drivers/ata/ahci_qoriq.c
index ce59253..08dbb86 100644
--- a/drivers/ata/ahci_qoriq.c
+++ b/drivers/ata/ahci_qoriq.c
@@ -58,6 +58,7 @@ enum ahci_qoriq_type {
AHCI_LS1046A,
AHCI_LS1088A,
AHCI_LS2088A,
+ AHCI_LX2160A,
};
struct ahci_qoriq_priv {
@@ -67,6 +68,8 @@ struct ahci_qoriq_priv {
bool is_dmacoherent;
};
+static bool ecc_initialized;
+
static const struct of_device_id ahci_qoriq_of_match[] = {
{ .compatible = "fsl,ls1021a-ahci", .data = (void *)AHCI_LS1021A},
{ .compatible = "fsl,ls1043a-ahci", .data = (void *)AHCI_LS1043A},
@@ -74,6 +77,7 @@ struct ahci_qoriq_priv {
{ .compatible = "fsl,ls1046a-ahci", .data = (void *)AHCI_LS1046A},
{ .compatible = "fsl,ls1088a-ahci", .data = (void *)AHCI_LS1088A},
{ .compatible = "fsl,ls2088a-ahci", .data = (void *)AHCI_LS2088A},
+ { .compatible = "fsl,lx2160a-ahci", .data = (void *)AHCI_LX2160A},
{},
};
MODULE_DEVICE_TABLE(of, ahci_qoriq_of_match);
@@ -165,9 +169,10 @@ static int ahci_qoriq_phy_init(struct ahci_host_priv *hpriv)
switch (qpriv->type) {
case AHCI_LS1021A:
- if (!qpriv->ecc_addr)
+ if (!(qpriv->ecc_addr || ecc_initialized))
return -EINVAL;
- writel(SATA_ECC_DISABLE, qpriv->ecc_addr);
+ else if (qpriv->ecc_addr && !ecc_initialized)
+ writel(SATA_ECC_DISABLE, qpriv->ecc_addr);
writel(AHCI_PORT_PHY_1_CFG, reg_base + PORT_PHY1);
writel(LS1021A_PORT_PHY2, reg_base + PORT_PHY2);
writel(LS1021A_PORT_PHY3, reg_base + PORT_PHY3);
@@ -180,10 +185,12 @@ static int ahci_qoriq_phy_init(struct ahci_host_priv *hpriv)
break;
case AHCI_LS1043A:
- if (!qpriv->ecc_addr)
+ if (!(qpriv->ecc_addr || ecc_initialized))
return -EINVAL;
- writel(readl(qpriv->ecc_addr) | ECC_DIS_ARMV8_CH2,
- qpriv->ecc_addr);
+ else if (qpriv->ecc_addr && !ecc_initialized)
+ writel(readl(qpriv->ecc_addr) |
+ ECC_DIS_ARMV8_CH2,
+ qpriv->ecc_addr);
writel(AHCI_PORT_PHY_1_CFG, reg_base + PORT_PHY1);
writel(AHCI_PORT_PHY2_CFG, reg_base + PORT_PHY2);
writel(AHCI_PORT_PHY3_CFG, reg_base + PORT_PHY3);
@@ -202,10 +209,12 @@ static int ahci_qoriq_phy_init(struct ahci_host_priv *hpriv)
break;
case AHCI_LS1046A:
- if (!qpriv->ecc_addr)
+ if (!(qpriv->ecc_addr || ecc_initialized))
return -EINVAL;
- writel(readl(qpriv->ecc_addr) | ECC_DIS_ARMV8_CH2,
- qpriv->ecc_addr);
+ else if (qpriv->ecc_addr && !ecc_initialized)
+ writel(readl(qpriv->ecc_addr) |
+ ECC_DIS_ARMV8_CH2,
+ qpriv->ecc_addr);
writel(AHCI_PORT_PHY_1_CFG, reg_base + PORT_PHY1);
writel(AHCI_PORT_PHY2_CFG, reg_base + PORT_PHY2);
writel(AHCI_PORT_PHY3_CFG, reg_base + PORT_PHY3);
@@ -215,10 +224,13 @@ static int ahci_qoriq_phy_init(struct ahci_host_priv *hpriv)
break;
case AHCI_LS1088A:
- if (!qpriv->ecc_addr)
+ case AHCI_LX2160A:
+ if (!(qpriv->ecc_addr || ecc_initialized))
return -EINVAL;
- writel(readl(qpriv->ecc_addr) | ECC_DIS_LS1088A,
- qpriv->ecc_addr);
+ else if (qpriv->ecc_addr && !ecc_initialized)
+ writel(readl(qpriv->ecc_addr) |
+ ECC_DIS_LS1088A,
+ qpriv->ecc_addr);
writel(AHCI_PORT_PHY_1_CFG, reg_base + PORT_PHY1);
writel(AHCI_PORT_PHY2_CFG, reg_base + PORT_PHY2);
writel(AHCI_PORT_PHY3_CFG, reg_base + PORT_PHY3);
@@ -237,6 +249,7 @@ static int ahci_qoriq_phy_init(struct ahci_host_priv *hpriv)
break;
}
+ ecc_initialized = true;
return 0;
}
@@ -264,13 +277,18 @@ static int ahci_qoriq_probe(struct platform_device *pdev)
qoriq_priv->type = (enum ahci_qoriq_type)of_id->data;
- res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
- "sata-ecc");
- if (res) {
- qoriq_priv->ecc_addr = devm_ioremap_resource(dev, res);
- if (IS_ERR(qoriq_priv->ecc_addr))
- return PTR_ERR(qoriq_priv->ecc_addr);
+ if (unlikely(!ecc_initialized)) {
+ res = platform_get_resource_byname(pdev,
+ IORESOURCE_MEM,
+ "sata-ecc");
+ if (res) {
+ qoriq_priv->ecc_addr =
+ devm_ioremap_resource(dev, res);
+ if (IS_ERR(qoriq_priv->ecc_addr))
+ return PTR_ERR(qoriq_priv->ecc_addr);
+ }
}
+
qoriq_priv->is_dmacoherent = of_dma_is_coherent(np);
rc = ahci_platform_enable_resources(hpriv);
--
1.7.1
next prev parent reply other threads:[~2019-02-20 9:02 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-02-20 8:56 [v6 1/3] dt-bindings: ahci-fsl-qoriq: add lx2160a chip name to the list Peng Ma
2019-02-20 8:56 ` [v6 2/3] arm64: dts: lx2160a: add sata node support Peng Ma
2019-02-20 8:56 ` Peng Ma [this message]
2019-02-22 14:39 ` [v6 1/3] dt-bindings: ahci-fsl-qoriq: add lx2160a chip name to the list Rob Herring
2019-03-11 6:56 ` Peng Ma
2019-03-11 21:39 ` Rob Herring
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190220085607.31582-3-peng.ma@nxp.com \
--to=peng.ma@nxp.com \
--cc=andy.tang@nxp.com \
--cc=axboe@kernel.dk \
--cc=devicetree@vger.kernel.org \
--cc=leoyang.li@nxp.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-ide@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=robh+dt@kernel.org \
--cc=shawnguo@kernel.org \
--cc=yousaf.kaukab@suse.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).