From: Vijay Khemka <vijaykhemka@fb.com>
To: Jean Delvare <jdelvare@suse.com>,
Guenter Roeck <linux@roeck-us.net>,
Jonathan Corbet <corbet@lwn.net>, <linux-hwmon@vger.kernel.org>,
<linux-doc@vger.kernel.org>, <linux-kernel@vger.kernel.org>
Cc: <vijaykhemka@fb.com>, <joel@jms.id.au>,
<linux-aspeed@lists.ozlabs.org>, <sdasari@fb.com>,
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Subject: [PATCH 2/2] Docs: hwmon: pmbus: Add PXE1610 driver
Date: Wed, 29 May 2019 15:35:09 -0700 [thread overview]
Message-ID: <20190529223511.4059120-2-vijaykhemka@fb.com> (raw)
In-Reply-To: <20190529223511.4059120-1-vijaykhemka@fb.com>
Added support for Infenion PXE1610 driver
Signed-off-by: Vijay Khemka <vijaykhemka@fb.com>
---
Documentation/hwmon/pxe1610 | 84 +++++++++++++++++++++++++++++++++++++
1 file changed, 84 insertions(+)
create mode 100644 Documentation/hwmon/pxe1610
diff --git a/Documentation/hwmon/pxe1610 b/Documentation/hwmon/pxe1610
new file mode 100644
index 000000000000..b5c83edf027a
--- /dev/null
+++ b/Documentation/hwmon/pxe1610
@@ -0,0 +1,84 @@
+Kernel driver pxe1610
+=====================
+
+Supported chips:
+ * Infinion PXE1610
+ Prefix: 'pxe1610'
+ Addresses scanned: -
+ Datasheet: Datasheet is not publicly available.
+
+ * Infinion PXE1110
+ Prefix: 'pxe1110'
+ Addresses scanned: -
+ Datasheet: Datasheet is not publicly available.
+
+ * Infinion PXM1310
+ Prefix: 'pxm1310'
+ Addresses scanned: -
+ Datasheet: Datasheet is not publicly available.
+
+Author: Vijay Khemka <vijaykhemka@fb.com>
+
+
+Description
+-----------
+
+PXE1610 is a Multi-rail/Multiphase Digital Controllers and
+it is compliant to Intel VR13 DC-DC converter specifications.
+
+
+Usage Notes
+-----------
+
+This driver can be enabled with kernel config CONFIG_SENSORS_PXE1610
+set to 'y' or 'm'(for module).
+
+This driver does not probe for PMBus devices. You will have
+to instantiate devices explicitly.
+
+Example: the following commands will load the driver for an PXE1610
+at address 0x70 on I2C bus #4:
+
+# modprobe pxe1610
+# echo pxe1610 0x70 > /sys/bus/i2c/devices/i2c-4/new_device
+
+It can also be instantiated by declaring in device tree if it is
+built as a kernel not as a module.
+
+
+Sysfs attributes
+----------------
+
+curr1_label "iin"
+curr1_input Measured input current
+curr1_alarm Current high alarm
+
+curr[2-4]_label "iout[1-3]"
+curr[2-4]_input Measured output current
+curr[2-4]_crit Critical maximum current
+curr[2-4]_crit_alarm Current critical high alarm
+
+in1_label "vin"
+in1_input Measured input voltage
+in1_crit Critical maximum input voltage
+in1_crit_alarm Input voltage critical high alarm
+
+in[2-4]_label "vout[1-3]"
+in[2-4]_input Measured output voltage
+in[2-4]_lcrit Critical minimum output voltage
+in[2-4]_lcrit_alarm Output voltage critical low alarm
+in[2-4]_crit Critical maximum output voltage
+in[2-4]_crit_alarm Output voltage critical high alarm
+
+power1_label "pin"
+power1_input Measured input power
+power1_alarm Input power high alarm
+
+power[2-4]_label "pout[1-3]"
+power[2-4]_input Measured output power
+
+temp[1-3]_input Measured temperature
+temp[1-3]_crit Critical high temperature
+temp[1-3]_crit_alarm Chip temperature critical high alarm
+temp[1-3]_max Maximum temperature
+temp[1-3]_max_alarm Chip temperature high alarm
--
2.17.1
next prev parent reply other threads:[~2019-05-29 22:35 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-05-29 22:35 [PATCH 1/2] hwmon: pmbus: Add Infineon PXE1610 VR driver Vijay Khemka
2019-05-29 22:35 ` Vijay Khemka [this message]
2019-05-30 1:05 ` [PATCH 2/2] Docs: hwmon: pmbus: Add PXE1610 driver Guenter Roeck
2019-05-30 18:51 ` Vijay Khemka
2019-05-30 19:44 ` Guenter Roeck
2019-05-30 20:44 ` Vijay Khemka
2019-05-30 1:00 ` [PATCH 1/2] hwmon: pmbus: Add Infineon PXE1610 VR driver Guenter Roeck
2019-05-30 18:55 ` Vijay Khemka
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190529223511.4059120-2-vijaykhemka@fb.com \
--to=vijaykhemka@fb.com \
--cc=corbet@lwn.net \
--cc=gregkh@linuxfoundation.org \
--cc=jdelvare@suse.com \
--cc=joel@jms.id.au \
--cc=linux-aspeed@lists.ozlabs.org \
--cc=linux-doc@vger.kernel.org \
--cc=linux-hwmon@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux@roeck-us.net \
--cc=sdasari@fb.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).