From: Mason Yang <masonccyang@mxic.com.tw>
To: broonie@kernel.org, marek.vasut@gmail.com,
linux-kernel@vger.kernel.org, linux-spi@vger.kernel.org,
bbrezillon@kernel.org, dwmw2@infradead.org, lee.jones@linaro.org,
robh+dt@kernel.org, mark.rutland@arm.com,
computersforpeace@gmal.com, paul.burton@mips.com,
stefan@agner.ch, christophe.kerello@st.com,
liang.yang@amlogic.com, geert@linux-m68k.org,
devicetree@vger.kernel.org, marcel.ziswiler@toradex.com,
linux-mtd@lists.infradead.org, richard@nod.at,
miquel.raynal@bootlin.com
Cc: juliensu@mxic.com.tw, zhengxunli@mxic.com.tw,
Mason Yang <masonccyang@mxic.com.tw>
Subject: [PATCH v2 1/4] mfd: Add Macronix MX25F0A MFD controller driver
Date: Tue, 9 Apr 2019 10:29:57 +0800 [thread overview]
Message-ID: <1554777000-10542-2-git-send-email-masonccyang@mxic.com.tw> (raw)
In-Reply-To: <1554777000-10542-1-git-send-email-masonccyang@mxic.com.tw>
Add a driver for Macronix MX25F0A multifunction device controller.
Signed-off-by: Mason Yang <masonccyang@mxic.com.tw>
---
drivers/mfd/Kconfig | 9 ++
drivers/mfd/Makefile | 1 +
drivers/mfd/mxic-mx25f0a.c | 84 +++++++++++++++++++
include/linux/mfd/mxic-mx25f0a.h | 175 +++++++++++++++++++++++++++++++++++++++
4 files changed, 269 insertions(+)
create mode 100644 drivers/mfd/mxic-mx25f0a.c
create mode 100644 include/linux/mfd/mxic-mx25f0a.h
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index 26ad646..7e99e93 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -823,6 +823,15 @@ config MFD_MAX8998
additional drivers must be enabled in order to use the functionality
of the device.
+config MFD_MXIC_MX25F0A
+ tristate "Macronix mx25f0a multifunction device support"
+ select MFD_CORE
+ help
+ This supports for Macronix mx25f0a multifunction device controller
+ for raw nand or spi. You have to select individual components like
+ raw nand controller or spi host controller under the corresponding
+ menus.
+
config MFD_MT6397
tristate "MediaTek MT6397 PMIC Support"
select MFD_CORE
diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
index b4569ed7..dcfe8fd 100644
--- a/drivers/mfd/Makefile
+++ b/drivers/mfd/Makefile
@@ -163,6 +163,7 @@ max8925-objs := max8925-core.o max8925-i2c.o
obj-$(CONFIG_MFD_MAX8925) += max8925.o
obj-$(CONFIG_MFD_MAX8997) += max8997.o max8997-irq.o
obj-$(CONFIG_MFD_MAX8998) += max8998.o max8998-irq.o
+obj-$(CONFIG_MFD_MXIC_MX25F0A) += mxic-mx25f0a.o
pcf50633-objs := pcf50633-core.o pcf50633-irq.o
obj-$(CONFIG_MFD_PCF50633) += pcf50633.o
diff --git a/drivers/mfd/mxic-mx25f0a.c b/drivers/mfd/mxic-mx25f0a.c
new file mode 100644
index 0000000..a884d97
--- /dev/null
+++ b/drivers/mfd/mxic-mx25f0a.c
@@ -0,0 +1,84 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (C) 2019 Macronix International Co., Ltd.
+//
+// Author:
+// Mason Yang <masonccyang@mxic.com.tw>
+//
+
+#include <linux/clk.h>
+#include <linux/mfd/mxic-mx25f0a.h>
+#include <linux/mfd/core.h>
+
+static const struct mfd_cell mx25f0a_nand_ctlr = {
+ .name = "mxic-nand-ctlr",
+ .of_compatible = "mxicy,mx25f0a-nand-ctlr",
+};
+
+static const struct mfd_cell mx25f0a_spi_ctlr = {
+ .name = "mxic-spi",
+ .of_compatible = "mxicy,mx25f0a-spi",
+};
+
+static int mx25f0a_mfd_probe(struct platform_device *pdev)
+{
+ const struct mfd_cell *cell;
+ struct mx25f0a_mfd *mxic;
+ struct resource *res;
+ int ret;
+
+ ret = of_device_is_compatible(pdev->dev.of_node->child,
+ "jedec,spi-nor");
+ if (ret)
+ cell = &mx25f0a_spi_ctlr;
+ else
+ cell = &mx25f0a_nand_ctlr;
+
+ mxic = devm_kzalloc(&pdev->dev, sizeof(*mxic), GFP_KERNEL);
+ if (!mxic)
+ return -ENOMEM;
+
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "regs");
+ mxic->regs = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(mxic->regs))
+ return PTR_ERR(mxic->regs);
+
+ if (cell == &mx25f0a_spi_ctlr) {
+ mxic->ps_clk = devm_clk_get(&pdev->dev, "ps_clk");
+ if (IS_ERR(mxic->ps_clk))
+ return PTR_ERR(mxic->ps_clk);
+
+ mxic->send_clk = devm_clk_get(&pdev->dev, "send_clk");
+ if (IS_ERR(mxic->send_clk))
+ return PTR_ERR(mxic->send_clk);
+
+ mxic->send_dly_clk = devm_clk_get(&pdev->dev, "send_dly_clk");
+ if (IS_ERR(mxic->send_dly_clk))
+ return PTR_ERR(mxic->send_dly_clk);
+ }
+
+ platform_set_drvdata(pdev, mxic);
+
+ ret = devm_mfd_add_devices(&pdev->dev, -1, cell, 1, NULL, 0, NULL);
+
+ return ret;
+}
+
+static const struct of_device_id mx25f0a_mfd_of_match[] = {
+ { .compatible = "mxic,mx25f0a", },
+ {},
+};
+MODULE_DEVICE_TABLE(of, mx25f0a_mfd_of_match);
+
+static struct platform_driver mx25f0a_mfd_driver = {
+ .probe = mx25f0a_mfd_probe,
+ .driver = {
+ .name = "mx25f0a-mfd",
+ .of_match_table = mx25f0a_mfd_of_match,
+ },
+};
+module_platform_driver(mx25f0a_mfd_driver);
+
+MODULE_AUTHOR("Mason Yang <masonccyang@mxic.com.tw>");
+MODULE_DESCRIPTION("MX25F0A controller MFD driver");
+MODULE_LICENSE("GPL v2");
diff --git a/include/linux/mfd/mxic-mx25f0a.h b/include/linux/mfd/mxic-mx25f0a.h
new file mode 100644
index 0000000..cb7bf19
--- /dev/null
+++ b/include/linux/mfd/mxic-mx25f0a.h
@@ -0,0 +1,175 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+//
+// Copyright (C) 2019 Macronix International Co., Ltd.
+//
+// Author:
+// Mason Yang <masonccyang@mxic.com.tw>
+//
+
+#ifndef __MFD_MXIC_MX25F0A_H
+#define __MFD_MXIC_MX25F0A_H
+
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/module.h>
+#include <linux/mtd/mtd.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+
+#define HC_CFG 0x0
+#define HC_CFG_IF_CFG(x) ((x) << 27)
+#define HC_CFG_DUAL_SLAVE BIT(31)
+#define HC_CFG_INDIVIDUAL BIT(30)
+#define HC_CFG_NIO(x) (((x) / 4) << 27)
+#define HC_CFG_TYPE(s, t) ((t) << (23 + ((s) * 2)))
+#define HC_CFG_TYPE_SPI_NOR 0
+#define HC_CFG_TYPE_SPI_NAND 1
+#define HC_CFG_TYPE_SPI_RAM 2
+#define HC_CFG_TYPE_RAW_NAND 3
+#define HC_CFG_SLV_ACT(x) ((x) << 21)
+#define HC_CFG_CLK_PH_EN BIT(20)
+#define HC_CFG_CLK_POL_INV BIT(19)
+#define HC_CFG_BIG_ENDIAN BIT(18)
+#define HC_CFG_DATA_PASS BIT(17)
+#define HC_CFG_IDLE_SIO_LVL(x) ((x) << 16)
+#define HC_CFG_MAN_START_EN BIT(3)
+#define HC_CFG_MAN_START BIT(2)
+#define HC_CFG_MAN_CS_EN BIT(1)
+#define HC_CFG_MAN_CS_ASSERT BIT(0)
+
+#define INT_STS 0x4
+#define INT_STS_EN 0x8
+#define INT_SIG_EN 0xc
+#define INT_STS_ALL GENMASK(31, 0)
+#define INT_RDY_PIN BIT(26)
+#define INT_RDY_SR BIT(25)
+#define INT_LNR_SUSP BIT(24)
+#define INT_ECC_ERR BIT(17)
+#define INT_CRC_ERR BIT(16)
+#define INT_LWR_DIS BIT(12)
+#define INT_LRD_DIS BIT(11)
+#define INT_SDMA_INT BIT(10)
+#define INT_DMA_FINISH BIT(9)
+#define INT_RX_NOT_FULL BIT(3)
+#define INT_RX_NOT_EMPTY BIT(2)
+#define INT_TX_NOT_FULL BIT(1)
+#define INT_TX_EMPTY BIT(0)
+
+#define HC_EN 0x10
+#define HC_EN_BIT BIT(0)
+
+#define TXD(x) (0x14 + ((x) * 4))
+#define RXD 0x24
+
+#define SS_CTRL(s) (0x30 + ((s) * 4))
+#define LRD_CFG 0x44
+#define LWR_CFG 0x80
+#define RWW_CFG 0x70
+#define OP_READ BIT(23)
+#define OP_DUMMY_CYC(x) ((x) << 17)
+#define OP_ADDR_BYTES(x) ((x) << 14)
+#define OP_CMD_BYTES(x) (((x) - 1) << 13)
+#define OP_OCTA_CRC_EN BIT(12)
+#define OP_DQS_EN BIT(11)
+#define OP_ENHC_EN BIT(10)
+#define OP_PREAMBLE_EN BIT(9)
+#define OP_DATA_DDR BIT(8)
+#define OP_DATA_BUSW(x) ((x) << 6)
+#define OP_ADDR_DDR BIT(5)
+#define OP_ADDR_BUSW(x) ((x) << 3)
+#define OP_CMD_DDR BIT(2)
+#define OP_CMD_BUSW(x) (x)
+#define OP_BUSW_1 0
+#define OP_BUSW_2 1
+#define OP_BUSW_4 2
+#define OP_BUSW_8 3
+
+#define OCTA_CRC 0x38
+#define OCTA_CRC_IN_EN(s) BIT(3 + ((s) * 16))
+#define OCTA_CRC_CHUNK(s, x) ((fls((x) / 32)) << (1 + ((s) * 16)))
+#define OCTA_CRC_OUT_EN(s) BIT(0 + ((s) * 16))
+
+#define ONFI_DIN_CNT(s) (0x3c + (s))
+
+#define LRD_CTRL 0x48
+#define RWW_CTRL 0x74
+#define LWR_CTRL 0x84
+#define LMODE_EN BIT(31)
+#define LMODE_SLV_ACT(x) ((x) << 21)
+#define LMODE_CMD1(x) ((x) << 8)
+#define LMODE_CMD0(x) (x)
+
+#define LRD_ADDR 0x4c
+#define LWR_ADDR 0x88
+#define LRD_RANGE 0x50
+#define LWR_RANGE 0x8c
+
+#define AXI_SLV_ADDR 0x54
+
+#define DMAC_RD_CFG 0x58
+#define DMAC_WR_CFG 0x94
+#define DMAC_CFG_PERIPH_EN BIT(31)
+#define DMAC_CFG_ALLFLUSH_EN BIT(30)
+#define DMAC_CFG_LASTFLUSH_EN BIT(29)
+#define DMAC_CFG_QE(x) (((x) + 1) << 16)
+#define DMAC_CFG_BURST_LEN(x) (((x) + 1) << 12)
+#define DMAC_CFG_BURST_SZ(x) ((x) << 8)
+#define DMAC_CFG_DIR_READ BIT(1)
+#define DMAC_CFG_START BIT(0)
+
+#define DMAC_RD_CNT 0x5c
+#define DMAC_WR_CNT 0x98
+
+#define SDMA_ADDR 0x60
+
+#define DMAM_CFG 0x64
+#define DMAM_CFG_START BIT(31)
+#define DMAM_CFG_CONT BIT(30)
+#define DMAM_CFG_SDMA_GAP(x) (fls((x) / 8192) << 2)
+#define DMAM_CFG_DIR_READ BIT(1)
+#define DMAM_CFG_EN BIT(0)
+
+#define DMAM_CNT 0x68
+
+#define LNR_TIMER_TH 0x6c
+
+#define RDM_CFG0 0x78
+#define RDM_CFG0_POLY(x) (x)
+
+#define RDM_CFG1 0x7c
+#define RDM_CFG1_RDM_EN BIT(31)
+#define RDM_CFG1_SEED(x) (x)
+
+#define LWR_SUSP_CTRL 0x90
+#define LWR_SUSP_CTRL_EN BIT(31)
+
+#define DMAS_CTRL 0x9c
+#define DMAS_CTRL_DIR_READ BIT(31)
+#define DMAS_CTRL_EN BIT(30)
+
+#define DATA_STROB 0xa0
+#define DATA_STROB_EDO_EN BIT(2)
+#define DATA_STROB_INV_POL BIT(1)
+#define DATA_STROB_DELAY_2CYC BIT(0)
+
+#define IDLY_CODE(x) (0xa4 + ((x) * 4))
+#define IDLY_CODE_VAL(x, v) ((v) << (((x) % 4) * 8))
+
+#define GPIO 0xc4
+#define GPIO_PT(x) BIT(3 + ((x) * 16))
+#define GPIO_RESET(x) BIT(2 + ((x) * 16))
+#define GPIO_HOLDB(x) BIT(1 + ((x) * 16))
+#define GPIO_WPB(x) BIT((x) * 16)
+
+#define HC_VER 0xd0
+
+#define HW_TEST(x) (0xe0 + ((x) * 4))
+
+struct mx25f0a_mfd {
+ void __iomem *regs;
+ struct clk *ps_clk;
+ struct clk *send_clk;
+ struct clk *send_dly_clk;
+};
+
+#endif // __MFD_MXIC_MX25F0A_H
--
1.9.1
next prev parent reply other threads:[~2019-04-09 2:11 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-04-09 2:29 [PATCH v2 0/4] Add Macronix MX25F0A MFD driver for raw nand and spi Mason Yang
2019-04-09 2:29 ` Mason Yang [this message]
2019-04-09 2:29 ` [PATCH v2 2/4] mtd: rawnand: Add Macronix MX25F0A NAND controller driver Mason Yang
2019-04-09 2:29 ` [PATCH v2 3/4] spi: Add MFD for Macronix MX25F0A SPI " Mason Yang
2019-04-10 9:37 ` Mark Brown
2019-04-09 2:30 ` [PATCH v2 4/4] dt-bindings: mfd: Document Macronix MX25F0A controller bindings Mason Yang
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1554777000-10542-2-git-send-email-masonccyang@mxic.com.tw \
--to=masonccyang@mxic.com.tw \
--cc=bbrezillon@kernel.org \
--cc=broonie@kernel.org \
--cc=christophe.kerello@st.com \
--cc=computersforpeace@gmal.com \
--cc=devicetree@vger.kernel.org \
--cc=dwmw2@infradead.org \
--cc=geert@linux-m68k.org \
--cc=juliensu@mxic.com.tw \
--cc=lee.jones@linaro.org \
--cc=liang.yang@amlogic.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mtd@lists.infradead.org \
--cc=linux-spi@vger.kernel.org \
--cc=marcel.ziswiler@toradex.com \
--cc=marek.vasut@gmail.com \
--cc=mark.rutland@arm.com \
--cc=miquel.raynal@bootlin.com \
--cc=paul.burton@mips.com \
--cc=richard@nod.at \
--cc=robh+dt@kernel.org \
--cc=stefan@agner.ch \
--cc=zhengxunli@mxic.com.tw \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).