From: Stefan-gabriel Mirea <stefan-gabriel.mirea@nxp.com>
To: "corbet@lwn.net" <corbet@lwn.net>,
"robh+dt@kernel.org" <robh+dt@kernel.org>,
"mark.rutland@arm.com" <mark.rutland@arm.com>,
"gregkh@linuxfoundation.org" <gregkh@linuxfoundation.org>,
"catalin.marinas@arm.com" <catalin.marinas@arm.com>,
"will@kernel.org" <will@kernel.org>,
"shawnguo@kernel.org" <shawnguo@kernel.org>,
Leo Li <leoyang.li@nxp.com>
Cc: "jslaby@suse.com" <jslaby@suse.com>,
"linux-doc@vger.kernel.org" <linux-doc@vger.kernel.org>,
"linux-kernel@vger.kernel.org" <linux-kernel@vger.kernel.org>,
"devicetree@vger.kernel.org" <devicetree@vger.kernel.org>,
"linux-serial@vger.kernel.org" <linux-serial@vger.kernel.org>,
"linux-arm-kernel@lists.infradead.org"
<linux-arm-kernel@lists.infradead.org>,
Cosmin Stefan Stoica <cosmin.stoica@nxp.com>,
Dan Nica <dan.nica@nxp.com>,
Larisa Ileana Grigore <larisa.grigore@nxp.com>
Subject: [PATCH v3 5/7] arm64: dts: fsl: Add device tree for S32V234-EVB
Date: Fri, 23 Aug 2019 19:11:38 +0000 [thread overview]
Message-ID: <20190823191115.18490-6-stefan-gabriel.mirea@nxp.com> (raw)
In-Reply-To: <20190823191115.18490-1-stefan-gabriel.mirea@nxp.com>
From: Stoica Cosmin-Stefan <cosmin.stoica@nxp.com>
Add initial version of device tree for S32V234-EVB, including nodes for the
4 Cortex-A53 cores, AIPS bus with UART modules, ARM architected timer and
Generic Interrupt Controller (GIC).
Keep SoC level separate from board level to let future boards with this SoC
share common properties, while the dts files will keep board-dependent
properties.
Signed-off-by: Stoica Cosmin-Stefan <cosmin.stoica@nxp.com>
Signed-off-by: Mihaela Martinas <Mihaela.Martinas@freescale.com>
Signed-off-by: Dan Nica <dan.nica@nxp.com>
Signed-off-by: Larisa Grigore <Larisa.Grigore@nxp.com>
Signed-off-by: Phu Luu An <phu.luuan@nxp.com>
Signed-off-by: Stefan-Gabriel Mirea <stefan-gabriel.mirea@nxp.com>
---
arch/arm64/boot/dts/freescale/Makefile | 2 +
arch/arm64/boot/dts/freescale/s32v234-evb.dts | 25 ++++
arch/arm64/boot/dts/freescale/s32v234.dtsi | 139 ++++++++++++++++++
3 files changed, 166 insertions(+)
create mode 100644 arch/arm64/boot/dts/freescale/s32v234-evb.dts
create mode 100644 arch/arm64/boot/dts/freescale/s32v234.dtsi
diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index c043aca66572..9aff21324146 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -26,3 +26,5 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-devkit.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mq-zii-ultra-rmb3.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mq-zii-ultra-zest.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8qxp-mek.dtb
+
+dtb-$(CONFIG_ARCH_S32) += s32v234-evb.dtb
diff --git a/arch/arm64/boot/dts/freescale/s32v234-evb.dts b/arch/arm64/boot/dts/freescale/s32v234-evb.dts
new file mode 100644
index 000000000000..4b802518cefc
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/s32v234-evb.dts
@@ -0,0 +1,25 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2015-2016 Freescale Semiconductor, Inc.
+ * Copyright 2016-2017 NXP
+ */
+
+/dts-v1/;
+#include "s32v234.dtsi"
+
+/ {
+ model = "NXP S32V234-EVB2 Board";
+ compatible = "fsl,s32v234-evb", "fsl,s32v234";
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&uart1 {
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/freescale/s32v234.dtsi b/arch/arm64/boot/dts/freescale/s32v234.dtsi
new file mode 100644
index 000000000000..37225191ccbf
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/s32v234.dtsi
@@ -0,0 +1,139 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2015-2016 Freescale Semiconductor, Inc.
+ * Copyright 2016-2018 NXP
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/memreserve/ 0x80000000 0x00010000;
+
+/ {
+ compatible = "fsl,s32v234";
+ interrupt-parent = <&gic>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ aliases {
+ serial0 = &uart0;
+ serial1 = &uart1;
+ };
+
+ cpus {
+ #address-cells = <2>;
+ #size-cells = <0>;
+
+ cpu0: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0x0 0x0>;
+ enable-method = "spin-table";
+ cpu-release-addr = <0x0 0x80000000>;
+ next-level-cache = <&cluster0_l2_cache>;
+ };
+
+ cpu1: cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0x0 0x1>;
+ enable-method = "spin-table";
+ cpu-release-addr = <0x0 0x80000000>;
+ next-level-cache = <&cluster0_l2_cache>;
+ };
+
+ cpu2: cpu@100 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0x0 0x100>;
+ enable-method = "spin-table";
+ cpu-release-addr = <0x0 0x80000000>;
+ next-level-cache = <&cluster1_l2_cache>;
+ };
+
+ cpu3: cpu@101 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0x0 0x101>;
+ enable-method = "spin-table";
+ cpu-release-addr = <0x0 0x80000000>;
+ next-level-cache = <&cluster1_l2_cache>;
+ };
+
+ cluster0_l2_cache: l2-cache0 {
+ compatible = "cache";
+ };
+
+ cluster1_l2_cache: l2-cache1 {
+ compatible = "cache";
+ };
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) |
+ IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) |
+ IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) |
+ IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) |
+ IRQ_TYPE_LEVEL_LOW)>;
+ /* clock-frequency might be modified by u-boot, depending on the
+ * chip version.
+ */
+ clock-frequency = <10000000>;
+ };
+
+ gic: interrupt-controller@7d001000 {
+ compatible = "arm,cortex-a15-gic", "arm,cortex-a9-gic";
+ #interrupt-cells = <3>;
+ #address-cells = <0>;
+ interrupt-controller;
+ reg = <0 0x7d001000 0 0x1000>,
+ <0 0x7d002000 0 0x2000>,
+ <0 0x7d004000 0 0x2000>,
+ <0 0x7d006000 0 0x2000>;
+ interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) |
+ IRQ_TYPE_LEVEL_HIGH)>;
+ };
+
+ soc {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ compatible = "simple-bus";
+ interrupt-parent = <&gic>;
+ ranges;
+
+ aips0: aips-bus@40000000 {
+ compatible = "simple-bus";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ interrupt-parent = <&gic>;
+ reg = <0x0 0x40000000 0x0 0x7D000>;
+ ranges;
+
+ uart0: serial@40053000 {
+ compatible = "fsl,s32v234-linflexuart";
+ reg = <0x0 0x40053000 0x0 0x1000>;
+ interrupts = <GIC_SPI 59 IRQ_TYPE_EDGE_RISING>;
+ status = "disabled";
+ };
+ };
+
+ aips1: aips-bus@40080000 {
+ compatible = "simple-bus";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ interrupt-parent = <&gic>;
+ reg = <0x0 0x40080000 0x0 0x70000>;
+ ranges;
+
+ uart1: serial@400bc000 {
+ compatible = "fsl,s32v234-linflexuart";
+ reg = <0x0 0x400bc000 0x0 0x1000>;
+ interrupts = <GIC_SPI 60 IRQ_TYPE_EDGE_RISING>;
+ status = "disabled";
+ };
+ };
+ };
+};
--
2.22.0
next prev parent reply other threads:[~2019-08-23 19:12 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-08-23 19:11 [PATCH v3 0/7] Add initial support for S32V234-EVB Stefan-gabriel Mirea
2019-08-23 19:11 ` [PATCH v3 1/7] dt-bindings: arm: fsl: Add the S32V234-EVB board Stefan-gabriel Mirea
2019-08-23 19:11 ` [PATCH v3 2/7] arm64: Introduce config for S32 Stefan-gabriel Mirea
2019-08-23 19:11 ` [PATCH v3 3/7] serial: fsl_linflexuart: Update compatible string Stefan-gabriel Mirea
2019-08-23 19:11 ` [PATCH v3 4/7] serial: fsl_linflexuart: Be consistent with the name Stefan-gabriel Mirea
2019-09-04 7:52 ` gregkh
2019-09-05 11:32 ` Stefan-gabriel Mirea
2019-08-23 19:11 ` Stefan-gabriel Mirea [this message]
2019-08-23 19:11 ` [PATCH v3 6/7] dt-bindings: serial: Document Freescale LINFlexD UART Stefan-gabriel Mirea
2019-08-27 20:26 ` Rob Herring
2019-08-23 19:11 ` [PATCH v3 7/7] arm64: defconfig: Enable configs for S32V234 Stefan-gabriel Mirea
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190823191115.18490-6-stefan-gabriel.mirea@nxp.com \
--to=stefan-gabriel.mirea@nxp.com \
--cc=catalin.marinas@arm.com \
--cc=corbet@lwn.net \
--cc=cosmin.stoica@nxp.com \
--cc=dan.nica@nxp.com \
--cc=devicetree@vger.kernel.org \
--cc=gregkh@linuxfoundation.org \
--cc=jslaby@suse.com \
--cc=larisa.grigore@nxp.com \
--cc=leoyang.li@nxp.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-doc@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-serial@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=robh+dt@kernel.org \
--cc=shawnguo@kernel.org \
--cc=will@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).