linux-kernel.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Jonathan Chocron <jonnyc@amazon.com>
To: <lorenzo.pieralisi@arm.com>, <bhelgaas@google.com>,
	<jingoohan1@gmail.com>, <gustavo.pimentel@synopsys.com>,
	<robh+dt@kernel.org>, <mark.rutland@arm.com>
Cc: <dwmw@amazon.co.uk>, <benh@kernel.crashing.org>,
	<alisaidi@amazon.com>, <ronenk@amazon.com>, <barakw@amazon.com>,
	<talel@amazon.com>, <hanochu@amazon.com>, <hhhawa@amazon.com>,
	<linux-pci@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
	<devicetree@vger.kernel.org>, <jonnyc@amazon.com>
Subject: [PATCH v3 6/8] PCI: al: Add support for DW based driver type
Date: Tue, 23 Jul 2019 12:27:09 +0300	[thread overview]
Message-ID: <20190723092711.11786-2-jonnyc@amazon.com> (raw)
In-Reply-To: <20190723092529.11310-1-jonnyc@amazon.com>

This driver is DT based and utilizes the DesignWare APIs.
It allows using a smaller ECAM range for a larger bus range -
usually an entire bus uses 1MB of address space, but the driver
can use it for a larger number of buses.

All link initializations are handled by the boot FW.

Signed-off-by: Jonathan Chocron <jonnyc@amazon.com>
---
 drivers/pci/controller/dwc/Kconfig   |  12 +
 drivers/pci/controller/dwc/pcie-al.c | 367 +++++++++++++++++++++++++++
 2 files changed, 379 insertions(+)

diff --git a/drivers/pci/controller/dwc/Kconfig b/drivers/pci/controller/dwc/Kconfig
index 6ea778ae4877..3c6094cbcc3b 100644
--- a/drivers/pci/controller/dwc/Kconfig
+++ b/drivers/pci/controller/dwc/Kconfig
@@ -230,4 +230,16 @@ config PCIE_UNIPHIER
 	  Say Y here if you want PCIe controller support on UniPhier SoCs.
 	  This driver supports LD20 and PXs3 SoCs.
 
+config PCIE_AL
+	bool "Amazon Annapurna Labs PCIe controller"
+	depends on OF && (ARM64 || COMPILE_TEST)
+	depends on PCI_MSI_IRQ_DOMAIN
+	select PCIE_DW_HOST
+	help
+	  Say Y here to enable support of the Amazon's Annapurna Labs PCIe
+	  controller IP on Amazon SoCs. The PCIe controller uses the DesignWare
+	  core plus Annapurna Labs proprietary hardware wrappers. This is
+	  required only for DT-based platforms. ACPI platforms with the
+	  Annapurna Labs PCIe controller don't need to enable this.
+
 endmenu
diff --git a/drivers/pci/controller/dwc/pcie-al.c b/drivers/pci/controller/dwc/pcie-al.c
index 3ab58f0584a8..3ffdd3c97617 100644
--- a/drivers/pci/controller/dwc/pcie-al.c
+++ b/drivers/pci/controller/dwc/pcie-al.c
@@ -91,3 +91,370 @@ struct pci_ecam_ops al_pcie_ops = {
 };
 
 #endif /* defined(CONFIG_ACPI) && defined(CONFIG_PCI_QUIRKS) */
+
+#ifdef CONFIG_PCIE_AL
+
+#include <linux/of_pci.h>
+#include "pcie-designware.h"
+
+#define AL_PCIE_REV_ID_2	2
+#define AL_PCIE_REV_ID_3	3
+#define AL_PCIE_REV_ID_4	4
+
+#define AXI_BASE_OFFSET		0x0
+
+#define DEVICE_ID_OFFSET	0x16c
+
+#define DEVICE_REV_ID			0x0
+#define DEVICE_REV_ID_DEV_ID_MASK	GENMASK(31, 16)
+
+#define DEVICE_REV_ID_DEV_ID_X4		0
+#define DEVICE_REV_ID_DEV_ID_X8		2
+#define DEVICE_REV_ID_DEV_ID_X16	4
+
+#define OB_CTRL_REV1_2_OFFSET	0x0040
+#define OB_CTRL_REV3_5_OFFSET	0x0030
+
+#define CFG_TARGET_BUS			0x0
+#define CFG_TARGET_BUS_MASK_MASK	GENMASK(7, 0)
+#define CFG_TARGET_BUS_BUSNUM_MASK	GENMASK(15, 8)
+
+#define CFG_CONTROL			0x4
+#define CFG_CONTROL_SUBBUS_MASK		GENMASK(15, 8)
+#define CFG_CONTROL_SEC_BUS_MASK	GENMASK(23, 16)
+
+struct al_pcie_reg_offsets {
+	unsigned int ob_ctrl;
+};
+
+struct al_pcie_target_bus_cfg {
+	u8 reg_val;
+	u8 reg_mask;
+	u8 ecam_mask;
+};
+
+struct al_pcie {
+	struct dw_pcie *pci;
+	void __iomem *controller_base; /* base of PCIe unit (not DW core) */
+	struct device *dev;
+	resource_size_t ecam_size;
+	unsigned int controller_rev_id;
+	struct al_pcie_reg_offsets reg_offsets;
+	struct al_pcie_target_bus_cfg target_bus_cfg;
+};
+
+#define PCIE_ECAM_DEVFN(x)		(((x) & 0xff) << 12)
+
+#define to_al_pcie(x)		dev_get_drvdata((x)->dev)
+
+static inline u32 al_pcie_controller_readl(struct al_pcie *pcie, u32 offset)
+{
+	return readl(pcie->controller_base + offset);
+}
+
+static inline void al_pcie_controller_writel(struct al_pcie *pcie, u32 offset,
+					     u32 val)
+{
+	writel(val, pcie->controller_base + offset);
+}
+
+static int al_pcie_rev_id_get(struct al_pcie *pcie, unsigned int *rev_id)
+{
+	u32 dev_rev_id_val;
+	u32 dev_id_val;
+
+	dev_rev_id_val = al_pcie_controller_readl(pcie, AXI_BASE_OFFSET +
+						  DEVICE_ID_OFFSET +
+						  DEVICE_REV_ID);
+	dev_id_val = FIELD_GET(DEVICE_REV_ID_DEV_ID_MASK, dev_rev_id_val);
+
+	switch (dev_id_val) {
+	case DEVICE_REV_ID_DEV_ID_X4:
+		*rev_id = AL_PCIE_REV_ID_2;
+		break;
+	case DEVICE_REV_ID_DEV_ID_X8:
+		*rev_id = AL_PCIE_REV_ID_3;
+		break;
+	case DEVICE_REV_ID_DEV_ID_X16:
+		*rev_id = AL_PCIE_REV_ID_4;
+		break;
+	default:
+		dev_err(pcie->dev, "Unsupported dev_id_val (0x%x)\n",
+			dev_id_val);
+		return -EINVAL;
+	}
+
+	dev_dbg(pcie->dev, "dev_id_val: 0x%x\n", dev_id_val);
+
+	return 0;
+}
+
+static int al_pcie_reg_offsets_set(struct al_pcie *pcie)
+{
+	switch (pcie->controller_rev_id) {
+	case AL_PCIE_REV_ID_2:
+		pcie->reg_offsets.ob_ctrl = OB_CTRL_REV1_2_OFFSET;
+		break;
+	case AL_PCIE_REV_ID_3:
+	case AL_PCIE_REV_ID_4:
+		pcie->reg_offsets.ob_ctrl = OB_CTRL_REV3_5_OFFSET;
+		break;
+	default:
+		dev_err(pcie->dev, "Unsupported controller rev_id: 0x%x\n",
+			pcie->controller_rev_id);
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static inline void al_pcie_target_bus_set(struct al_pcie *pcie,
+					  u8 target_bus,
+					  u8 mask_target_bus)
+{
+	u32 reg;
+
+	reg = FIELD_PREP(CFG_TARGET_BUS_MASK_MASK, mask_target_bus) |
+	      FIELD_PREP(CFG_TARGET_BUS_BUSNUM_MASK, target_bus);
+
+	al_pcie_controller_writel(pcie, AXI_BASE_OFFSET +
+				  pcie->reg_offsets.ob_ctrl + CFG_TARGET_BUS,
+				  reg);
+}
+
+static void __iomem *al_pcie_conf_addr_map(struct al_pcie *pcie,
+					   unsigned int busnr,
+					   unsigned int devfn)
+{
+	struct al_pcie_target_bus_cfg *target_bus_cfg = &pcie->target_bus_cfg;
+	unsigned int busnr_ecam = busnr & target_bus_cfg->ecam_mask;
+	unsigned int busnr_reg = busnr & target_bus_cfg->reg_mask;
+	struct pcie_port *pp = &pcie->pci->pp;
+	void __iomem *pci_base_addr;
+
+	pci_base_addr = (void __iomem *)((uintptr_t)pp->va_cfg0_base +
+					 (busnr_ecam << 20) +
+					 PCIE_ECAM_DEVFN(devfn));
+
+	if (busnr_reg != target_bus_cfg->reg_val) {
+		dev_dbg(pcie->pci->dev, "Changing target bus busnum val from 0x%x to 0x%x\n",
+			target_bus_cfg->reg_val, busnr_reg);
+		target_bus_cfg->reg_val = busnr_reg;
+		al_pcie_target_bus_set(pcie,
+				       target_bus_cfg->reg_val,
+				       target_bus_cfg->reg_mask);
+	}
+
+	return pci_base_addr;
+}
+
+static int al_pcie_rd_other_conf(struct pcie_port *pp, struct pci_bus *bus,
+				 unsigned int devfn, int where, int size,
+				 u32 *val)
+{
+	struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
+	struct al_pcie *pcie = to_al_pcie(pci);
+	unsigned int busnr = bus->number;
+	void __iomem *pci_addr;
+	int rc;
+
+	pci_addr = al_pcie_conf_addr_map(pcie, busnr, devfn);
+
+	rc = dw_pcie_read(pci_addr + where, size, val);
+
+	dev_dbg(pci->dev, "%d-byte config read from %04x:%02x:%02x.%d offset 0x%x (pci_addr: 0x%px) - val:0x%x\n",
+		size, pci_domain_nr(bus), bus->number,
+		PCI_SLOT(devfn), PCI_FUNC(devfn), where,
+		(pci_addr + where), *val);
+
+	return rc;
+}
+
+static int al_pcie_wr_other_conf(struct pcie_port *pp, struct pci_bus *bus,
+				 unsigned int devfn, int where, int size,
+				 u32 val)
+{
+	struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
+	struct al_pcie *pcie = to_al_pcie(pci);
+	unsigned int busnr = bus->number;
+	void __iomem *pci_addr;
+	int rc;
+
+	pci_addr = al_pcie_conf_addr_map(pcie, busnr, devfn);
+
+	rc = dw_pcie_write(pci_addr + where, size, val);
+
+	dev_err(pci->dev, "%d-byte config write to %04x:%02x:%02x.%d offset 0x%x (pci_addr: 0x%px) - val:0x%x\n",
+		size, pci_domain_nr(bus), bus->number,
+		PCI_SLOT(devfn), PCI_FUNC(devfn), where,
+		(pci_addr + where), val);
+
+	return rc;
+}
+
+static void al_pcie_config_prepare(struct al_pcie *pcie)
+{
+	struct al_pcie_target_bus_cfg *target_bus_cfg;
+	struct pcie_port *pp = &pcie->pci->pp;
+	unsigned int ecam_bus_mask;
+	u32 cfg_control_offset;
+	u8 subordinate_bus;
+	u8 secondary_bus;
+	u32 cfg_control;
+	u32 reg;
+
+	target_bus_cfg = &pcie->target_bus_cfg;
+
+	ecam_bus_mask = (pcie->ecam_size >> 20) - 1;
+	if (ecam_bus_mask > 255) {
+		dev_warn(pcie->dev, "ECAM window size is larger than 256MB. Cutting off at 256\n");
+		ecam_bus_mask = 255;
+	}
+
+	/* This portion is taken from the transaction address */
+	target_bus_cfg->ecam_mask = ecam_bus_mask;
+	/* This portion is taken from the cfg_target_bus reg */
+	target_bus_cfg->reg_mask = ~target_bus_cfg->ecam_mask;
+	target_bus_cfg->reg_val = pp->busn->start & target_bus_cfg->reg_mask;
+
+	al_pcie_target_bus_set(pcie, target_bus_cfg->reg_val,
+			       target_bus_cfg->reg_mask);
+
+	secondary_bus = pp->busn->start + 1;
+	subordinate_bus = pp->busn->end;
+
+	/* Set the valid values of secondary and subordinate buses */
+	cfg_control_offset = AXI_BASE_OFFSET + pcie->reg_offsets.ob_ctrl +
+			     CFG_CONTROL;
+
+	cfg_control = al_pcie_controller_readl(pcie, cfg_control_offset);
+
+	reg = cfg_control &
+	      ~(CFG_CONTROL_SEC_BUS_MASK | CFG_CONTROL_SUBBUS_MASK);
+
+	reg |= FIELD_PREP(CFG_CONTROL_SUBBUS_MASK, subordinate_bus) |
+	       FIELD_PREP(CFG_CONTROL_SEC_BUS_MASK, secondary_bus);
+
+	al_pcie_controller_writel(pcie, cfg_control_offset, reg);
+}
+
+static int al_pcie_host_init(struct pcie_port *pp)
+{
+	struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
+	struct al_pcie *pcie = to_al_pcie(pci);
+	int link_up;
+	int rc;
+
+	rc = al_pcie_rev_id_get(pcie, &pcie->controller_rev_id);
+	if (rc)
+		return rc;
+
+	rc = al_pcie_reg_offsets_set(pcie);
+	if (rc)
+		return rc;
+
+	al_pcie_config_prepare(pcie);
+
+	return 0;
+}
+
+static const struct dw_pcie_host_ops al_pcie_host_ops = {
+	.rd_other_conf = al_pcie_rd_other_conf,
+	.wr_other_conf = al_pcie_wr_other_conf,
+	.host_init = al_pcie_host_init,
+};
+
+static int al_add_pcie_port(struct pcie_port *pp,
+			    struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	int ret;
+
+	pp->ops = &al_pcie_host_ops;
+
+	ret = dw_pcie_host_init(pp);
+	if (ret) {
+		dev_err(dev, "failed to initialize host\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+static const struct dw_pcie_ops dw_pcie_ops = {
+};
+
+static int al_pcie_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct resource *controller_res;
+	struct resource *ecam_res;
+	struct resource *dbi_res;
+	struct al_pcie *al_pcie;
+	struct dw_pcie *pci;
+	int ret;
+
+	al_pcie = devm_kzalloc(dev, sizeof(*al_pcie), GFP_KERNEL);
+	if (!al_pcie)
+		return -ENOMEM;
+
+	pci = devm_kzalloc(dev, sizeof(*pci), GFP_KERNEL);
+	if (!pci)
+		return -ENOMEM;
+
+	pci->dev = dev;
+	pci->ops = &dw_pcie_ops;
+
+	al_pcie->pci = pci;
+	al_pcie->dev = dev;
+
+	dbi_res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "dbi");
+	pci->dbi_base = devm_pci_remap_cfg_resource(dev, dbi_res);
+	if (IS_ERR(pci->dbi_base)) {
+		dev_err(dev, "couldn't remap dbi base %pR\n", dbi_res);
+		return PTR_ERR(pci->dbi_base);
+	}
+
+	ecam_res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "config");
+	if (!ecam_res) {
+		dev_err(dev, "couldn't find 'config' reg in DT\n");
+		return -ENOENT;
+	}
+	al_pcie->ecam_size = resource_size(ecam_res);
+
+	controller_res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
+						      "controller");
+	al_pcie->controller_base = devm_ioremap_resource(dev, controller_res);
+	if (IS_ERR(al_pcie->controller_base)) {
+		dev_err(dev, "couldn't remap controller base %pR\n",
+			controller_res);
+		return PTR_ERR(al_pcie->controller_base);
+	}
+
+	dev_dbg(dev, "From DT: dbi_base: %pR, controller_base: %pR\n",
+		dbi_res, controller_res);
+
+	platform_set_drvdata(pdev, al_pcie);
+
+	ret = al_add_pcie_port(&pci->pp, pdev);
+
+	return ret;
+}
+
+static const struct of_device_id al_pcie_of_match[] = {
+	{ .compatible = "amazon,al-pcie",
+	},
+	{},
+};
+
+static struct platform_driver al_pcie_driver = {
+	.driver = {
+		.name	= "al-pcie",
+		.of_match_table = al_pcie_of_match,
+		.suppress_bind_attrs = true,
+	},
+	.probe = al_pcie_probe,
+};
+builtin_platform_driver(al_pcie_driver);
+
+#endif /* CONFIG_PCIE_AL*/
-- 
2.17.1


  parent reply	other threads:[~2019-07-23  9:27 UTC|newest]

Thread overview: 27+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-07-23  9:25 [PATCH v3 0/8] Amazon's Annapurna Labs DT-based PCIe host controller driver Jonathan Chocron
2019-07-23  9:25 ` [PATCH v3 1/8] PCI: Add Amazon's Annapurna Labs vendor ID Jonathan Chocron
2019-08-19 17:51   ` Andrew Murray
2019-07-23  9:25 ` [PATCH v3 2/8] PCI: Add ACS quirk for Amazon Annapurna Labs root ports Jonathan Chocron
2019-07-23  9:25 ` [PATCH v3 3/8] PCI/VPD: Add VPD release quirk for Amazon's Annapurna Labs Root Port Jonathan Chocron
2019-07-23  9:25 ` [PATCH v3 4/8] PCI: Add quirk to disable MSI-X support " Jonathan Chocron
2019-08-19 18:23   ` Andrew Murray
2019-08-20 14:52     ` Chocron, Jonathan
2019-08-20 15:25       ` Andrew Murray
2019-08-20 17:06         ` Chocron, Jonathan
2019-08-20 19:54           ` Andrew Murray
2019-08-21 10:30             ` Chocron, Jonathan
2019-07-23  9:27 ` [PATCH v3 5/8] dt-bindings: PCI: Add Amazon's Annapurna Labs PCIe host bridge binding Jonathan Chocron
2019-08-13 15:30   ` Rob Herring
2019-08-13 16:48     ` Chocron, Jonathan
2019-08-13 20:46       ` Rob Herring
2019-08-19 16:15         ` Chocron, Jonathan
2019-07-23  9:27 ` Jonathan Chocron [this message]
2019-07-23  9:40   ` [PATCH v3 6/8] PCI: al: Add support for DW based driver type Gustavo Pimentel
2019-08-12 17:03   ` Lorenzo Pieralisi
2019-08-14 11:39     ` Chocron, Jonathan
2019-07-23  9:27 ` [PATCH v3 7/8] PCI: dw: Add validation that PCIe core is set to correct mode Jonathan Chocron
2019-07-23  9:27 ` [PATCH v3 8/8] PCI: dw: Add support for PCI_PROBE_ONLY/PCI_REASSIGN_ALL_BUS flags Jonathan Chocron
2019-08-07 16:36   ` Lorenzo Pieralisi
2019-08-08  9:30     ` Chocron, Jonathan
2019-08-08 10:58       ` Lorenzo Pieralisi
2019-08-12 18:05         ` Chocron, Jonathan

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20190723092711.11786-2-jonnyc@amazon.com \
    --to=jonnyc@amazon.com \
    --cc=alisaidi@amazon.com \
    --cc=barakw@amazon.com \
    --cc=benh@kernel.crashing.org \
    --cc=bhelgaas@google.com \
    --cc=devicetree@vger.kernel.org \
    --cc=dwmw@amazon.co.uk \
    --cc=gustavo.pimentel@synopsys.com \
    --cc=hanochu@amazon.com \
    --cc=hhhawa@amazon.com \
    --cc=jingoohan1@gmail.com \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-pci@vger.kernel.org \
    --cc=lorenzo.pieralisi@arm.com \
    --cc=mark.rutland@arm.com \
    --cc=robh+dt@kernel.org \
    --cc=ronenk@amazon.com \
    --cc=talel@amazon.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).