From: Bjorn Andersson <bjorn.andersson@linaro.org>
To: Andy Gross <agross@kernel.org>, David Brown <david.brown@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>,
Mark Rutland <mark.rutland@arm.com>,
linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org
Subject: [PATCH v3] arm64: dts: qcom: qcs404: Add PCIe related nodes
Date: Wed, 1 May 2019 17:24:08 -0700 [thread overview]
Message-ID: <20190502002408.10719-1-bjorn.andersson@linaro.org> (raw)
The QCS404 has a PCIe2 PHY and a Qualcomm PCIe controller, add these to
the platform dtsi and enable them for the EVB with the perst gpio
and analog supplies defined.
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
---
The patch depends on the acceptance of:
https://lore.kernel.org/lkml/20190502002138.10646-1-bjorn.andersson@linaro.org/
https://lore.kernel.org/lkml/20190502001406.10431-2-bjorn.andersson@linaro.org/
https://lore.kernel.org/lkml/20190502001955.10575-3-bjorn.andersson@linaro.org/
Changes since v2:
- None
arch/arm64/boot/dts/qcom/qcs404-evb.dtsi | 25 +++++++++
arch/arm64/boot/dts/qcom/qcs404.dtsi | 67 ++++++++++++++++++++++++
2 files changed, 92 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi b/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi
index 2c3127167e3c..988d21ca0df1 100644
--- a/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi
+++ b/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi
@@ -68,6 +68,22 @@
};
};
+&pcie {
+ status = "ok";
+
+ perst-gpio = <&tlmm 43 GPIO_ACTIVE_LOW>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&perst_state>;
+};
+
+&pcie_phy {
+ status = "ok";
+
+ vdda-vp-supply = <&vreg_l3_1p05>;
+ vdda-vph-supply = <&vreg_l5_1p8>;
+};
+
&remoteproc_adsp {
status = "ok";
};
@@ -184,6 +200,15 @@
};
&tlmm {
+ perst_state: perst {
+ pins = "gpio43";
+ function = "gpio";
+
+ drive-strength = <2>;
+ bias-disable;
+ output-low;
+ };
+
sdc1_on: sdc1-on {
clk {
pins = "sdc1_clk";
diff --git a/arch/arm64/boot/dts/qcom/qcs404.dtsi b/arch/arm64/boot/dts/qcom/qcs404.dtsi
index ffedf9640af7..f41feab8996c 100644
--- a/arch/arm64/boot/dts/qcom/qcs404.dtsi
+++ b/arch/arm64/boot/dts/qcom/qcs404.dtsi
@@ -4,6 +4,7 @@
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/clock/qcom,gcc-qcs404.h>
#include <dt-bindings/clock/qcom,rpmcc.h>
+#include <dt-bindings/gpio/gpio.h>
/ {
interrupt-parent = <&intc>;
@@ -383,6 +384,7 @@
compatible = "qcom,gcc-qcs404";
reg = <0x01800000 0x80000>;
#clock-cells = <1>;
+ #reset-cells = <1>;
assigned-clocks = <&gcc GCC_APSS_AHB_CLK_SRC>;
assigned-clock-rates = <19200000>;
@@ -411,6 +413,21 @@
#interrupt-cells = <4>;
};
+ pcie_phy: phy@7786000 {
+ compatible = "qcom,qcs404-pcie2-phy", "qcom,pcie2-phy";
+ reg = <0x07786000 0xb8>;
+
+ clocks = <&gcc GCC_PCIE_0_PIPE_CLK>;
+ resets = <&gcc GCC_PCIEPHY_0_PHY_BCR>,
+ <&gcc GCC_PCIE_0_PIPE_ARES>;
+ reset-names = "phy", "pipe";
+
+ clock-output-names = "pcie_0_pipe_clk";
+ #phy-cells = <0>;
+
+ status = "disabled";
+ };
+
sdcc1: sdcc@7804000 {
compatible = "qcom,sdhci-msm-v5";
reg = <0x07804000 0x1000>, <0x7805000 0x1000>;
@@ -796,6 +813,56 @@
status = "disabled";
};
};
+
+ pcie: pci@10000000 {
+ compatible = "qcom,pcie-qcs404", "snps,dw-pcie";
+ reg = <0x10000000 0xf1d>,
+ <0x10000f20 0xa8>,
+ <0x07780000 0x2000>,
+ <0x10001000 0x2000>;
+ reg-names = "dbi", "elbi", "parf", "config";
+ device_type = "pci";
+ linux,pci-domain = <0>;
+ bus-range = <0x00 0xff>;
+ num-lanes = <1>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ ranges = <0x81000000 0 0 0x10003000 0 0x00010000>, /* I/O */
+ <0x82000000 0 0x10013000 0x10013000 0 0x007ed000>; /* memory */
+
+ interrupts = <GIC_SPI 266 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "msi";
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0x7>;
+ interrupt-map = <0 0 0 1 &intc GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+ <0 0 0 2 &intc GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+ <0 0 0 3 &intc GIC_SPI 267 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+ <0 0 0 4 &intc GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+ clocks = <&gcc GCC_PCIE_0_CFG_AHB_CLK>,
+ <&gcc GCC_PCIE_0_AUX_CLK>,
+ <&gcc GCC_PCIE_0_MSTR_AXI_CLK>,
+ <&gcc GCC_PCIE_0_SLV_AXI_CLK>;
+ clock-names = "iface", "aux", "master_bus", "slave_bus";
+
+ resets = <&gcc GCC_PCIE_0_AXI_MASTER_ARES>,
+ <&gcc GCC_PCIE_0_AXI_SLAVE_ARES>,
+ <&gcc GCC_PCIE_0_AXI_MASTER_STICKY_ARES>,
+ <&gcc GCC_PCIE_0_CORE_STICKY_ARES>,
+ <&gcc GCC_PCIE_0_BCR>,
+ <&gcc GCC_PCIE_0_AHB_ARES>;
+ reset-names = "axi_m",
+ "axi_s",
+ "axi_m_sticky",
+ "pipe_sticky",
+ "pwr",
+ "ahb";
+
+ phys = <&pcie_phy>;
+ phy-names = "pciephy";
+
+ status = "disabled";
+ };
};
timer {
--
2.18.0
next reply other threads:[~2019-05-02 0:24 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-05-02 0:24 Bjorn Andersson [this message]
2019-05-02 11:51 ` [PATCH v3] arm64: dts: qcom: qcs404: Add PCIe related nodes Vinod Koul
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190502002408.10719-1-bjorn.andersson@linaro.org \
--to=bjorn.andersson@linaro.org \
--cc=agross@kernel.org \
--cc=david.brown@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).