From: Schrempf Frieder <frieder.schrempf@kontron.de>
To: "krzk@kernel.org" <krzk@kernel.org>,
"robh+dt@kernel.org" <robh+dt@kernel.org>,
Schrempf Frieder <frieder.schrempf@kontron.de>,
"Mark Rutland" <mark.rutland@arm.com>,
Shawn Guo <shawnguo@kernel.org>,
Sascha Hauer <s.hauer@pengutronix.de>,
Pengutronix Kernel Team <kernel@pengutronix.de>,
Fabio Estevam <festevam@gmail.com>,
NXP Linux Team <linux-imx@nxp.com>
Cc: "devicetree@vger.kernel.org" <devicetree@vger.kernel.org>,
"linux-arm-kernel@lists.infradead.org"
<linux-arm-kernel@lists.infradead.org>,
"linux-kernel@vger.kernel.org" <linux-kernel@vger.kernel.org>
Subject: [PATCH 01/10] ARM: dts: imx6ul-kontron-n6310: Move common SoM nodes to a separate file
Date: Wed, 16 Oct 2019 15:07:19 +0000 [thread overview]
Message-ID: <20191016150622.21753-2-frieder.schrempf@kontron.de> (raw)
In-Reply-To: <20191016150622.21753-1-frieder.schrempf@kontron.de>
From: Frieder Schrempf <frieder.schrempf@kontron.de>
The Kontron N6311 and N6411 SoMs are very similar to N6310. In
preparation to add support for them, we move the common nodes to a
separate file imx6ul-kontron-n6x1x-som-common.dtsi.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
.../boot/dts/imx6ul-kontron-n6310-som.dtsi | 95 +-------------
.../dts/imx6ul-kontron-n6x1x-som-common.dtsi | 123 ++++++++++++++++++
2 files changed, 124 insertions(+), 94 deletions(-)
create mode 100644 arch/arm/boot/dts/imx6ul-kontron-n6x1x-som-common.dtsi
diff --git a/arch/arm/boot/dts/imx6ul-kontron-n6310-som.dtsi b/arch/arm/boot/dts/imx6ul-kontron-n6310-som.dtsi
index a896b2348dd2..47d3ce5d255f 100644
--- a/arch/arm/boot/dts/imx6ul-kontron-n6310-som.dtsi
+++ b/arch/arm/boot/dts/imx6ul-kontron-n6310-som.dtsi
@@ -6,7 +6,7 @@
*/
#include "imx6ul.dtsi"
-#include <dt-bindings/gpio/gpio.h>
+#include "imx6ul-kontron-n6x1x-som-common.dtsi"
/ {
model = "Kontron N6310 SOM";
@@ -18,49 +18,7 @@
};
};
-&ecspi2 {
- cs-gpios = <&gpio4 22 GPIO_ACTIVE_HIGH>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_ecspi2>;
- status = "okay";
-
- spi-flash@0 {
- compatible = "mxicy,mx25v8035f", "jedec,spi-nor";
- spi-max-frequency = <50000000>;
- reg = <0>;
- };
-};
-
-&fec1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_enet1 &pinctrl_enet1_mdio>;
- phy-mode = "rmii";
- phy-handle = <ðphy1>;
- status = "okay";
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
-
- ethphy1: ethernet-phy@1 {
- reg = <1>;
- micrel,led-mode = <0>;
- clocks = <&clks IMX6UL_CLK_ENET_REF>;
- clock-names = "rmii-ref";
- };
- };
-};
-
-&fec2 {
- phy-mode = "rmii";
- status = "disabled";
-};
-
&qspi {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_qspi>;
- status = "okay";
-
spi-flash@0 {
#address-cells = <1>;
#size-cells = <1>;
@@ -81,54 +39,3 @@
};
};
};
-
-&iomuxc {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_reset_out>;
-
- pinctrl_ecspi2: ecspi2grp {
- fsl,pins = <
- MX6UL_PAD_CSI_DATA03__ECSPI2_MISO 0x100b1
- MX6UL_PAD_CSI_DATA02__ECSPI2_MOSI 0x100b1
- MX6UL_PAD_CSI_DATA00__ECSPI2_SCLK 0x100b1
- MX6UL_PAD_CSI_DATA01__GPIO4_IO22 0x100b1
- >;
- };
-
- pinctrl_enet1: enet1grp {
- fsl,pins = <
- MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN 0x1b0b0
- MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER 0x1b0b0
- MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00 0x1b0b0
- MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01 0x1b0b0
- MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN 0x1b0b0
- MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00 0x1b0b0
- MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01 0x1b0b0
- MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 0x4001b009
- >;
- };
-
- pinctrl_enet1_mdio: enet1mdiogrp {
- fsl,pins = <
- MX6UL_PAD_GPIO1_IO07__ENET1_MDC 0x1b0b0
- MX6UL_PAD_GPIO1_IO06__ENET1_MDIO 0x1b0b0
- >;
- };
-
- pinctrl_qspi: qspigrp {
- fsl,pins = <
- MX6UL_PAD_NAND_WP_B__QSPI_A_SCLK 0x70a1
- MX6UL_PAD_NAND_READY_B__QSPI_A_DATA00 0x70a1
- MX6UL_PAD_NAND_CE0_B__QSPI_A_DATA01 0x70a1
- MX6UL_PAD_NAND_CE1_B__QSPI_A_DATA02 0x70a1
- MX6UL_PAD_NAND_CLE__QSPI_A_DATA03 0x70a1
- MX6UL_PAD_NAND_DQS__QSPI_A_SS0_B 0x70a1
- >;
- };
-
- pinctrl_reset_out: rstoutgrp {
- fsl,pins = <
- MX6UL_PAD_SNVS_TAMPER9__GPIO5_IO09 0x1b0b0
- >;
- };
-};
diff --git a/arch/arm/boot/dts/imx6ul-kontron-n6x1x-som-common.dtsi b/arch/arm/boot/dts/imx6ul-kontron-n6x1x-som-common.dtsi
new file mode 100644
index 000000000000..ba50c2966998
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-kontron-n6x1x-som-common.dtsi
@@ -0,0 +1,123 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2017 exceet electronics GmbH
+ * Copyright (C) 2018 Kontron Electronics GmbH
+ * Copyright (c) 2019 Krzysztof Kozlowski <krzk@kernel.org>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+
+&ecspi2 {
+ cs-gpios = <&gpio4 22 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi2>;
+ status = "okay";
+
+ spi-flash@0 {
+ compatible = "mxicy,mx25v8035f", "jedec,spi-nor";
+ spi-max-frequency = <50000000>;
+ reg = <0>;
+ };
+};
+
+&fec1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet1 &pinctrl_enet1_mdio>;
+ phy-mode = "rmii";
+ phy-handle = <ðphy1>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy1: ethernet-phy@1 {
+ reg = <1>;
+ micrel,led-mode = <0>;
+ clocks = <&clks IMX6UL_CLK_ENET_REF>;
+ clock-names = "rmii-ref";
+ };
+ };
+};
+
+&fec2 {
+ phy-mode = "rmii";
+ status = "disabled";
+};
+
+&qspi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_qspi>;
+ status = "okay";
+
+ spi-flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "spi-nand";
+ spi-max-frequency = <108000000>;
+ spi-tx-bus-width = <4>;
+ spi-rx-bus-width = <4>;
+ reg = <0>;
+
+ partition@0 {
+ label = "ubi1";
+ reg = <0x00000000 0x08000000>;
+ };
+
+ partition@8000000 {
+ label = "ubi2";
+ reg = <0x08000000 0x08000000>;
+ };
+ };
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reset_out>;
+
+ pinctrl_ecspi2: ecspi2grp {
+ fsl,pins = <
+ MX6UL_PAD_CSI_DATA03__ECSPI2_MISO 0x100b1
+ MX6UL_PAD_CSI_DATA02__ECSPI2_MOSI 0x100b1
+ MX6UL_PAD_CSI_DATA00__ECSPI2_SCLK 0x100b1
+ MX6UL_PAD_CSI_DATA01__GPIO4_IO22 0x100b1
+ >;
+ };
+
+ pinctrl_enet1: enet1grp {
+ fsl,pins = <
+ MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN 0x1b0b0
+ MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER 0x1b0b0
+ MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00 0x1b0b0
+ MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01 0x1b0b0
+ MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN 0x1b0b0
+ MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00 0x1b0b0
+ MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01 0x1b0b0
+ MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 0x4001b009
+ >;
+ };
+
+ pinctrl_enet1_mdio: enet1mdiogrp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO07__ENET1_MDC 0x1b0b0
+ MX6UL_PAD_GPIO1_IO06__ENET1_MDIO 0x1b0b0
+ >;
+ };
+
+ pinctrl_qspi: qspigrp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_WP_B__QSPI_A_SCLK 0x70a1
+ MX6UL_PAD_NAND_READY_B__QSPI_A_DATA00 0x70a1
+ MX6UL_PAD_NAND_CE0_B__QSPI_A_DATA01 0x70a1
+ MX6UL_PAD_NAND_CE1_B__QSPI_A_DATA02 0x70a1
+ MX6UL_PAD_NAND_CLE__QSPI_A_DATA03 0x70a1
+ MX6UL_PAD_NAND_DQS__QSPI_A_SS0_B 0x70a1
+ >;
+ };
+
+ pinctrl_reset_out: rstoutgrp {
+ fsl,pins = <
+ MX6UL_PAD_SNVS_TAMPER9__GPIO5_IO09 0x1b0b0
+ >;
+ };
+};
--
2.17.1
next prev parent reply other threads:[~2019-10-16 15:07 UTC|newest]
Thread overview: 24+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-10-16 15:06 [PATCH 00/10] Add support for more Kontron i.MX6UL/ULL SoMs and boards Schrempf Frieder
2019-10-16 15:07 ` Schrempf Frieder [this message]
2019-10-21 10:28 ` [PATCH 01/10] ARM: dts: imx6ul-kontron-n6310: Move common SoM nodes to a separate file krzk
2019-10-21 12:44 ` Schrempf Frieder
2019-10-16 15:07 ` [PATCH 02/10] ARM: dts: Add support for two more Kontron SoMs N6311 and N6411 Schrempf Frieder
2019-10-21 10:29 ` krzk
2019-10-16 15:07 ` [PATCH 03/10] ARM: dts: imx6ul-kontron-n6310-s: Move common nodes to a separate file Schrempf Frieder
2019-10-21 10:38 ` krzk
2019-10-21 12:44 ` Schrempf Frieder
2019-10-16 15:07 ` [PATCH 05/10] ARM: dts: imx6ul-kontron-n6x1x: Add 'chosen' node with 'stdout-path' Schrempf Frieder
2019-10-21 10:52 ` krzk
2019-10-16 15:07 ` [PATCH 04/10] ARM: dts: Add support for two more Kontron evalkit boards 'N6311 S' and 'N6411 S' Schrempf Frieder
2019-10-21 10:41 ` krzk
2019-10-16 15:07 ` [PATCH 08/10] ARM: dts: imx6ul-kontron-n6x1x-s: Remove an obsolete comment and fix indentation Schrempf Frieder
2019-10-16 15:07 ` [PATCH 06/10] ARM: dts: imx6ul-kontron-n6x1x-s: Specify bus-width for SD card and eMMC Schrempf Frieder
2019-10-16 15:07 ` [PATCH 07/10] ARM: dts: imx6ul-kontron-n6x1x-s: Add vbus-supply and overcurrent polarity to usb nodes Schrempf Frieder
2019-10-16 15:07 ` [PATCH 09/10] dt-bindings: arm: fsl: Add more Kontron i.MX6UL/ULL compatibles Schrempf Frieder
2019-10-21 10:44 ` krzk
2019-10-29 1:28 ` Rob Herring
2019-10-16 15:08 ` [PATCH 10/10] MAINTAINERS: Add an entry for Kontron Electronics ARM board support Schrempf Frieder
2019-10-17 8:14 ` [PATCH 00/10] Add support for more Kontron i.MX6UL/ULL SoMs and boards Marco Felsch
2019-10-17 8:24 ` Schrempf Frieder
2019-10-21 11:43 ` Marco Felsch
2019-10-21 12:24 ` Schrempf Frieder
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20191016150622.21753-2-frieder.schrempf@kontron.de \
--to=frieder.schrempf@kontron.de \
--cc=devicetree@vger.kernel.org \
--cc=festevam@gmail.com \
--cc=kernel@pengutronix.de \
--cc=krzk@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-imx@nxp.com \
--cc=linux-kernel@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=robh+dt@kernel.org \
--cc=s.hauer@pengutronix.de \
--cc=shawnguo@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).