From: "Rafael J. Wysocki" <rjw@rjwysocki.net>
To: Linux PCI <linux-pci@vger.kernel.org>
Cc: Linux PM <linux-pm@vger.kernel.org>,
Linux ACPI <linux-acpi@vger.kernel.org>,
LKML <linux-kernel@vger.kernel.org>,
Bjorn Helgaas <helgaas@kernel.org>,
Mika Westerberg <mika.westerberg@linux.intel.com>,
Keith Busch <kbusch@kernel.org>
Subject: [PATCH] PCI: PM: Avoid possible suspend-to-idle issue
Date: Fri, 17 May 2019 11:08:50 +0200 [thread overview]
Message-ID: <2315917.ZGeXE6pBFC@kreacher> (raw)
From: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If a PCI driver leaves the device handled by it in D0 and calls
pci_save_state() on the device in its ->suspend() or ->suspend_late()
callback, it can expect the device to stay in D0 over the whole
s2idle cycle. However, that may not be the case if there is a
spurious wakeup while the system is suspended, because in that case
pci_pm_suspend_noirq() will run again after pci_pm_resume_noirq()
which calls pci_restore_state(), via pci_pm_default_resume_early(),
so state_saved is cleared and the second iteration of
pci_pm_suspend_noirq() will invoke pci_prepare_to_sleep() which
may change the power state of the device.
To avoid that, add a new internal flag, skip_bus_pm, that will be set
by pci_pm_suspend_noirq() when it runs for the first time during the
given system suspend-resume cycle if the state of the device has
been saved already and the device is still in D0. Setting that flag
will cause the next iterations of pci_pm_suspend_noirq() to set
state_saved for pci_pm_resume_noirq(), so that it always restores the
device state from the originally saved data, and avoid calling
pci_prepare_to_sleep() for the device.
Fixes: 33e4f80ee69b ("ACPI / PM: Ignore spurious SCI wakeups from suspend-to-idle")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
---
drivers/pci/pci-driver.c | 17 ++++++++++++++++-
include/linux/pci.h | 1 +
2 files changed, 17 insertions(+), 1 deletion(-)
Index: linux-pm/drivers/pci/pci-driver.c
===================================================================
--- linux-pm.orig/drivers/pci/pci-driver.c
+++ linux-pm/drivers/pci/pci-driver.c
@@ -734,6 +734,8 @@ static int pci_pm_suspend(struct device
struct pci_dev *pci_dev = to_pci_dev(dev);
const struct dev_pm_ops *pm = dev->driver ? dev->driver->pm : NULL;
+ pci_dev->skip_bus_pm = false;
+
if (pci_has_legacy_pm_support(pci_dev))
return pci_legacy_suspend(dev, PMSG_SUSPEND);
@@ -827,7 +829,20 @@ static int pci_pm_suspend_noirq(struct d
}
}
- if (!pci_dev->state_saved) {
+ if (pci_dev->skip_bus_pm) {
+ /*
+ * The function is running for the second time in a row without
+ * going through full resume, which is possible only during
+ * suspend-to-idle in a spurious wakeup case. Moreover, the
+ * device was originally left in D0, so its power state should
+ * not be changed here and the device register values saved
+ * originally should be restored on resume again.
+ */
+ pci_dev->state_saved = true;
+ } else if (pci_dev->state_saved) {
+ if (pci_dev->current_state == PCI_D0)
+ pci_dev->skip_bus_pm = true;
+ } else {
pci_save_state(pci_dev);
if (pci_power_manageable(pci_dev))
pci_prepare_to_sleep(pci_dev);
Index: linux-pm/include/linux/pci.h
===================================================================
--- linux-pm.orig/include/linux/pci.h
+++ linux-pm/include/linux/pci.h
@@ -344,6 +344,7 @@ struct pci_dev {
D3cold, not set for devices
powered on/off by the
corresponding bridge */
+ unsigned int skip_bus_pm:1; /* Internal: Skip bus-level PM */
unsigned int ignore_hotplug:1; /* Ignore hotplug events */
unsigned int hotplug_user_indicators:1; /* SlotCtl indicators
controlled exclusively by
next reply other threads:[~2019-05-17 9:08 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-05-17 9:08 Rafael J. Wysocki [this message]
2019-05-17 15:57 ` [PATCH] PCI: PM: Avoid possible suspend-to-idle issue Keith Busch
2019-05-20 10:39 ` Mika Westerberg
2019-05-27 11:02 ` Rafael J. Wysocki
2019-06-11 8:39 ` Kai-Heng Feng
2019-06-11 9:03 ` Rafael J. Wysocki
2019-06-11 21:34 ` Rafael J. Wysocki
2019-06-11 21:37 ` Rafael J. Wysocki
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=2315917.ZGeXE6pBFC@kreacher \
--to=rjw@rjwysocki.net \
--cc=helgaas@kernel.org \
--cc=kbusch@kernel.org \
--cc=linux-acpi@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pci@vger.kernel.org \
--cc=linux-pm@vger.kernel.org \
--cc=mika.westerberg@linux.intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).