From: Lubomir Rintel <lkundrak@v3.sk>
To: Olof Johansson <olof@lixom.net>
Cc: Rob Herring <robh+dt@kernel.org>,
Mark Rutland <mark.rutland@arm.com>,
linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org, Pavel Machek <pavel@ucw.cz>,
Lubomir Rintel <lkundrak@v3.sk>
Subject: [PATCH v3 6/6] ARM: dts: mmp2: add OLPC XO 1.75 machine
Date: Wed, 28 Aug 2019 09:26:29 +0200 [thread overview]
Message-ID: <20190828072629.285760-7-lkundrak@v3.sk> (raw)
In-Reply-To: <20190828072629.285760-1-lkundrak@v3.sk>
This is a fairly complete description of an OLPC XO 1.75 laptop.
What's missing for now is the GPU, LCD controller, DCON, the panel and
audio.
The machine is booted with OpenFirmware and thus has a devicetree.
However, older versions are unable to create a valid FDT and don't
follow the Linux bindings. Having an device tree in the kernel tree
makes it easier to use mainline kernels on such machines, test changes
with CONFIG_ARM_APPENDED_DTB and give a good reference on what bindings
are used on the machine without an access to one.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Pavel Machek <pavel@ucw.cz>
---
Changes since v1:
- Added this patch
arch/arm/boot/dts/Makefile | 3 +-
arch/arm/boot/dts/mmp2-olpc-xo-1-75.dts | 244 ++++++++++++++++++++++++
2 files changed, 246 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/boot/dts/mmp2-olpc-xo-1-75.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 9159fa2cea90c..65213b5265187 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -336,7 +336,8 @@ dtb-$(CONFIG_MACH_MESON8) += \
dtb-$(CONFIG_ARCH_MMP) += \
pxa168-aspenite.dtb \
pxa910-dkb.dtb \
- mmp2-brownstone.dtb
+ mmp2-brownstone.dtb \
+ mmp2-olpc-xo-1-75.dtb
dtb-$(CONFIG_ARCH_MPS2) += \
mps2-an385.dtb \
mps2-an399.dtb
diff --git a/arch/arm/boot/dts/mmp2-olpc-xo-1-75.dts b/arch/arm/boot/dts/mmp2-olpc-xo-1-75.dts
new file mode 100644
index 0000000000000..6cfa0d4a18845
--- /dev/null
+++ b/arch/arm/boot/dts/mmp2-olpc-xo-1-75.dts
@@ -0,0 +1,244 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * OLPC XO 1.75 Laptop.
+ *
+ * Copyright (C) 2018,2019 Lubomir Rintel <lkundrak@v3.sk>
+ */
+
+/dts-v1/;
+#include "mmp2.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+ model = "OLPC XO-1.75";
+ compatible = "olpc,xo-1.75", "mrvl,mmp2";
+
+ chosen {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ framebuffer@1fc00000 {
+ compatible = "simple-framebuffer";
+ reg = <0x1fc00000 (1200 * 900 * 2)>;
+ width = <1200>;
+ height = <900>;
+ stride = <(1200 * 2)>;
+ format = "r5g6b5";
+ clocks = <&soc_clocks MMP2_CLK_DISP0_LCDC>,
+ <&soc_clocks MMP2_CLK_DISP0>;
+ };
+ };
+
+ memory {
+ linux,usable-memory = <0x0 0x1f800000>;
+ available = <0xcf000 0x1ef31000 0x1000 0xbf000>;
+ reg = <0x0 0x20000000>;
+ device_type = "memory";
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ lid {
+ label = "Lid";
+ gpios = <&gpio 129 GPIO_ACTIVE_LOW>;
+ linux,input-type = <EV_SW>;
+ linux,code = <SW_LID>;
+ wakeup-source;
+ };
+
+ tablet_mode {
+ label = "E-Book Mode";
+ gpios = <&gpio 128 GPIO_ACTIVE_LOW>;
+ linux,input-type = <EV_SW>;
+ linux,code = <SW_TABLET_MODE>;
+ wakeup-source;
+ };
+
+ microphone_insert {
+ label = "Microphone Plug";
+ gpios = <&gpio 96 GPIO_ACTIVE_HIGH>;
+ linux,input-type = <EV_SW>;
+ linux,code = <SW_MICROPHONE_INSERT>;
+ debounce-interval = <100>;
+ wakeup-source;
+ };
+
+ headphone_insert {
+ label = "Headphone Plug";
+ gpios = <&gpio 97 GPIO_ACTIVE_HIGH>;
+ linux,input-type = <EV_SW>;
+ linux,code = <SW_HEADPHONE_INSERT>;
+ debounce-interval = <100>;
+ wakeup-source;
+ };
+ };
+
+ camera_i2c {
+ compatible = "i2c-gpio";
+ gpios = <&gpio 109 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>,
+ <&gpio 108 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ i2c-gpio,timeout-ms = <1000>;
+ status = "okay";
+
+ camera@21 {
+ compatible = "ovti,ov7670";
+ reg = <0x21>;
+ reset-gpios = <&gpio 102 GPIO_ACTIVE_LOW>;
+ powerdown-gpios = <&gpio 150 GPIO_ACTIVE_LOW>;
+ clocks = <&camera0>;
+ clock-names = "xclk";
+
+ port {
+ ov7670_0: endpoint {
+ hsync-active = <1>;
+ vsync-active = <1>;
+ remote-endpoint = <&camera0_0>;
+ };
+ };
+ };
+ };
+
+ battery {
+ compatible = "olpc,xo1.5-battery", "olpc,xo1-battery";
+ };
+
+ wlan_reg: fixedregulator0 {
+ compatible = "regulator-fixed";
+ regulator-name = "wlan";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio 34 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ wlan_pwrseq: pwrseq0 {
+ compatible = "mmc-pwrseq-sd8787";
+ powerdown-gpios = <&gpio 57 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&gpio 58 GPIO_ACTIVE_HIGH>;
+ };
+
+ soc {
+ axi@d4200000 {
+ ap-sp@d4290000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "olpc,ap-sp";
+ interrupts = <40>;
+ reg = <0xd4290000 0x1000>;
+ data-gpios = <&gpio 72 GPIO_ACTIVE_HIGH>;
+ clk-gpios = <&gpio 71 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+ };
+ };
+ };
+};
+
+&uart3 {
+ status = "okay";
+};
+
+&uart4 {
+ status = "okay";
+};
+
+&rtc {
+ status = "okay";
+};
+
+&usb_phy0 {
+ status = "okay";
+};
+
+&usb_otg0 {
+ status = "okay";
+};
+
+&mmc1 {
+ clock-frequency = <50000000>;
+ no-1-8-v;
+ mrvl,clk-delay-cycles = <31>;
+ broken-cd;
+ status = "okay";
+};
+
+&mmc2 {
+ clock-frequency = <50000000>;
+ no-1-8-v;
+ bus-width = <4>;
+ non-removable;
+ broken-cd;
+ wakeup-source;
+ keep-power-in-suspend;
+ mmc-pwrseq = <&wlan_pwrseq>;
+ vmmc-supply = <&wlan_reg>;
+ status = "okay";
+};
+
+&mmc3 {
+ clock-frequency = <50000000>;
+ no-1-8-v;
+ bus-width = <8>;
+ non-removable;
+ broken-cd;
+ mrvl,clk-delay-cycles = <31>;
+ status = "okay";
+};
+
+&twsi1 {
+ status = "okay";
+
+ audio-codec@1a {
+ compatible = "realtek,alc5631";
+ reg = <0x1a>;
+ status = "okay";
+ };
+};
+
+&twsi2 {
+ status = "okay";
+
+ rtc@68 {
+ compatible = "dallas,ds1338";
+ reg = <0x68>;
+ status = "okay";
+ };
+};
+
+&twsi6 {
+ status = "okay";
+
+ accelerometer@1d {
+ compatible = "st,lis331dlh", "st,lis3lv02d";
+ reg = <0x1d>;
+ status = "okay";
+ };
+};
+
+&ssp3 {
+ #address-cells = <0>;
+ spi-slave;
+ status = "okay";
+ ready-gpio = <&gpio 125 GPIO_ACTIVE_HIGH>;
+
+ slave {
+ compatible = "olpc,xo1.75-ec";
+ spi-cpha;
+ cmd-gpio = <&gpio 155 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&camera0 {
+ status = "okay";
+
+ port {
+ camera0_0: endpoint {
+ remote-endpoint = <&ov7670_0>;
+ };
+ };
+};
--
2.21.0
next prev parent reply other threads:[~2019-08-28 7:27 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-08-28 7:26 [PATCH v3 0/6] ARM: dts: mmp2: devicetree updates Lubomir Rintel
2019-08-28 7:26 ` [PATCH v3 1/6] ARM: dts: mmp2: trivial whitespace fix Lubomir Rintel
2019-08-28 7:26 ` [PATCH v3 2/6] ARM: dts: mmp2: fix the SPI nodes Lubomir Rintel
2019-08-28 7:26 ` [PATCH v3 3/6] ARM: dts: mmp2: rename the USB PHY node Lubomir Rintel
2019-08-28 7:26 ` [PATCH v3 4/6] ARM: dts: mmp2: add camera interfaces Lubomir Rintel
2019-08-28 7:26 ` [PATCH v3 5/6] ARM: dts: mmp2: specify reg-shift for the UARTs Lubomir Rintel
2019-08-28 7:26 ` Lubomir Rintel [this message]
2019-09-07 19:40 ` [PATCH v3 0/6] ARM: dts: mmp2: devicetree updates Pavel Machek
2019-09-07 19:57 ` Arnd Bergmann
2019-09-07 20:47 ` Pavel Machek
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190828072629.285760-7-lkundrak@v3.sk \
--to=lkundrak@v3.sk \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=olof@lixom.net \
--cc=pavel@ucw.cz \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).