From: Bjorn Andersson <bjorn.andersson@linaro.org>
To: Andy Gross <agross@kernel.org>, Rob Herring <robh+dt@kernel.org>,
Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org
Subject: [PATCH 06/11] arm64: dts: qcom: db820c: Sort all nodes
Date: Sun, 20 Oct 2019 22:13:17 -0700 [thread overview]
Message-ID: <20191021051322.297560-7-bjorn.andersson@linaro.org> (raw)
In-Reply-To: <20191021051322.297560-1-bjorn.andersson@linaro.org>
Sort all nodes in db820c.dtsi based on address, then name.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
---
arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi | 336 +++++++++----------
1 file changed, 168 insertions(+), 168 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi b/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi
index aed34a461b19..99990a139938 100644
--- a/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi
+++ b/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi
@@ -124,6 +124,18 @@
};
};
+&blsp1_i2c2 {
+ /* On Low speed expansion */
+ label = "LS-I2C0";
+ status = "okay";
+};
+
+&blsp1_spi0 {
+ /* On Low speed expansion */
+ label = "LS-SPI0";
+ status = "okay";
+};
+
&blsp1_uart1 {
label = "BT-UART";
status = "okay";
@@ -141,6 +153,24 @@
};
};
+&blsp2_i2c0 {
+ /* On High speed expansion */
+ label = "HS-I2C2";
+ status = "okay";
+};
+
+&blsp2_i2c1 {
+ /* On Low speed expansion */
+ label = "LS-I2C1";
+ status = "okay";
+};
+
+&blsp2_spi5 {
+ /* On High speed expansion */
+ label = "HS-SPI1";
+ status = "okay";
+};
+
&blsp2_uart1 {
label = "LS-UART1";
status = "okay";
@@ -157,75 +187,49 @@
pinctrl-1 = <&blsp2_uart2_4pins_sleep>;
};
-&blsp1_i2c2 {
- /* On Low speed expansion */
- label = "LS-I2C0";
- status = "okay";
+&camss {
+ vdda-supply = <&pm8994_l2>;
};
-&blsp2_i2c1 {
- /* On Low speed expansion */
- label = "LS-I2C1";
+&hdmi {
status = "okay";
-};
-&blsp1_spi0 {
- /* On Low speed expansion */
- label = "LS-SPI0";
- status = "okay";
-};
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&hdmi_hpd_active &hdmi_ddc_active>;
+ pinctrl-1 = <&hdmi_hpd_suspend &hdmi_ddc_suspend>;
-&blsp2_i2c0 {
- /* On High speed expansion */
- label = "HS-I2C2";
- status = "okay";
+ core-vdda-supply = <&pm8994_l12>;
+ core-vcc-supply = <&pm8994_s4>;
};
-&blsp2_spi5 {
- /* On High speed expansion */
- label = "HS-SPI1";
+&hdmi_phy {
status = "okay";
-};
-&camss {
- vdda-supply = <&pm8994_l2>;
+ vddio-supply = <&pm8994_l12>;
+ vcca-supply = <&pm8994_l28>;
+ #phy-cells = <0>;
};
-&sdhc2 {
- /* External SD card */
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>;
- pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>;
- cd-gpios = <&msmgpio 38 0x1>;
- vmmc-supply = <&pm8994_l21>;
- vqmmc-supply = <&pm8994_l13>;
+&hsusb_phy1 {
status = "okay";
+
+ vdda-pll-supply = <&pm8994_l12>;
+ vdda-phy-dpdm-supply = <&pm8994_l24>;
};
-&ufsphy {
+&hsusb_phy2 {
status = "okay";
- vdda-phy-supply = <&pm8994_l28>;
vdda-pll-supply = <&pm8994_l12>;
-
- vdda-phy-max-microamp = <18380>;
- vdda-pll-max-microamp = <9440>;
-
- vddp-ref-clk-supply = <&pm8994_l25>;
- vddp-ref-clk-max-microamp = <100>;
- vddp-ref-clk-always-on;
+ vdda-phy-dpdm-supply = <&pm8994_l24>;
};
-&ufshc {
+&mdp {
status = "okay";
+};
- vcc-supply = <&pm8994_l20>;
- vccq-supply = <&pm8994_l25>;
- vccq2-supply = <&pm8994_s4>;
-
- vcc-max-microamp = <600000>;
- vccq-max-microamp = <450000>;
- vccq2-max-microamp = <450000>;
+&mdss {
+ status = "okay";
};
&msmgpio {
@@ -382,6 +386,32 @@
"NC"; /* GPIO_149 */
};
+&pcie0 {
+ status = "okay";
+ perst-gpio = <&msmgpio 35 GPIO_ACTIVE_LOW>;
+ vddpe-3v3-supply = <&wlan_en>;
+ vdda-supply = <&pm8994_l28>;
+};
+
+&pcie1 {
+ status = "okay";
+ perst-gpio = <&msmgpio 130 GPIO_ACTIVE_LOW>;
+ vdda-supply = <&pm8994_l28>;
+};
+
+&pcie2 {
+ status = "okay";
+ perst-gpio = <&msmgpio 114 GPIO_ACTIVE_LOW>;
+ vdda-supply = <&pm8994_l28>;
+};
+
+&pcie_phy {
+ status = "okay";
+
+ vdda-phy-supply = <&pm8994_l28>;
+ vdda-pll-supply = <&pm8994_l12>;
+};
+
&pm8994_gpios {
gpio-line-names =
"NC",
@@ -434,114 +464,6 @@
"NC";
};
-&pcie_phy {
- status = "okay";
-
- vdda-phy-supply = <&pm8994_l28>;
- vdda-pll-supply = <&pm8994_l12>;
-};
-
-&usb3phy {
- status = "okay";
-
- vdda-phy-supply = <&pm8994_l28>;
- vdda-pll-supply = <&pm8994_l12>;
-
-};
-
-&hsusb_phy1 {
- status = "okay";
-
- vdda-pll-supply = <&pm8994_l12>;
- vdda-phy-dpdm-supply = <&pm8994_l24>;
-};
-
-&hsusb_phy2 {
- status = "okay";
-
- vdda-pll-supply = <&pm8994_l12>;
- vdda-phy-dpdm-supply = <&pm8994_l24>;
-};
-
-&usb3 {
- status = "okay";
- extcon = <&usb3_id>;
-
- dwc3@6a00000 {
- extcon = <&usb3_id>;
- dr_mode = "otg";
- };
-};
-
-&usb2 {
- status = "okay";
- extcon = <&usb2_id>;
-
- dwc3@7600000 {
- extcon = <&usb2_id>;
- dr_mode = "otg";
- maximum-speed = "high-speed";
- };
-};
-
-&pcie0 {
- status = "okay";
- perst-gpio = <&msmgpio 35 GPIO_ACTIVE_LOW>;
- vddpe-3v3-supply = <&wlan_en>;
- vdda-supply = <&pm8994_l28>;
-};
-
-&pcie1 {
- status = "okay";
- perst-gpio = <&msmgpio 130 GPIO_ACTIVE_LOW>;
- vdda-supply = <&pm8994_l28>;
-};
-
-&pcie2 {
- status = "okay";
- perst-gpio = <&msmgpio 114 GPIO_ACTIVE_LOW>;
- vdda-supply = <&pm8994_l28>;
-};
-
-&wcd9335 {
- clock-names = "mclk", "slimbus";
- clocks = <&div1_mclk>,
- <&rpmcc RPM_SMD_BB_CLK1>;
-
- vdd-buck-supply = <&pm8994_s4>;
- vdd-buck-sido-supply = <&pm8994_s4>;
- vdd-tx-supply = <&pm8994_s4>;
- vdd-rx-supply = <&pm8994_s4>;
- vdd-io-supply = <&pm8994_s4>;
-};
-
-&mdss {
- status = "okay";
-};
-
-&mdp {
- status = "okay";
-};
-
-&hdmi_phy {
- status = "okay";
-
- vddio-supply = <&pm8994_l12>;
- vcca-supply = <&pm8994_l28>;
- #phy-cells = <0>;
-};
-
-&hdmi {
- status = "okay";
-
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&hdmi_hpd_active &hdmi_ddc_active>;
- pinctrl-1 = <&hdmi_hpd_suspend &hdmi_ddc_suspend>;
-
- core-vdda-supply = <&pm8994_l12>;
- core-vcc-supply = <&pm8994_s4>;
-};
-
&rpm_requests {
pm8994-regulators {
compatible = "qcom,rpm-pm8994-regulators";
@@ -698,18 +620,15 @@
};
};
-&spmi_bus {
- pmic@0 {
- pon@800 {
- resin {
- compatible = "qcom,pm8941-resin";
- interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
- debounce = <15625>;
- bias-pull-up;
- linux,code = <KEY_VOLUMEDOWN>;
- };
- };
- };
+&sdhc2 {
+ /* External SD card */
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>;
+ pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>;
+ cd-gpios = <&msmgpio 38 0x1>;
+ vmmc-supply = <&pm8994_l21>;
+ vqmmc-supply = <&pm8994_l13>;
+ status = "okay";
};
&sound {
@@ -783,3 +702,84 @@
};
};
};
+
+&spmi_bus {
+ pmic@0 {
+ pon@800 {
+ resin {
+ compatible = "qcom,pm8941-resin";
+ interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
+ debounce = <15625>;
+ bias-pull-up;
+ linux,code = <KEY_VOLUMEDOWN>;
+ };
+ };
+ };
+};
+
+&ufsphy {
+ status = "okay";
+
+ vdda-phy-supply = <&pm8994_l28>;
+ vdda-pll-supply = <&pm8994_l12>;
+
+ vdda-phy-max-microamp = <18380>;
+ vdda-pll-max-microamp = <9440>;
+
+ vddp-ref-clk-supply = <&pm8994_l25>;
+ vddp-ref-clk-max-microamp = <100>;
+ vddp-ref-clk-always-on;
+};
+
+&ufshc {
+ status = "okay";
+
+ vcc-supply = <&pm8994_l20>;
+ vccq-supply = <&pm8994_l25>;
+ vccq2-supply = <&pm8994_s4>;
+
+ vcc-max-microamp = <600000>;
+ vccq-max-microamp = <450000>;
+ vccq2-max-microamp = <450000>;
+};
+
+&usb2 {
+ status = "okay";
+ extcon = <&usb2_id>;
+
+ dwc3@7600000 {
+ extcon = <&usb2_id>;
+ dr_mode = "otg";
+ maximum-speed = "high-speed";
+ };
+};
+
+&usb3 {
+ status = "okay";
+ extcon = <&usb3_id>;
+
+ dwc3@6a00000 {
+ extcon = <&usb3_id>;
+ dr_mode = "otg";
+ };
+};
+
+&usb3phy {
+ status = "okay";
+
+ vdda-phy-supply = <&pm8994_l28>;
+ vdda-pll-supply = <&pm8994_l12>;
+
+};
+
+&wcd9335 {
+ clock-names = "mclk", "slimbus";
+ clocks = <&div1_mclk>,
+ <&rpmcc RPM_SMD_BB_CLK1>;
+
+ vdd-buck-supply = <&pm8994_s4>;
+ vdd-buck-sido-supply = <&pm8994_s4>;
+ vdd-tx-supply = <&pm8994_s4>;
+ vdd-rx-supply = <&pm8994_s4>;
+ vdd-io-supply = <&pm8994_s4>;
+};
--
2.23.0
next prev parent reply other threads:[~2019-10-21 5:13 UTC|newest]
Thread overview: 15+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-10-21 5:13 [PATCH 00/11] arm64: dts: qcom: msm8996: Introduce IFC6640 Bjorn Andersson
2019-10-21 5:13 ` [PATCH 01/11] arm64: dts: qcom: db820c: Move non-soc entries out of /soc Bjorn Andersson
2019-10-21 5:13 ` [PATCH 02/11] arm64: dts: qcom: msm8996: Use node references in db820c Bjorn Andersson
2019-10-21 5:13 ` [PATCH 03/11] arm64: dts: qcom: msm8996: Move regulator consumers to db820c Bjorn Andersson
2019-10-21 5:13 ` [PATCH 04/11] arm64: dts: qcom: msm8996: Move regulators " Bjorn Andersson
2019-10-21 5:13 ` [PATCH 05/11] arm64: dts: qcom: db820c: Group root nodes Bjorn Andersson
2019-10-21 5:13 ` Bjorn Andersson [this message]
2019-10-21 5:13 ` [PATCH 07/11] arm64: dts: qcom: db820c: Remove pin specific files Bjorn Andersson
2019-10-21 5:13 ` [PATCH 08/11] arm64: dts: qcom: msm8996: Pad addresses Bjorn Andersson
2019-10-21 5:13 ` [PATCH 09/11] arm64: dts: qcom: msm8996: Sort all nodes in msm8996.dtsi Bjorn Andersson
2019-10-21 5:13 ` [PATCH 10/11] arm64: dts: qcom: db820c: Use regulator names from schematics Bjorn Andersson
2019-10-21 5:13 ` [PATCH 11/11] arm64: dts: qcom: msm8996: Introduce IFC6640 Bjorn Andersson
2019-11-03 8:13 ` [PATCH 00/11] " Vinod Koul
2019-11-04 4:55 ` Bjorn Andersson
2019-11-04 9:27 ` Vinod Koul
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20191021051322.297560-7-bjorn.andersson@linaro.org \
--to=bjorn.andersson@linaro.org \
--cc=agross@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).