From: Yangtao Li <tiny.windzz@gmail.com>
To: vireshk@kernel.org, nm@ti.com, sboyd@kernel.org,
robh+dt@kernel.org, mark.rutland@arm.com,
maxime.ripard@bootlin.com, wens@csie.org, rjw@rjwysocki.net,
davem@davemloft.net, mchehab+samsung@kernel.org,
gregkh@linuxfoundation.org, linus.walleij@linaro.org,
nicolas.ferre@microchip.com, paulmck@linux.ibm.com
Cc: linux-pm@vger.kernel.org, devicetree@vger.kernel.org,
linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org, Yangtao Li <tiny.windzz@gmail.com>
Subject: [RESEND, PATCH v4 2/2] dt-bindings: cpufreq: Document allwinner,sun50i-h6-operating-points
Date: Wed, 12 Jun 2019 12:28:16 -0400 [thread overview]
Message-ID: <20190612162816.31713-3-tiny.windzz@gmail.com> (raw)
In-Reply-To: <20190612162816.31713-1-tiny.windzz@gmail.com>
Allwinner Process Voltage Scaling Tables defines the voltage and
frequency value based on the speedbin blown in the efuse combination.
The sunxi-cpufreq-nvmem driver reads the efuse value from the SoC to
provide the OPP framework with required information.
This is used to determine the voltage and frequency value for each
OPP of operating-points-v2 table when it is parsed by the OPP framework.
The "allwinner,sun50i-h6-operating-points" DT extends the
"operating-points-v2"
with following parameters:
- nvmem-cells (NVMEM area containig the speedbin information)
- opp-microvolt-<name>: voltage in micro Volts.
At runtime, the platform can pick a <name> and matching
opp-microvolt-<name> property.
HW: <name>:
sun50i-h6 speed0 speed1 speed2
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
---
.../bindings/opp/sun50i-nvmem-cpufreq.txt | 167 ++++++++++++++++++
1 file changed, 167 insertions(+)
create mode 100644 Documentation/devicetree/bindings/opp/sun50i-nvmem-cpufreq.txt
diff --git a/Documentation/devicetree/bindings/opp/sun50i-nvmem-cpufreq.txt b/Documentation/devicetree/bindings/opp/sun50i-nvmem-cpufreq.txt
new file mode 100644
index 000000000000..7deae57a587b
--- /dev/null
+++ b/Documentation/devicetree/bindings/opp/sun50i-nvmem-cpufreq.txt
@@ -0,0 +1,167 @@
+Allwinner Technologies, Inc. NVMEM CPUFreq and OPP bindings
+===================================
+
+For some SoCs, the CPU frequency subset and voltage value of each OPP
+varies based on the silicon variant in use. Allwinner Process Voltage
+Scaling Tables defines the voltage and frequency value based on the
+speedbin blown in the efuse combination. The sun50i-cpufreq-nvmem driver
+reads the efuse value from the SoC to provide the OPP framework with
+required information.
+
+Required properties:
+--------------------
+In 'cpus' nodes:
+- operating-points-v2: Phandle to the operating-points-v2 table to use.
+
+In 'operating-points-v2' table:
+- compatible: Should be
+ - 'allwinner,sun50i-h6-operating-points'.
+- nvmem-cells: A phandle pointing to a nvmem-cells node representing the
+ efuse registers that has information about the speedbin
+ that is used to select the right frequency/voltage value
+ pair. Please refer the for nvmem-cells bindings
+ Documentation/devicetree/bindings/nvmem/nvmem.txt and
+ also examples below.
+
+In every OPP node:
+- opp-microvolt-<name>: Voltage in micro Volts.
+ At runtime, the platform can pick a <name> and
+ matching opp-microvolt-<name> property.
+ [See: opp.txt]
+ HW: <name>:
+ sun50i-h6 speed0 speed1 speed2
+
+Example 1:
+---------
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: cpu@0 {
+ compatible = "arm,cortex-a53";
+ device_type = "cpu";
+ reg = <0>;
+ enable-method = "psci";
+ clocks = <&ccu CLK_CPUX>;
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ operating-points-v2 = <&cpu_opp_table>;
+ #cooling-cells = <2>;
+ };
+
+ cpu1: cpu@1 {
+ compatible = "arm,cortex-a53";
+ device_type = "cpu";
+ reg = <1>;
+ enable-method = "psci";
+ clocks = <&ccu CLK_CPUX>;
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ operating-points-v2 = <&cpu_opp_table>;
+ #cooling-cells = <2>;
+ };
+
+ cpu2: cpu@2 {
+ compatible = "arm,cortex-a53";
+ device_type = "cpu";
+ reg = <2>;
+ enable-method = "psci";
+ clocks = <&ccu CLK_CPUX>;
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ operating-points-v2 = <&cpu_opp_table>;
+ #cooling-cells = <2>;
+ };
+
+ cpu3: cpu@3 {
+ compatible = "arm,cortex-a53";
+ device_type = "cpu";
+ reg = <3>;
+ enable-method = "psci";
+ clocks = <&ccu CLK_CPUX>;
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ operating-points-v2 = <&cpu_opp_table>;
+ #cooling-cells = <2>;
+ };
+ };
+
+ cpu_opp_table: opp_table {
+ compatible = "allwinner,sun50i-h6-operating-points";
+ nvmem-cells = <&speedbin_efuse>;
+ opp-shared;
+
+ opp@480000000 {
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ opp-hz = /bits/ 64 <480000000>;
+
+ opp-microvolt-speed0 = <880000>;
+ opp-microvolt-speed1 = <820000>;
+ opp-microvolt-speed2 = <800000>;
+ };
+
+ opp@720000000 {
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ opp-hz = /bits/ 64 <720000000>;
+
+ opp-microvolt-speed0 = <880000>;
+ opp-microvolt-speed1 = <820000>;
+ opp-microvolt-speed2 = <800000>;
+ };
+
+ opp@816000000 {
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ opp-hz = /bits/ 64 <816000000>;
+
+ opp-microvolt-speed0 = <880000>;
+ opp-microvolt-speed1 = <820000>;
+ opp-microvolt-speed2 = <800000>;
+ };
+
+ opp@888000000 {
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ opp-hz = /bits/ 64 <888000000>;
+
+ opp-microvolt-speed0 = <940000>;
+ opp-microvolt-speed1 = <820000>;
+ opp-microvolt-speed2 = <800000>;
+ };
+
+ opp@1080000000 {
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ opp-hz = /bits/ 64 <1080000000>;
+
+ opp-microvolt-speed0 = <1060000>;
+ opp-microvolt-speed1 = <880000>;
+ opp-microvolt-speed2 = <840000>;
+ };
+
+ opp@1320000000 {
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ opp-hz = /bits/ 64 <1320000000>;
+
+ opp-microvolt-speed0 = <1160000>;
+ opp-microvolt-speed1 = <940000>;
+ opp-microvolt-speed2 = <900000>;
+ };
+
+ opp@1488000000 {
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ opp-hz = /bits/ 64 <1488000000>;
+
+ opp-microvolt-speed0 = <1160000>;
+ opp-microvolt-speed1 = <1000000>;
+ opp-microvolt-speed2 = <960000>;
+ };
+ };
+....
+soc {
+....
+ sid: sid@3006000 {
+ compatible = "allwinner,sun50i-h6-sid";
+ reg = <0x03006000 0x400>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ....
+ speedbin_efuse: speed@1c {
+ reg = <0x1c 4>;
+ };
+ };
+};
--
2.17.0
next prev parent reply other threads:[~2019-06-12 16:28 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-06-12 16:28 [RESEND, PATCH v4 0/2] cpufreq: Add sunxi nvmem based CPU scaling driver Yangtao Li
2019-06-12 16:28 ` [RESEND, PATCH v4 1/2] cpufreq: Add sun50i " Yangtao Li
2019-06-12 16:28 ` Yangtao Li [this message]
2019-07-09 14:31 ` [RESEND, PATCH v4 2/2] dt-bindings: cpufreq: Document allwinner,sun50i-h6-operating-points Rob Herring
2019-06-12 16:33 ` [RESEND, PATCH v4 0/2] cpufreq: Add sunxi nvmem based CPU scaling driver Frank Lee
2019-07-10 9:15 ` Viresh Kumar
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190612162816.31713-3-tiny.windzz@gmail.com \
--to=tiny.windzz@gmail.com \
--cc=davem@davemloft.net \
--cc=devicetree@vger.kernel.org \
--cc=gregkh@linuxfoundation.org \
--cc=linus.walleij@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pm@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=maxime.ripard@bootlin.com \
--cc=mchehab+samsung@kernel.org \
--cc=nicolas.ferre@microchip.com \
--cc=nm@ti.com \
--cc=paulmck@linux.ibm.com \
--cc=rjw@rjwysocki.net \
--cc=robh+dt@kernel.org \
--cc=sboyd@kernel.org \
--cc=vireshk@kernel.org \
--cc=wens@csie.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).