From: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
To: Lee Jones <lee.jones@linaro.org>,
Rob Herring <robh+dt@kernel.org>, Mark Brown <broonie@kernel.org>,
Matthias Brugger <matthias.bgg@gmail.com>,
Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Mark Rutland <mark.rutland@arm.com>,
Liam Girdwood <lgirdwood@gmail.com>,
Eddie Huang <eddie.huang@mediatek.com>,
Sean Wang <sean.wang@mediatek.com>,
Alessandro Zummo <a.zummo@towertech.it>,
Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>,
Kate Stewart <kstewart@linuxfoundation.org>,
Greg Kroah-Hartman <gregkh@linuxfoundation.org>,
Thomas Gleixner <tglx@linutronix.de>,
Richard Fontana <rfontana@redhat.com>,
<devicetree@vger.kernel.org>,
<linux-arm-kernel@lists.infradead.org>,
<linux-mediatek@lists.infradead.org>,
<linux-kernel@vger.kernel.org>, <linux-rtc@vger.kernel.org>,
<srv_heupstream@mediatek.com>
Subject: [PATCH v5 07/10] regulator: mt6358: Add support for MT6358 regulator
Date: Fri, 23 Aug 2019 11:45:28 +0800 [thread overview]
Message-ID: <1566531931-9772-8-git-send-email-hsin-hsiung.wang@mediatek.com> (raw)
In-Reply-To: <1566531931-9772-1-git-send-email-hsin-hsiung.wang@mediatek.com>
The MT6358 is a regulator found on boards based on MediaTek MT8183 and
probably other SoCs. It is a so called pmic and connects as a slave to
SoC using SPI, wrapped inside the pmic-wrapper.
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
---
drivers/regulator/Kconfig | 9 +
drivers/regulator/Makefile | 1 +
drivers/regulator/mt6358-regulator.c | 549 +++++++++++++++++++++++++++++
include/linux/regulator/mt6358-regulator.h | 56 +++
4 files changed, 615 insertions(+)
create mode 100644 drivers/regulator/mt6358-regulator.c
create mode 100644 include/linux/regulator/mt6358-regulator.h
diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index b57093d..1337623 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -618,6 +618,15 @@ config REGULATOR_MT6323
This driver supports the control of different power rails of device
through regulator interface.
+config REGULATOR_MT6358
+ tristate "MediaTek MT6358 PMIC"
+ depends on MFD_MT6397
+ help
+ Say y here to select this option to enable the power regulator of
+ MediaTek MT6358 PMIC.
+ This driver supports the control of different power rails of device
+ through regulator interface.
+
config REGULATOR_MT6380
tristate "MediaTek MT6380 PMIC"
depends on MTK_PMIC_WRAP
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index eef73b5..9fcc40e 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -79,6 +79,7 @@ obj-$(CONFIG_REGULATOR_MC13XXX_CORE) += mc13xxx-regulator-core.o
obj-$(CONFIG_REGULATOR_MCP16502) += mcp16502.o
obj-$(CONFIG_REGULATOR_MT6311) += mt6311-regulator.o
obj-$(CONFIG_REGULATOR_MT6323) += mt6323-regulator.o
+obj-$(CONFIG_REGULATOR_MT6358) += mt6358-regulator.o
obj-$(CONFIG_REGULATOR_MT6380) += mt6380-regulator.o
obj-$(CONFIG_REGULATOR_MT6397) += mt6397-regulator.o
obj-$(CONFIG_REGULATOR_QCOM_RPM) += qcom_rpm-regulator.o
diff --git a/drivers/regulator/mt6358-regulator.c b/drivers/regulator/mt6358-regulator.c
new file mode 100644
index 0000000..ba42682
--- /dev/null
+++ b/drivers/regulator/mt6358-regulator.c
@@ -0,0 +1,549 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (c) 2019 MediaTek Inc.
+
+#include <linux/mfd/mt6358/registers.h>
+#include <linux/mfd/mt6397/core.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/machine.h>
+#include <linux/regulator/mt6358-regulator.h>
+#include <linux/regulator/of_regulator.h>
+
+#define MT6358_BUCK_MODE_AUTO 0
+#define MT6358_BUCK_MODE_FORCE_PWM 1
+
+/*
+ * MT6358 regulators' information
+ *
+ * @desc: standard fields of regulator description.
+ * @qi: Mask for query enable signal status of regulators
+ */
+struct mt6358_regulator_info {
+ struct regulator_desc desc;
+ u32 status_reg;
+ u32 qi;
+ const u32 *index_table;
+ unsigned int n_table;
+ u32 vsel_shift;
+ u32 da_vsel_reg;
+ u32 da_vsel_mask;
+ u32 da_vsel_shift;
+ u32 modeset_reg;
+ u32 modeset_mask;
+ u32 modeset_shift;
+};
+
+#define MT6358_BUCK(match, vreg, min, max, step, \
+ volt_ranges, vosel_mask, _da_vsel_reg, _da_vsel_mask, \
+ _da_vsel_shift, _modeset_reg, _modeset_shift) \
+[MT6358_ID_##vreg] = { \
+ .desc = { \
+ .name = #vreg, \
+ .of_match = of_match_ptr(match), \
+ .ops = &mt6358_volt_range_ops, \
+ .type = REGULATOR_VOLTAGE, \
+ .id = MT6358_ID_##vreg, \
+ .owner = THIS_MODULE, \
+ .n_voltages = ((max) - (min)) / (step) + 1, \
+ .linear_ranges = volt_ranges, \
+ .n_linear_ranges = ARRAY_SIZE(volt_ranges), \
+ .vsel_reg = MT6358_BUCK_##vreg##_ELR0, \
+ .vsel_mask = vosel_mask, \
+ .enable_reg = MT6358_BUCK_##vreg##_CON0, \
+ .enable_mask = BIT(0), \
+ .of_map_mode = mt6358_map_mode, \
+ }, \
+ .status_reg = MT6358_BUCK_##vreg##_DBG1, \
+ .qi = BIT(0), \
+ .da_vsel_reg = _da_vsel_reg, \
+ .da_vsel_mask = _da_vsel_mask, \
+ .da_vsel_shift = _da_vsel_shift, \
+ .modeset_reg = _modeset_reg, \
+ .modeset_mask = BIT(_modeset_shift), \
+ .modeset_shift = _modeset_shift \
+}
+
+#define MT6358_LDO(match, vreg, ldo_volt_table, \
+ ldo_index_table, enreg, enbit, vosel, \
+ vosel_mask, vosel_shift) \
+[MT6358_ID_##vreg] = { \
+ .desc = { \
+ .name = #vreg, \
+ .of_match = of_match_ptr(match), \
+ .ops = &mt6358_volt_table_ops, \
+ .type = REGULATOR_VOLTAGE, \
+ .id = MT6358_ID_##vreg, \
+ .owner = THIS_MODULE, \
+ .n_voltages = ARRAY_SIZE(ldo_volt_table), \
+ .volt_table = ldo_volt_table, \
+ .vsel_reg = vosel, \
+ .vsel_mask = vosel_mask, \
+ .enable_reg = enreg, \
+ .enable_mask = BIT(enbit), \
+ }, \
+ .status_reg = MT6358_LDO_##vreg##_CON1, \
+ .qi = BIT(15), \
+ .index_table = ldo_index_table, \
+ .n_table = ARRAY_SIZE(ldo_index_table), \
+ .vsel_shift = vosel_shift, \
+}
+
+#define MT6358_LDO1(match, vreg, min, max, step, \
+ volt_ranges, _da_vsel_reg, _da_vsel_mask, \
+ _da_vsel_shift, vosel, vosel_mask) \
+[MT6358_ID_##vreg] = { \
+ .desc = { \
+ .name = #vreg, \
+ .of_match = of_match_ptr(match), \
+ .ops = &mt6358_volt_range_ops, \
+ .type = REGULATOR_VOLTAGE, \
+ .id = MT6358_ID_##vreg, \
+ .owner = THIS_MODULE, \
+ .n_voltages = ((max) - (min)) / (step) + 1, \
+ .linear_ranges = volt_ranges, \
+ .n_linear_ranges = ARRAY_SIZE(volt_ranges), \
+ .vsel_reg = vosel, \
+ .vsel_mask = vosel_mask, \
+ .enable_reg = MT6358_LDO_##vreg##_CON0, \
+ .enable_mask = BIT(0), \
+ }, \
+ .da_vsel_reg = _da_vsel_reg, \
+ .da_vsel_mask = _da_vsel_mask, \
+ .da_vsel_shift = _da_vsel_shift, \
+ .status_reg = MT6358_LDO_##vreg##_DBG1, \
+ .qi = BIT(0), \
+}
+
+#define MT6358_REG_FIXED(match, vreg, \
+ enreg, enbit, volt) \
+[MT6358_ID_##vreg] = { \
+ .desc = { \
+ .name = #vreg, \
+ .of_match = of_match_ptr(match), \
+ .ops = &mt6358_volt_fixed_ops, \
+ .type = REGULATOR_VOLTAGE, \
+ .id = MT6358_ID_##vreg, \
+ .owner = THIS_MODULE, \
+ .n_voltages = 1, \
+ .enable_reg = enreg, \
+ .enable_mask = BIT(enbit), \
+ .min_uV = volt, \
+ }, \
+ .status_reg = MT6358_LDO_##vreg##_CON1, \
+ .qi = BIT(15), \
+}
+
+static const struct regulator_linear_range buck_volt_range1[] = {
+ REGULATOR_LINEAR_RANGE(500000, 0, 0x7f, 6250),
+};
+
+static const struct regulator_linear_range buck_volt_range2[] = {
+ REGULATOR_LINEAR_RANGE(500000, 0, 0x7f, 12500),
+};
+
+static const struct regulator_linear_range buck_volt_range3[] = {
+ REGULATOR_LINEAR_RANGE(500000, 0, 0x3f, 50000),
+};
+
+static const struct regulator_linear_range buck_volt_range4[] = {
+ REGULATOR_LINEAR_RANGE(1000000, 0, 0x7f, 12500),
+};
+
+static const u32 vdram2_voltages[] = {
+ 600000, 1800000,
+};
+
+static const u32 vsim_voltages[] = {
+ 1700000, 1800000, 2700000, 3000000, 3100000,
+};
+
+static const u32 vibr_voltages[] = {
+ 1200000, 1300000, 1500000, 1800000,
+ 2000000, 2800000, 3000000, 3300000,
+};
+
+static const u32 vusb_voltages[] = {
+ 3000000, 3100000,
+};
+
+static const u32 vcamd_voltages[] = {
+ 900000, 1000000, 1100000, 1200000,
+ 1300000, 1500000, 1800000,
+};
+
+static const u32 vefuse_voltages[] = {
+ 1700000, 1800000, 1900000,
+};
+
+static const u32 vmch_vemc_voltages[] = {
+ 2900000, 3000000, 3300000,
+};
+
+static const u32 vcama_voltages[] = {
+ 1800000, 2500000, 2700000,
+ 2800000, 2900000, 3000000,
+};
+
+static const u32 vcn33_bt_wifi_voltages[] = {
+ 3300000, 3400000, 3500000,
+};
+
+static const u32 vmc_voltages[] = {
+ 1800000, 2900000, 3000000, 3300000,
+};
+
+static const u32 vldo28_voltages[] = {
+ 2800000, 3000000,
+};
+
+static const u32 vdram2_idx[] = {
+ 0, 12,
+};
+
+static const u32 vsim_idx[] = {
+ 3, 4, 8, 11, 12,
+};
+
+static const u32 vibr_idx[] = {
+ 0, 1, 2, 4, 5, 9, 11, 13,
+};
+
+static const u32 vusb_idx[] = {
+ 3, 4,
+};
+
+static const u32 vcamd_idx[] = {
+ 3, 4, 5, 6, 7, 9, 12,
+};
+
+static const u32 vefuse_idx[] = {
+ 11, 12, 13,
+};
+
+static const u32 vmch_vemc_idx[] = {
+ 2, 3, 5,
+};
+
+static const u32 vcama_idx[] = {
+ 0, 7, 9, 10, 11, 12,
+};
+
+static const u32 vcn33_bt_wifi_idx[] = {
+ 1, 2, 3,
+};
+
+static const u32 vmc_idx[] = {
+ 4, 10, 11, 13,
+};
+
+static const u32 vldo28_idx[] = {
+ 1, 3,
+};
+
+static unsigned int mt6358_map_mode(unsigned int mode)
+{
+ return mode == MT6358_BUCK_MODE_AUTO ?
+ REGULATOR_MODE_NORMAL : REGULATOR_MODE_FAST;
+}
+
+static int mt6358_set_voltage_sel(struct regulator_dev *rdev,
+ unsigned int selector)
+{
+ int idx, ret;
+ const u32 *pvol;
+ struct mt6358_regulator_info *info = rdev_get_drvdata(rdev);
+
+ pvol = info->index_table;
+
+ idx = pvol[selector];
+ ret = regmap_update_bits(rdev->regmap, info->desc.vsel_reg,
+ info->desc.vsel_mask,
+ idx << info->vsel_shift);
+
+ return ret;
+}
+
+static int mt6358_get_voltage_sel(struct regulator_dev *rdev)
+{
+ int idx, ret;
+ u32 selector;
+ struct mt6358_regulator_info *info = rdev_get_drvdata(rdev);
+ const u32 *pvol;
+
+ ret = regmap_read(rdev->regmap, info->desc.vsel_reg, &selector);
+ if (ret != 0) {
+ dev_info(&rdev->dev,
+ "Failed to get mt6358 %s vsel reg: %d\n",
+ info->desc.name, ret);
+ return ret;
+ }
+
+ selector = (selector & info->desc.vsel_mask) >> info->vsel_shift;
+ pvol = info->index_table;
+ for (idx = 0; idx < info->desc.n_voltages; idx++) {
+ if (pvol[idx] == selector)
+ return idx;
+ }
+
+ return -EINVAL;
+}
+
+static int mt6358_get_buck_voltage_sel(struct regulator_dev *rdev)
+{
+ int ret, regval;
+ struct mt6358_regulator_info *info = rdev_get_drvdata(rdev);
+
+ ret = regmap_read(rdev->regmap, info->da_vsel_reg, ®val);
+ if (ret != 0) {
+ dev_err(&rdev->dev,
+ "Failed to get mt6358 Buck %s vsel reg: %d\n",
+ info->desc.name, ret);
+ return ret;
+ }
+
+ ret = (regval >> info->da_vsel_shift) & info->da_vsel_mask;
+
+ return ret;
+}
+
+static int mt6358_get_status(struct regulator_dev *rdev)
+{
+ int ret;
+ u32 regval;
+ struct mt6358_regulator_info *info = rdev_get_drvdata(rdev);
+
+ ret = regmap_read(rdev->regmap, info->status_reg, ®val);
+ if (ret != 0) {
+ dev_info(&rdev->dev, "Failed to get enable reg: %d\n", ret);
+ return ret;
+ }
+
+ return (regval & info->qi) ? REGULATOR_STATUS_ON : REGULATOR_STATUS_OFF;
+}
+
+static int mt6358_regulator_set_mode(struct regulator_dev *rdev,
+ unsigned int mode)
+{
+ struct mt6358_regulator_info *info = rdev_get_drvdata(rdev);
+ int val;
+
+ switch (mode) {
+ case REGULATOR_MODE_FAST:
+ val = MT6358_BUCK_MODE_FORCE_PWM;
+ break;
+ case REGULATOR_MODE_NORMAL:
+ val = MT6358_BUCK_MODE_AUTO;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ dev_dbg(&rdev->dev, "mt6358 buck set_mode %#x, %#x, %#x, %#x\n",
+ info->modeset_reg, info->modeset_mask,
+ info->modeset_shift, val);
+
+ val <<= info->modeset_shift;
+
+ return regmap_update_bits(rdev->regmap, info->modeset_reg,
+ info->modeset_mask, val);
+}
+
+static unsigned int mt6358_regulator_get_mode(struct regulator_dev *rdev)
+{
+ struct mt6358_regulator_info *info = rdev_get_drvdata(rdev);
+ int ret, regval;
+
+ ret = regmap_read(rdev->regmap, info->modeset_reg, ®val);
+ if (ret != 0) {
+ dev_err(&rdev->dev,
+ "Failed to get mt6358 buck mode: %d\n", ret);
+ return ret;
+ }
+
+ switch ((regval & info->modeset_mask) >> info->modeset_shift) {
+ case MT6358_BUCK_MODE_AUTO:
+ return REGULATOR_MODE_NORMAL;
+ case MT6358_BUCK_MODE_FORCE_PWM:
+ return REGULATOR_MODE_FAST;
+ default:
+ return -EINVAL;
+ }
+}
+
+static const struct regulator_ops mt6358_volt_range_ops = {
+ .list_voltage = regulator_list_voltage_linear_range,
+ .map_voltage = regulator_map_voltage_linear_range,
+ .set_voltage_sel = regulator_set_voltage_sel_regmap,
+ .get_voltage_sel = mt6358_get_buck_voltage_sel,
+ .set_voltage_time_sel = regulator_set_voltage_time_sel,
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .is_enabled = regulator_is_enabled_regmap,
+ .get_status = mt6358_get_status,
+ .set_mode = mt6358_regulator_set_mode,
+ .get_mode = mt6358_regulator_get_mode,
+};
+
+static const struct regulator_ops mt6358_volt_table_ops = {
+ .list_voltage = regulator_list_voltage_table,
+ .map_voltage = regulator_map_voltage_iterate,
+ .set_voltage_sel = mt6358_set_voltage_sel,
+ .get_voltage_sel = mt6358_get_voltage_sel,
+ .set_voltage_time_sel = regulator_set_voltage_time_sel,
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .is_enabled = regulator_is_enabled_regmap,
+ .get_status = mt6358_get_status,
+};
+
+static const struct regulator_ops mt6358_volt_fixed_ops = {
+ .list_voltage = regulator_list_voltage_linear,
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .is_enabled = regulator_is_enabled_regmap,
+ .get_status = mt6358_get_status,
+};
+
+/* The array is indexed by id(MT6358_ID_XXX) */
+static struct mt6358_regulator_info mt6358_regulators[] = {
+ MT6358_BUCK("buck_vdram1", VDRAM1, 500000, 2087500, 12500,
+ buck_volt_range2, 0x7f, MT6358_BUCK_VDRAM1_DBG0, 0x7f,
+ 0, MT6358_VDRAM1_ANA_CON0, 8),
+ MT6358_BUCK("buck_vcore", VCORE, 500000, 1293750, 6250,
+ buck_volt_range1, 0x7f, MT6358_BUCK_VCORE_DBG0, 0x7f,
+ 0, MT6358_VCORE_VGPU_ANA_CON0, 1),
+ MT6358_BUCK("buck_vpa", VPA, 500000, 3650000, 50000,
+ buck_volt_range3, 0x3f, MT6358_BUCK_VPA_DBG0, 0x3f, 0,
+ MT6358_VPA_ANA_CON0, 3),
+ MT6358_BUCK("buck_vproc11", VPROC11, 500000, 1293750, 6250,
+ buck_volt_range1, 0x7f, MT6358_BUCK_VPROC11_DBG0, 0x7f,
+ 0, MT6358_VPROC_ANA_CON0, 1),
+ MT6358_BUCK("buck_vproc12", VPROC12, 500000, 1293750, 6250,
+ buck_volt_range1, 0x7f, MT6358_BUCK_VPROC12_DBG0, 0x7f,
+ 0, MT6358_VPROC_ANA_CON0, 2),
+ MT6358_BUCK("buck_vgpu", VGPU, 500000, 1293750, 6250,
+ buck_volt_range1, 0x7f, MT6358_BUCK_VGPU_ELR0, 0x7f, 0,
+ MT6358_VCORE_VGPU_ANA_CON0, 2),
+ MT6358_BUCK("buck_vs2", VS2, 500000, 2087500, 12500,
+ buck_volt_range2, 0x7f, MT6358_BUCK_VS2_DBG0, 0x7f, 0,
+ MT6358_VS2_ANA_CON0, 8),
+ MT6358_BUCK("buck_vmodem", VMODEM, 500000, 1293750, 6250,
+ buck_volt_range1, 0x7f, MT6358_BUCK_VMODEM_DBG0, 0x7f,
+ 0, MT6358_VMODEM_ANA_CON0, 8),
+ MT6358_BUCK("buck_vs1", VS1, 1000000, 2587500, 12500,
+ buck_volt_range4, 0x7f, MT6358_BUCK_VS1_DBG0, 0x7f, 0,
+ MT6358_VS1_ANA_CON0, 8),
+ MT6358_REG_FIXED("ldo_vrf12", VRF12,
+ MT6358_LDO_VRF12_CON0, 0, 1200000),
+ MT6358_REG_FIXED("ldo_vio18", VIO18,
+ MT6358_LDO_VIO18_CON0, 0, 1800000),
+ MT6358_REG_FIXED("ldo_vcamio", VCAMIO,
+ MT6358_LDO_VCAMIO_CON0, 0, 1800000),
+ MT6358_REG_FIXED("ldo_vcn18", VCN18, MT6358_LDO_VCN18_CON0, 0, 1800000),
+ MT6358_REG_FIXED("ldo_vfe28", VFE28, MT6358_LDO_VFE28_CON0, 0, 2800000),
+ MT6358_REG_FIXED("ldo_vcn28", VCN28, MT6358_LDO_VCN28_CON0, 0, 2800000),
+ MT6358_REG_FIXED("ldo_vxo22", VXO22, MT6358_LDO_VXO22_CON0, 0, 2200000),
+ MT6358_REG_FIXED("ldo_vaux18", VAUX18,
+ MT6358_LDO_VAUX18_CON0, 0, 1800000),
+ MT6358_REG_FIXED("ldo_vbif28", VBIF28,
+ MT6358_LDO_VBIF28_CON0, 0, 2800000),
+ MT6358_REG_FIXED("ldo_vio28", VIO28, MT6358_LDO_VIO28_CON0, 0, 2800000),
+ MT6358_REG_FIXED("ldo_va12", VA12, MT6358_LDO_VA12_CON0, 0, 1200000),
+ MT6358_REG_FIXED("ldo_vrf18", VRF18, MT6358_LDO_VRF18_CON0, 0, 1800000),
+ MT6358_REG_FIXED("ldo_vaud28", VAUD28,
+ MT6358_LDO_VAUD28_CON0, 0, 2800000),
+ MT6358_LDO("ldo_vdram2", VDRAM2, vdram2_voltages, vdram2_idx,
+ MT6358_LDO_VDRAM2_CON0, 0, MT6358_LDO_VDRAM2_ELR0, 0x10, 0),
+ MT6358_LDO("ldo_vsim1", VSIM1, vsim_voltages, vsim_idx,
+ MT6358_LDO_VSIM1_CON0, 0, MT6358_VSIM1_ANA_CON0, 0xf00, 8),
+ MT6358_LDO("ldo_vibr", VIBR, vibr_voltages, vibr_idx,
+ MT6358_LDO_VIBR_CON0, 0, MT6358_VIBR_ANA_CON0, 0xf00, 8),
+ MT6358_LDO("ldo_vusb", VUSB, vusb_voltages, vusb_idx,
+ MT6358_LDO_VUSB_CON0_0, 0, MT6358_VUSB_ANA_CON0, 0x700, 8),
+ MT6358_LDO("ldo_vcamd", VCAMD, vcamd_voltages, vcamd_idx,
+ MT6358_LDO_VCAMD_CON0, 0, MT6358_VCAMD_ANA_CON0, 0xf00, 8),
+ MT6358_LDO("ldo_vefuse", VEFUSE, vefuse_voltages, vefuse_idx,
+ MT6358_LDO_VEFUSE_CON0, 0, MT6358_VEFUSE_ANA_CON0, 0xf00, 8),
+ MT6358_LDO("ldo_vmch", VMCH, vmch_vemc_voltages, vmch_vemc_idx,
+ MT6358_LDO_VMCH_CON0, 0, MT6358_VMCH_ANA_CON0, 0x700, 8),
+ MT6358_LDO("ldo_vcama1", VCAMA1, vcama_voltages, vcama_idx,
+ MT6358_LDO_VCAMA1_CON0, 0, MT6358_VCAMA1_ANA_CON0, 0xf00, 8),
+ MT6358_LDO("ldo_vemc", VEMC, vmch_vemc_voltages, vmch_vemc_idx,
+ MT6358_LDO_VEMC_CON0, 0, MT6358_VEMC_ANA_CON0, 0x700, 8),
+ MT6358_LDO("ldo_vcn33_bt", VCN33_BT, vcn33_bt_wifi_voltages,
+ vcn33_bt_wifi_idx, MT6358_LDO_VCN33_CON0_0,
+ 0, MT6358_VCN33_ANA_CON0, 0x300, 8),
+ MT6358_LDO("ldo_vcn33_wifi", VCN33_WIFI, vcn33_bt_wifi_voltages,
+ vcn33_bt_wifi_idx, MT6358_LDO_VCN33_CON0_1,
+ 0, MT6358_VCN33_ANA_CON0, 0x300, 8),
+ MT6358_LDO("ldo_vcama2", VCAMA2, vcama_voltages, vcama_idx,
+ MT6358_LDO_VCAMA2_CON0, 0, MT6358_VCAMA2_ANA_CON0, 0xf00, 8),
+ MT6358_LDO("ldo_vmc", VMC, vmc_voltages, vmc_idx,
+ MT6358_LDO_VMC_CON0, 0, MT6358_VMC_ANA_CON0, 0xf00, 8),
+ MT6358_LDO("ldo_vldo28", VLDO28, vldo28_voltages, vldo28_idx,
+ MT6358_LDO_VLDO28_CON0_0, 0,
+ MT6358_VLDO28_ANA_CON0, 0x300, 8),
+ MT6358_LDO("ldo_vsim2", VSIM2, vsim_voltages, vsim_idx,
+ MT6358_LDO_VSIM2_CON0, 0, MT6358_VSIM2_ANA_CON0, 0xf00, 8),
+ MT6358_LDO1("ldo_vsram_proc11", VSRAM_PROC11, 500000, 1293750, 6250,
+ buck_volt_range1, MT6358_LDO_VSRAM_PROC11_DBG0, 0x7f, 8,
+ MT6358_LDO_VSRAM_CON0, 0x7f),
+ MT6358_LDO1("ldo_vsram_others", VSRAM_OTHERS, 500000, 1293750, 6250,
+ buck_volt_range1, MT6358_LDO_VSRAM_OTHERS_DBG0, 0x7f, 8,
+ MT6358_LDO_VSRAM_CON2, 0x7f),
+ MT6358_LDO1("ldo_vsram_gpu", VSRAM_GPU, 500000, 1293750, 6250,
+ buck_volt_range1, MT6358_LDO_VSRAM_GPU_DBG0, 0x7f, 8,
+ MT6358_LDO_VSRAM_CON3, 0x7f),
+ MT6358_LDO1("ldo_vsram_proc12", VSRAM_PROC12, 500000, 1293750, 6250,
+ buck_volt_range1, MT6358_LDO_VSRAM_PROC12_DBG0, 0x7f, 8,
+ MT6358_LDO_VSRAM_CON1, 0x7f),
+};
+
+static int mt6358_regulator_probe(struct platform_device *pdev)
+{
+ struct mt6397_chip *mt6397 = dev_get_drvdata(pdev->dev.parent);
+ struct regulator_config config = {};
+ struct regulator_dev *rdev;
+ int i;
+
+ for (i = 0; i < MT6358_MAX_REGULATOR; i++) {
+ config.dev = &pdev->dev;
+ config.driver_data = &mt6358_regulators[i];
+ config.regmap = mt6397->regmap;
+
+ rdev = devm_regulator_register(&pdev->dev,
+ &mt6358_regulators[i].desc,
+ &config);
+ if (IS_ERR(rdev)) {
+ dev_err(&pdev->dev, "failed to register %s\n",
+ mt6358_regulators[i].desc.name);
+ return PTR_ERR(rdev);
+ }
+ }
+
+ return 0;
+}
+
+static const struct platform_device_id mt6358_platform_ids[] = {
+ {"mt6358-regulator", 0},
+ { /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(platform, mt6358_platform_ids);
+
+static struct platform_driver mt6358_regulator_driver = {
+ .driver = {
+ .name = "mt6358-regulator",
+ },
+ .probe = mt6358_regulator_probe,
+ .id_table = mt6358_platform_ids,
+};
+
+module_platform_driver(mt6358_regulator_driver);
+
+MODULE_AUTHOR("Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>");
+MODULE_DESCRIPTION("Regulator Driver for MediaTek MT6358 PMIC");
+MODULE_LICENSE("GPL");
diff --git a/include/linux/regulator/mt6358-regulator.h b/include/linux/regulator/mt6358-regulator.h
new file mode 100644
index 0000000..1cc3049
--- /dev/null
+++ b/include/linux/regulator/mt6358-regulator.h
@@ -0,0 +1,56 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2019 MediaTek Inc.
+ */
+
+#ifndef __LINUX_REGULATOR_MT6358_H
+#define __LINUX_REGULATOR_MT6358_H
+
+enum {
+ MT6358_ID_VDRAM1 = 0,
+ MT6358_ID_VCORE,
+ MT6358_ID_VPA,
+ MT6358_ID_VPROC11,
+ MT6358_ID_VPROC12,
+ MT6358_ID_VGPU,
+ MT6358_ID_VS2,
+ MT6358_ID_VMODEM,
+ MT6358_ID_VS1,
+ MT6358_ID_VDRAM2 = 9,
+ MT6358_ID_VSIM1,
+ MT6358_ID_VIBR,
+ MT6358_ID_VRF12,
+ MT6358_ID_VIO18,
+ MT6358_ID_VUSB,
+ MT6358_ID_VCAMIO,
+ MT6358_ID_VCAMD,
+ MT6358_ID_VCN18,
+ MT6358_ID_VFE28,
+ MT6358_ID_VSRAM_PROC11,
+ MT6358_ID_VCN28,
+ MT6358_ID_VSRAM_OTHERS,
+ MT6358_ID_VSRAM_GPU,
+ MT6358_ID_VXO22,
+ MT6358_ID_VEFUSE,
+ MT6358_ID_VAUX18,
+ MT6358_ID_VMCH,
+ MT6358_ID_VBIF28,
+ MT6358_ID_VSRAM_PROC12,
+ MT6358_ID_VCAMA1,
+ MT6358_ID_VEMC,
+ MT6358_ID_VIO28,
+ MT6358_ID_VA12,
+ MT6358_ID_VRF18,
+ MT6358_ID_VCN33_BT,
+ MT6358_ID_VCN33_WIFI,
+ MT6358_ID_VCAMA2,
+ MT6358_ID_VMC,
+ MT6358_ID_VLDO28,
+ MT6358_ID_VAUD28,
+ MT6358_ID_VSIM2,
+ MT6358_ID_RG_MAX,
+};
+
+#define MT6358_MAX_REGULATOR MT6358_ID_RG_MAX
+
+#endif /* __LINUX_REGULATOR_MT6358_H */
--
1.9.1
next prev parent reply other threads:[~2019-08-23 3:46 UTC|newest]
Thread overview: 32+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-08-23 3:45 [PATCH v5 00/10] Add Support for MediaTek PMIC MT6358 Hsin-Hsiung Wang
2019-08-23 3:45 ` [PATCH v5 01/10] mfd: mt6397: clean up code Hsin-Hsiung Wang
2019-08-23 3:45 ` [PATCH v5 02/10] mfd: mt6397: extract irq related code from core driver Hsin-Hsiung Wang
2019-08-23 12:13 ` [BUG] " Frank Wunderlich
2019-08-23 14:56 ` Matthias Brugger
2019-08-23 15:26 ` Frank Wunderlich
2019-08-23 15:42 ` Matthias Brugger
2019-08-23 17:16 ` Aw: " Frank Wunderlich
2019-08-29 6:24 ` Hsin-hsiung Wang
2019-09-19 18:59 ` Frank Wunderlich
2019-09-30 19:44 ` Aw: " Frank Wunderlich
2019-08-23 15:35 ` Frank Wunderlich
2019-08-23 15:53 ` Frank Wunderlich
2019-08-23 14:53 ` Matthias Brugger
2019-08-23 3:45 ` [PATCH v5 03/10] mfd: mt6397: modify suspend/resume behavior Hsin-Hsiung Wang
2019-08-23 15:12 ` Matthias Brugger
2019-08-23 3:45 ` [PATCH v5 04/10] dt-bindings: mfd: Add compatible for the MediaTek MT6358 PMIC Hsin-Hsiung Wang
2019-08-23 3:45 ` [PATCH v5 05/10] regulator: Add document for MT6358 regulator Hsin-Hsiung Wang
2019-08-28 10:44 ` Mark Brown
2019-08-28 13:13 ` Applied "regulator: Add document for MT6358 regulator" to the regulator tree Mark Brown
2019-08-23 3:45 ` [PATCH v5 06/10] mfd: Add support for the MediaTek MT6358 PMIC Hsin-Hsiung Wang
2019-12-02 8:06 ` Pi-Hsun Shih
2019-12-06 8:55 ` Hsin-hsiung Wang
2019-08-23 3:45 ` Hsin-Hsiung Wang [this message]
2019-08-28 10:45 ` [PATCH v5 07/10] regulator: mt6358: Add support for MT6358 regulator Mark Brown
2019-08-29 6:09 ` Hsin-hsiung Wang
2019-08-28 13:13 ` Applied "regulator: mt6358: Add support for MT6358 regulator" to the regulator tree Mark Brown
2019-08-23 3:45 ` [PATCH v5 08/10] arm64: dts: mt6358: add PMIC MT6358 related nodes Hsin-Hsiung Wang
2019-08-23 3:45 ` [PATCH v5 09/10] rtc: mt6397: fix alarm register overwrite Hsin-Hsiung Wang
2019-08-23 15:35 ` Matthias Brugger
2019-08-29 5:34 ` Hsin-hsiung Wang
2019-08-23 3:45 ` [PATCH v5 10/10] rtc: mt6397: Add support for the MediaTek MT6358 RTC Hsin-Hsiung Wang
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1566531931-9772-8-git-send-email-hsin-hsiung.wang@mediatek.com \
--to=hsin-hsiung.wang@mediatek.com \
--cc=a.zummo@towertech.it \
--cc=alexandre.belloni@bootlin.com \
--cc=broonie@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=eddie.huang@mediatek.com \
--cc=gregkh@linuxfoundation.org \
--cc=kstewart@linuxfoundation.org \
--cc=lee.jones@linaro.org \
--cc=lgirdwood@gmail.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mediatek@lists.infradead.org \
--cc=linux-rtc@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=matthias.bgg@gmail.com \
--cc=rfontana@redhat.com \
--cc=robh+dt@kernel.org \
--cc=sean.wang@mediatek.com \
--cc=srv_heupstream@mediatek.com \
--cc=tglx@linutronix.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).