From: Vinod Koul <vkoul@kernel.org>
To: Andy Gross <agross@kernel.org>
Cc: linux-arm-msm@vger.kernel.org,
Bjorn Andersson <bjorn.andersson@linaro.org>,
Vinod Koul <vkoul@kernel.org>, Rob Herring <robh+dt@kernel.org>,
Mark Rutland <mark.rutland@arm.com>,
Stephen Boyd <sboyd@kernel.org>,
Sibi Sankar <sibis@codeaurora.org>,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org
Subject: [PATCH v2 1/8] arm64: dts: qcom: sm8150: add base dts file
Date: Tue, 20 Aug 2019 12:12:09 +0530 [thread overview]
Message-ID: <20190820064216.8629-2-vkoul@kernel.org> (raw)
In-Reply-To: <20190820064216.8629-1-vkoul@kernel.org>
This add base DTS file with cpu, psci, firmware, clock, tlmm and
spmi nodes which enables boot to console
Signed-off-by: Vinod Koul <vkoul@kernel.org>
---
arch/arm64/boot/dts/qcom/sm8150.dtsi | 305 +++++++++++++++++++++++++++
1 file changed, 305 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/sm8150.dtsi
diff --git a/arch/arm64/boot/dts/qcom/sm8150.dtsi b/arch/arm64/boot/dts/qcom/sm8150.dtsi
new file mode 100644
index 000000000000..d9dc95f851b7
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sm8150.dtsi
@@ -0,0 +1,305 @@
+// SPDX-License-Identifier: BSD-3-Clause
+// Copyright (c) 2017-2019, The Linux Foundation. All rights reserved.
+// Copyright (c) 2019, Linaro Limited
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/soc/qcom,rpmh-rsc.h>
+#include <dt-bindings/clock/qcom,rpmh.h>
+
+/ {
+ interrupt-parent = <&intc>;
+
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ chosen { };
+
+ clocks {
+ xo_board: xo-board {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <38400000>;
+ clock-output-names = "xo_board";
+ };
+
+ sleep_clk: sleep-clk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32764>;
+ clock-output-names = "sleep_clk";
+ };
+ };
+
+ cpus {
+ #address-cells = <2>;
+ #size-cells = <0>;
+
+ CPU0: cpu@0 {
+ device_type = "cpu";
+ compatible = "qcom,kryo485";
+ reg = <0x0 0x0>;
+ enable-method = "psci";
+ next-level-cache = <&L2_0>;
+ L2_0: l2-cache {
+ compatible = "cache";
+ next-level-cache = <&L3_0>;
+ L3_0: l3-cache {
+ compatible = "cache";
+ };
+ };
+ };
+
+ CPU1: cpu@100 {
+ device_type = "cpu";
+ compatible = "qcom,kryo485";
+ reg = <0x0 0x100>;
+ enable-method = "psci";
+ next-level-cache = <&L2_100>;
+ L2_100: l2-cache {
+ compatible = "cache";
+ next-level-cache = <&L3_0>;
+ };
+
+ };
+
+ CPU2: cpu@200 {
+ device_type = "cpu";
+ compatible = "qcom,kryo485";
+ reg = <0x0 0x200>;
+ enable-method = "psci";
+ next-level-cache = <&L2_200>;
+ L2_200: l2-cache {
+ compatible = "cache";
+ next-level-cache = <&L3_0>;
+ };
+ };
+
+ CPU3: cpu@300 {
+ device_type = "cpu";
+ compatible = "qcom,kryo485";
+ reg = <0x0 0x300>;
+ enable-method = "psci";
+ next-level-cache = <&L2_300>;
+ L2_300: l2-cache {
+ compatible = "cache";
+ next-level-cache = <&L3_0>;
+ };
+ };
+
+ CPU4: cpu@400 {
+ device_type = "cpu";
+ compatible = "qcom,kryo485";
+ reg = <0x0 0x400>;
+ enable-method = "psci";
+ next-level-cache = <&L2_400>;
+ L2_400: l2-cache {
+ compatible = "cache";
+ next-level-cache = <&L3_0>;
+ };
+ };
+
+ CPU5: cpu@500 {
+ device_type = "cpu";
+ compatible = "qcom,kryo485";
+ reg = <0x0 0x500>;
+ enable-method = "psci";
+ next-level-cache = <&L2_500>;
+ L2_500: l2-cache {
+ compatible = "cache";
+ next-level-cache = <&L3_0>;
+ };
+ };
+
+ CPU6: cpu@600 {
+ device_type = "cpu";
+ compatible = "qcom,kryo485";
+ reg = <0x0 0x600>;
+ enable-method = "psci";
+ next-level-cache = <&L2_600>;
+ L2_600: l2-cache {
+ compatible = "cache";
+ next-level-cache = <&L3_0>;
+ };
+ };
+
+ CPU7: cpu@700 {
+ device_type = "cpu";
+ compatible = "qcom,kryo485";
+ reg = <0x0 0x700>;
+ enable-method = "psci";
+ next-level-cache = <&L2_700>;
+ L2_700: l2-cache {
+ compatible = "cache";
+ next-level-cache = <&L3_0>;
+ };
+ };
+ };
+
+ firmware {
+ scm: scm {
+ compatible = "qcom,scm-sm8150", "qcom,scm";
+ #reset-cells = <1>;
+ };
+ };
+
+ memory@80000000 {
+ device_type = "memory";
+ /* We expect the bootloader to fill in the size */
+ reg = <0 0x80000000 0 0>;
+ };
+
+ psci {
+ compatible = "arm,psci-1.0";
+ method = "smc";
+ };
+
+ soc: soc@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0 0 0xffffffff>;
+ compatible = "simple-bus";
+
+ gcc: clock-controller@100000 {
+ compatible = "qcom,gcc-sm8150";
+ reg = <0x00100000 0x1f0000>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ #power-domain-cells = <1>;
+ clock-names = "bi_tcxo",
+ "sleep_clk";
+ clocks = <&rpmhcc RPMH_CXO_CLK>,
+ <&sleep_clk>;
+ };
+
+ qupv3_id_1: geniqup@ac0000 {
+ compatible = "qcom,geni-se-qup";
+ reg = <0x00ac0000 0x6000>;
+ clock-names = "m-ahb", "s-ahb";
+ clocks = <&gcc 123>,
+ <&gcc 124>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ status = "disabled";
+
+ uart2: serial@a90000 {
+ compatible = "qcom,geni-debug-uart";
+ reg = <0x00a90000 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc 105>;
+ interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+ };
+
+ tlmm: pinctrl@3100000 {
+ compatible = "qcom,sm8150-pinctrl";
+ reg = <0x03100000 0x300000>,
+ <0x03500000 0x300000>,
+ <0x03900000 0x300000>,
+ <0x03d00000 0x300000>;
+ reg-names = "west", "east", "north", "south";
+ interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-ranges = <&tlmm 0 0 175>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ intc: interrupt-controller@17a00000 {
+ compatible = "arm,gic-v3";
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ reg = <0x17a00000 0x10000>, /* GICD */
+ <0x17a60000 0x100000>; /* GICR * 8 */
+ interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ timer@17c20000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ compatible = "arm,armv7-timer-mem";
+ reg = <0x17c20000 0x1000>;
+ clock-frequency = <19200000>;
+
+ frame@17c21000{
+ frame-number = <0>;
+ interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0x17c21000 0x1000>,
+ <0x17c22000 0x1000>;
+ };
+
+ frame@17c23000 {
+ frame-number = <1>;
+ interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0x17c23000 0x1000>;
+ status = "disabled";
+ };
+
+ frame@17c25000 {
+ frame-number = <2>;
+ interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0x17c25000 0x1000>;
+ status = "disabled";
+ };
+
+ frame@17c27000 {
+ frame-number = <3>;
+ interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0x17c26000 0x1000>;
+ status = "disabled";
+ };
+
+ frame@17c29000 {
+ frame-number = <4>;
+ interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0x17c29000 0x1000>;
+ status = "disabled";
+ };
+
+ frame@17c2b000 {
+ frame-number = <5>;
+ interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0x17c2b000 0x1000>;
+ status = "disabled";
+ };
+
+ frame@17c2d000 {
+ frame-number = <6>;
+ interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0x17c2d000 0x1000>;
+ status = "disabled";
+ };
+ };
+
+ spmi_bus: spmi@c440000 {
+ compatible = "qcom,spmi-pmic-arb";
+ reg = <0x0c440000 0x0001100>,
+ <0x0c600000 0x2000000>,
+ <0x0e600000 0x0100000>,
+ <0x0e700000 0x00a0000>,
+ <0x0c40a000 0x0026000>;
+ reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
+ interrupt-names = "periph_irq";
+ interrupts = <GIC_SPI 481 IRQ_TYPE_LEVEL_HIGH>;
+ qcom,ee = <0>;
+ qcom,channel = <0>;
+ #address-cells = <2>;
+ #size-cells = <0>;
+ interrupt-controller;
+ #interrupt-cells = <4>;
+ cell-index = <0>;
+ };
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <GIC_PPI 1 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_PPI 2 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_PPI 3 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_PPI 0 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
--
2.20.1
next prev parent reply other threads:[~2019-08-20 6:44 UTC|newest]
Thread overview: 24+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-08-20 6:42 [PATCH v2 0/8] arm64: dts: qcom: sm8150: Add SM8150 DTS Vinod Koul
2019-08-20 6:42 ` Vinod Koul [this message]
2019-08-20 12:27 ` [PATCH v2 1/8] arm64: dts: qcom: sm8150: add base dts file Niklas Cassel
2019-08-20 12:33 ` Vinod Koul
2019-08-20 13:33 ` Amit Kucheria
2019-08-20 16:37 ` Vinod Koul
2019-08-20 6:42 ` [PATCH v2 2/8] arm64: dts: qcom: pm8150: Add Base DTS file Vinod Koul
2019-08-20 12:27 ` Niklas Cassel
2019-08-20 12:34 ` Vinod Koul
2019-08-20 6:42 ` [PATCH v2 3/8] arm64: dts: qcom: pm8150b: " Vinod Koul
2019-08-20 12:27 ` Niklas Cassel
2019-08-20 12:35 ` Vinod Koul
2019-08-20 6:42 ` [PATCH v2 4/8] arm64: dts: qcom: pm8150l: " Vinod Koul
2019-08-20 6:42 ` [PATCH v2 5/8] arm64: dts: qcom: sm8150-mtp: add base dts file Vinod Koul
2019-08-20 12:26 ` Niklas Cassel
2019-08-20 12:36 ` Vinod Koul
2019-08-20 6:42 ` [PATCH v2 6/8] arm64: dts: qcom: sm8150-mtp: Add regulators Vinod Koul
2019-08-20 12:26 ` Niklas Cassel
2019-08-20 12:37 ` Vinod Koul
2019-08-20 6:42 ` [PATCH v2 7/8] arm64: dts: qcom: sm8150: Add reserved-memory regions Vinod Koul
2019-08-20 12:24 ` Niklas Cassel
2019-08-20 6:42 ` [PATCH v2 8/8] arm64: dts: qcom: sm8150: Add apps shared nodes Vinod Koul
2019-08-20 12:28 ` [PATCH v2 0/8] arm64: dts: qcom: sm8150: Add SM8150 DTS Niklas Cassel
2019-08-20 12:39 ` Vinod Koul
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190820064216.8629-2-vkoul@kernel.org \
--to=vkoul@kernel.org \
--cc=agross@kernel.org \
--cc=bjorn.andersson@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=robh+dt@kernel.org \
--cc=sboyd@kernel.org \
--cc=sibis@codeaurora.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).