From: Yangtao Li <tiny.windzz@gmail.com>
To: rui.zhang@intel.com, edubezval@gmail.com,
daniel.lezcano@linaro.org, robh+dt@kernel.org,
mark.rutland@arm.com, maxime.ripard@bootlin.com, wens@csie.org,
davem@davemloft.net, gregkh@linuxfoundation.org,
mchehab+samsung@kernel.org, linus.walleij@linaro.org,
nicolas.ferre@microchip.com, paulmck@linux.ibm.com
Cc: linux-pm@vger.kernel.org, devicetree@vger.kernel.org,
linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org, Yangtao Li <tiny.windzz@gmail.com>
Subject: [PATCH v4 05/11] thermal: sun8i: rework for sun8i_ths_get_temp()
Date: Sun, 23 Jun 2019 12:42:00 -0400 [thread overview]
Message-ID: <20190623164206.7467-6-tiny.windzz@gmail.com> (raw)
In-Reply-To: <20190623164206.7467-1-tiny.windzz@gmail.com>
For different socs, the way they get and calculate the
temperature is roughly the same. So get the difference
from device compatible.
Difference point:
1) temperature calculation formula parameters
2) ths data register start address
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
---
drivers/thermal/sun8i_thermal.c | 17 +++++++++++------
1 file changed, 11 insertions(+), 6 deletions(-)
diff --git a/drivers/thermal/sun8i_thermal.c b/drivers/thermal/sun8i_thermal.c
index c37e1c51a543..e473a5651436 100644
--- a/drivers/thermal/sun8i_thermal.c
+++ b/drivers/thermal/sun8i_thermal.c
@@ -22,9 +22,6 @@
#define MAX_SENSOR_NUM 4
-#define SUN50I_H6_OFFSET -2794
-#define SUN50I_H6_SCALE -67
-
#define FT_TEMP_MASK GENMASK(11, 0)
#define TEMP_CALIB_MASK GENMASK(11, 0)
#define TEMP_TO_REG 672
@@ -58,6 +55,10 @@ struct tsensor {
struct ths_thermal_chip {
int sensor_num;
+ int offset;
+ int scale;
+ int ft_deviation;
+ int temp_data_base;
};
struct ths_device {
@@ -73,7 +74,7 @@ struct ths_device {
static int sun8i_ths_reg2temp(struct ths_device *tmdev,
int reg)
{
- return (reg + SUN50I_H6_OFFSET) * SUN50I_H6_SCALE;
+ return (reg + tmdev->chip->offset) * tmdev->chip->scale;
}
static int sun8i_ths_get_temp(void *data, int *temp)
@@ -82,7 +83,7 @@ static int sun8i_ths_get_temp(void *data, int *temp)
struct ths_device *tmdev = s->tmdev;
int val;
- regmap_read(tmdev->regmap, SUN50I_H6_THS_TEMP_DATA +
+ regmap_read(tmdev->regmap, tmdev->chip->temp_data_base +
0x4 * s->id, &val);
/* ths have no data yet */
@@ -98,7 +99,7 @@ static int sun8i_ths_get_temp(void *data, int *temp)
* temperature above is also used when the sensor is calibrated. If
* do this, the correct calibration formula is hard to know.
*/
- *temp += SUN50I_H6_FT_DEVIATION;
+ *temp += tmdev->chip->ft_deviation;
return 0;
}
@@ -395,6 +396,10 @@ static int sun8i_ths_remove(struct platform_device *pdev)
static const struct ths_thermal_chip sun50i_h6_ths = {
.sensor_num = 2,
+ .offset = -2794,
+ .scale = -67,
+ .ft_deviation = SUN50I_H6_FT_DEVIATION,
+ .temp_data_base = SUN50I_H6_THS_TEMP_DATA,
};
static const struct of_device_id of_ths_match[] = {
--
2.17.1
next prev parent reply other threads:[~2019-06-23 16:42 UTC|newest]
Thread overview: 23+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-06-23 16:41 [PATCH v4 00/11] add thermal driver for h6 Yangtao Li
2019-06-23 16:41 ` [PATCH v4 01/11] thermal: sun8i: " Yangtao Li
2019-06-24 12:07 ` Ondřej Jirman
2019-06-23 16:41 ` [PATCH v4 02/11] dt-bindings: thermal: add binding document for h6 thermal controller Yangtao Li
2019-06-24 8:47 ` Maxime Ripard
2019-06-23 16:41 ` [PATCH v4 03/11] thermal: fix indentation in makefile Yangtao Li
2019-06-23 16:41 ` [PATCH v4 04/11] thermal: sun8i: get ths sensor number from device compatible Yangtao Li
2019-06-23 16:42 ` Yangtao Li [this message]
2019-06-23 16:42 ` [PATCH v4 06/11] thermal: sun8i: get ths init func " Yangtao Li
2019-06-23 16:42 ` [PATCH v4 07/11] thermal: sun8i: rework for ths irq handler func Yangtao Li
2019-06-23 16:42 ` [PATCH v4 08/11] thermal: sun8i: support ahb clocks Yangtao Li
2019-06-24 18:23 ` Maxime Ripard
2019-06-25 0:34 ` Ondřej Jirman
2019-06-25 8:25 ` Maxime Ripard
2019-06-23 16:42 ` [PATCH v4 09/11] thermal: sun8i: rework for ths calibrate func Yangtao Li
2019-06-23 16:42 ` [PATCH v4 10/11] dt-bindings: thermal: add binding document for h3 thermal controller Yangtao Li
2019-06-24 8:50 ` Maxime Ripard
2019-06-23 16:42 ` [PATCH v4 11/11] thermal: sun8i: add thermal driver for h3 Yangtao Li
2019-06-24 12:05 ` Ondřej Jirman
2019-07-10 23:09 ` [PATCH v4 00/11] add thermal driver for h6 Vasily Khoruzhick
2019-07-13 18:01 ` Vasily Khoruzhick
2019-07-26 17:46 ` Vasily Khoruzhick
2019-07-28 12:11 ` Frank Lee
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190623164206.7467-6-tiny.windzz@gmail.com \
--to=tiny.windzz@gmail.com \
--cc=daniel.lezcano@linaro.org \
--cc=davem@davemloft.net \
--cc=devicetree@vger.kernel.org \
--cc=edubezval@gmail.com \
--cc=gregkh@linuxfoundation.org \
--cc=linus.walleij@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pm@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=maxime.ripard@bootlin.com \
--cc=mchehab+samsung@kernel.org \
--cc=nicolas.ferre@microchip.com \
--cc=paulmck@linux.ibm.com \
--cc=robh+dt@kernel.org \
--cc=rui.zhang@intel.com \
--cc=wens@csie.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).