From: Vinod Koul <vkoul@kernel.org>
To: Andy Gross <agross@kernel.org>
Cc: linux-arm-msm@vger.kernel.org,
Bjorn Andersson <bjorn.andersson@linaro.org>,
Vinod Koul <vkoul@kernel.org>, Rob Herring <robh+dt@kernel.org>,
Mark Rutland <mark.rutland@arm.com>,
Stephen Boyd <sboyd@kernel.org>,
Sibi Sankar <sibis@codeaurora.org>,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
Niklas Cassel <niklas.cassel@linaro.org>
Subject: [PATCH v4 4/8] arm64: dts: qcom: pm8150l: Add base dts file
Date: Thu, 22 Aug 2019 00:12:35 +0530 [thread overview]
Message-ID: <20190821184239.12364-5-vkoul@kernel.org> (raw)
In-Reply-To: <20190821184239.12364-1-vkoul@kernel.org>
PMIC pm8150l is a slave pmic and this adds base DTS file for pm8150l
with power-on, adc and gpio nodes
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
---
arch/arm64/boot/dts/qcom/pm8150l.dtsi | 80 +++++++++++++++++++++++++++
1 file changed, 80 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/pm8150l.dtsi
diff --git a/arch/arm64/boot/dts/qcom/pm8150l.dtsi b/arch/arm64/boot/dts/qcom/pm8150l.dtsi
new file mode 100644
index 000000000000..eb0e9a090e42
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/pm8150l.dtsi
@@ -0,0 +1,80 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2017-2019, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2019, Linaro Limited
+ */
+
+#include <dt-bindings/iio/qcom,spmi-vadc.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+
+&spmi_bus {
+ pmic@4 {
+ compatible = "qcom,pm8150l", "qcom,spmi-pmic";
+ reg = <0x4 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ power-on@800 {
+ compatible = "qcom,pm8916-pon";
+ reg = <0x0800>;
+
+ status = "disabled";
+ };
+
+ adc@3100 {
+ compatible = "qcom,spmi-adc5";
+ reg = <0x3100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #io-channel-cells = <1>;
+ interrupts = <0x4 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
+
+ status = "disabled";
+
+ ref-gnd@0 {
+ reg = <ADC5_REF_GND>;
+ qcom,pre-scaling = <1 1>;
+ label = "ref_gnd";
+ };
+
+ vref-1p25@1 {
+ reg = <ADC5_1P25VREF>;
+ qcom,pre-scaling = <1 1>;
+ label = "vref_1p25";
+ };
+
+ die-temp@6 {
+ reg = <ADC5_DIE_TEMP>;
+ qcom,pre-scaling = <1 1>;
+ label = "die_temp";
+ };
+ };
+
+ pm8150l_gpios: gpio@c000 {
+ compatible = "qcom,pm8150l-gpio";
+ reg = <0xc000>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupts = <0x4 0xc0 0x0 IRQ_TYPE_NONE>,
+ <0x4 0xc1 0x0 IRQ_TYPE_NONE>,
+ <0x4 0xc2 0x0 IRQ_TYPE_NONE>,
+ <0x4 0xc3 0x0 IRQ_TYPE_NONE>,
+ <0x4 0xc4 0x0 IRQ_TYPE_NONE>,
+ <0x4 0xc5 0x0 IRQ_TYPE_NONE>,
+ <0x4 0xc6 0x0 IRQ_TYPE_NONE>,
+ <0x4 0xc7 0x0 IRQ_TYPE_NONE>,
+ <0x4 0xc8 0x0 IRQ_TYPE_NONE>,
+ <0x4 0xc9 0x0 IRQ_TYPE_NONE>,
+ <0x4 0xca 0x0 IRQ_TYPE_NONE>,
+ <0x4 0xcb 0x0 IRQ_TYPE_NONE>;
+ };
+ };
+
+ pmic@5 {
+ compatible = "qcom,pm8150l", "qcom,spmi-pmic";
+ reg = <0x5 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+};
--
2.20.1
next prev parent reply other threads:[~2019-08-21 18:44 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-08-21 18:42 [PATCH v4 0/8] arm64: dts: qcom: sm8150: Add SM8150 DTS Vinod Koul
2019-08-21 18:42 ` [PATCH v4 1/8] arm64: dts: qcom: sm8150: Add base dts file Vinod Koul
2019-08-21 19:07 ` Amit Kucheria
2019-08-21 18:42 ` [PATCH v4 2/8] arm64: dts: qcom: pm8150: " Vinod Koul
2019-08-21 18:42 ` [PATCH v4 3/8] arm64: dts: qcom: pm8150b: " Vinod Koul
2019-08-21 18:42 ` Vinod Koul [this message]
2019-08-21 18:42 ` [PATCH v4 5/8] arm64: dts: qcom: sm8150-mtp: " Vinod Koul
2019-08-21 18:42 ` [PATCH v4 6/8] arm64: dts: qcom: sm8150-mtp: Add regulators Vinod Koul
2019-08-23 6:05 ` kgunda
2019-08-27 15:23 ` kgunda
2019-08-21 18:42 ` [PATCH v4 7/8] arm64: dts: qcom: sm8150: Add reserved-memory regions Vinod Koul
2019-08-21 18:42 ` [PATCH v4 8/8] arm64: dts: qcom: sm8150: Add apps shared nodes Vinod Koul
2019-08-21 23:04 ` [PATCH v4 0/8] arm64: dts: qcom: sm8150: Add SM8150 DTS Bjorn Andersson
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190821184239.12364-5-vkoul@kernel.org \
--to=vkoul@kernel.org \
--cc=agross@kernel.org \
--cc=bjorn.andersson@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=niklas.cassel@linaro.org \
--cc=robh+dt@kernel.org \
--cc=sboyd@kernel.org \
--cc=sibis@codeaurora.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).