From: Tony Lindgren <tony@atomide.com>
To: linux-omap@vger.kernel.org
Cc: Dave Gerlach <d-gerlach@ti.com>, Faiz Abbas <faiz_abbas@ti.com>,
Greg Kroah-Hartman <gregkh@linuxfoundation.org>,
Keerthy <j-keerthy@ti.com>, Nishanth Menon <nm@ti.com>,
Peter Ujfalusi <peter.ujfalusi@ti.com>,
Roger Quadros <rogerq@ti.com>, Suman Anna <s-anna@ti.com>,
Tero Kristo <t-kristo@ti.com>,
linux-kernel@vger.kernel.org,
linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org,
Rob Herring <robh@kernel.org>
Subject: [PATCH 13/13] ARM: dts: Drop legacy custom hwmods property for omap4 mmc
Date: Mon, 27 May 2019 23:24:14 -0700 [thread overview]
Message-ID: <20190528062414.27192-14-tony@atomide.com> (raw)
In-Reply-To: <20190528062414.27192-1-tony@atomide.com>
With recent ti-sysc driver changes, we can now finally probe most
modules without needing the custom ti,hwmods property.
Let's drop it for omap4 MMC as we can test that for runtime PM
for core retention idle mode for wlcore WLAN.
Cc: devicetree@vger.kernel.org
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/boot/dts/omap4-l4.dtsi | 5 -----
1 file changed, 5 deletions(-)
diff --git a/arch/arm/boot/dts/omap4-l4.dtsi b/arch/arm/boot/dts/omap4-l4.dtsi
--- a/arch/arm/boot/dts/omap4-l4.dtsi
+++ b/arch/arm/boot/dts/omap4-l4.dtsi
@@ -2103,7 +2103,6 @@
target-module@9c000 { /* 0x4809c000, ap 53 36.0 */
compatible = "ti,sysc-omap4", "ti,sysc";
- ti,hwmods = "mmc1";
reg = <0x9c000 0x4>,
<0x9c010 0x4>;
reg-names = "rev", "sysc";
@@ -2171,7 +2170,6 @@
target-module@ad000 { /* 0x480ad000, ap 63 50.0 */
compatible = "ti,sysc-omap4", "ti,sysc";
- ti,hwmods = "mmc3";
reg = <0xad000 0x4>,
<0xad010 0x4>;
reg-names = "rev", "sysc";
@@ -2237,7 +2235,6 @@
target-module@b4000 { /* 0x480b4000, ap 67 46.0 */
compatible = "ti,sysc-omap4", "ti,sysc";
- ti,hwmods = "mmc2";
reg = <0xb4000 0x4>,
<0xb4010 0x4>;
reg-names = "rev", "sysc";
@@ -2332,7 +2329,6 @@
target-module@d1000 { /* 0x480d1000, ap 73 44.0 */
compatible = "ti,sysc-omap4", "ti,sysc";
- ti,hwmods = "mmc4";
reg = <0xd1000 0x4>,
<0xd1010 0x4>;
reg-names = "rev", "sysc";
@@ -2365,7 +2361,6 @@
target-module@d5000 { /* 0x480d5000, ap 75 4e.0 */
compatible = "ti,sysc-omap4", "ti,sysc";
- ti,hwmods = "mmc5";
reg = <0xd5000 0x4>,
<0xd5010 0x4>;
reg-names = "rev", "sysc";
--
2.21.0
next prev parent reply other threads:[~2019-05-28 6:24 UTC|newest]
Thread overview: 15+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-05-28 6:24 [PATCHv2 00/13] ti-sysc driver changes to drop custom hwmods property Tony Lindgren
2019-05-28 6:24 ` [PATCH 01/13] bus: ti-sysc: Add support for missing clockdomain handling Tony Lindgren
2019-05-28 6:24 ` [PATCH 02/13] bus: ti-sysc: Support 16-bit writes too Tony Lindgren
2019-05-28 6:24 ` [PATCH 03/13] bus: ti-sysc: Make OCP reset work for sysstatus and sysconfig reset bits Tony Lindgren
2019-05-28 6:24 ` [PATCH 04/13] bus: ti-sysc: Allow QUIRK_LEGACY_IDLE even if legacy_mode is not set Tony Lindgren
2019-05-28 6:24 ` [PATCH 05/13] bus: ti-sysc: Enable interconnect target module autoidle bit on enable Tony Lindgren
2019-05-28 6:24 ` [PATCH 06/13] bus: ti-sysc: Handle clockactivity for enable and disable Tony Lindgren
2019-05-28 6:24 ` [PATCH 07/13] bus: ti-sysc: Handle swsup idle mode quirks Tony Lindgren
2019-05-28 6:24 ` [PATCH 08/13] bus: ti-sysc: Set ENAWAKEUP if available Tony Lindgren
2019-05-28 6:24 ` [PATCH 09/13] bus: ti-sysc: Add support for disabling module without legacy mode Tony Lindgren
2019-05-28 6:24 ` [PATCH 10/13] bus: ti-sysc: Do rstctrl reset handling in two phases Tony Lindgren
2019-05-28 6:24 ` [PATCH 11/13] bus: ti-sysc: Detect uarts also on omap34xx Tony Lindgren
2019-05-28 6:24 ` [PATCH 12/13] ARM: dts: Drop legacy custom hwmods property for omap4 uart Tony Lindgren
2019-05-28 6:24 ` Tony Lindgren [this message]
2019-05-28 8:02 ` [PATCHv2 00/13] ti-sysc driver changes to drop custom hwmods property Keerthy
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190528062414.27192-14-tony@atomide.com \
--to=tony@atomide.com \
--cc=d-gerlach@ti.com \
--cc=devicetree@vger.kernel.org \
--cc=faiz_abbas@ti.com \
--cc=gregkh@linuxfoundation.org \
--cc=j-keerthy@ti.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-omap@vger.kernel.org \
--cc=nm@ti.com \
--cc=peter.ujfalusi@ti.com \
--cc=robh@kernel.org \
--cc=rogerq@ti.com \
--cc=s-anna@ti.com \
--cc=t-kristo@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).