From: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
To: rubini@gnudd.com, hch@infradead.org,
linux-kernel@vger.kernel.org,
Thomas Gleixner <tglx@linutronix.de>,
Ingo Molnar <mingo@redhat.com>, Borislav Petkov <bp@alien8.de>,
"H. Peter Anvin" <hpa@zytor.com>,
x86@kernel.org, Bjorn Helgaas <bhelgaas@google.com>
Cc: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>,
Christoph Hellwig <hch@lst.de>,
linux-pci@vger.kernel.org
Subject: [PATCH v3 2/2] x86/PCI: sta2x11: use default DMA address translation
Date: Thu, 7 Nov 2019 16:06:45 +0100 [thread overview]
Message-ID: <20191107150646.13485-3-nsaenzjulienne@suse.de> (raw)
In-Reply-To: <20191107150646.13485-1-nsaenzjulienne@suse.de>
The devices found behind this PCIe chip have unusual DMA mapping
constraints as there is an AMBA interconnect placed in between them and
the different PCI endpoints. The offset between physical memory
addresses and AMBA's view is provided by reading a PCI config register,
which is saved and used whenever DMA mapping is needed.
It turns out that this DMA setup can be represented by properly setting
'dma_pfn_offset', 'dma_bus_mask' and 'dma_mask' during the PCI device
enable fixup. And ultimately allows us to get rid of this device's
custom DMA functions.
Aside from the code deletion and DMA setup, sta2x11_pdev_to_mapping() is
moved to avoid warnings whenever CONFIG_PM is not enabled.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
---
Changed since v1:
- use variable to avoid recalculating AMBA's max address
- remove x86's dma-direct.h as it's not longer needed
arch/x86/Kconfig | 1 -
arch/x86/include/asm/device.h | 3 -
arch/x86/include/asm/dma-direct.h | 9 --
arch/x86/pci/sta2x11-fixup.c | 135 ++++++------------------------
4 files changed, 26 insertions(+), 122 deletions(-)
delete mode 100644 arch/x86/include/asm/dma-direct.h
diff --git a/arch/x86/Kconfig b/arch/x86/Kconfig
index 45699e458057..d67bdf00e2ab 100644
--- a/arch/x86/Kconfig
+++ b/arch/x86/Kconfig
@@ -708,7 +708,6 @@ config X86_SUPPORTS_MEMORY_FAILURE
config STA2X11
bool "STA2X11 Companion Chip Support"
depends on X86_32_NON_STANDARD && PCI
- select ARCH_HAS_PHYS_TO_DMA
select SWIOTLB
select MFD_STA2X11
select GPIOLIB
diff --git a/arch/x86/include/asm/device.h b/arch/x86/include/asm/device.h
index a8f6c809d9b1..5e12c63b47aa 100644
--- a/arch/x86/include/asm/device.h
+++ b/arch/x86/include/asm/device.h
@@ -6,9 +6,6 @@ struct dev_archdata {
#if defined(CONFIG_INTEL_IOMMU) || defined(CONFIG_AMD_IOMMU)
void *iommu; /* hook for IOMMU specific extension */
#endif
-#ifdef CONFIG_STA2X11
- bool is_sta2x11;
-#endif
};
#if defined(CONFIG_X86_DEV_DMA_OPS) && defined(CONFIG_PCI_DOMAINS)
diff --git a/arch/x86/include/asm/dma-direct.h b/arch/x86/include/asm/dma-direct.h
deleted file mode 100644
index 1a19251eaac9..000000000000
--- a/arch/x86/include/asm/dma-direct.h
+++ /dev/null
@@ -1,9 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-#ifndef ASM_X86_DMA_DIRECT_H
-#define ASM_X86_DMA_DIRECT_H 1
-
-bool dma_capable(struct device *dev, dma_addr_t addr, size_t size);
-dma_addr_t __phys_to_dma(struct device *dev, phys_addr_t paddr);
-phys_addr_t __dma_to_phys(struct device *dev, dma_addr_t daddr);
-
-#endif /* ASM_X86_DMA_DIRECT_H */
diff --git a/arch/x86/pci/sta2x11-fixup.c b/arch/x86/pci/sta2x11-fixup.c
index 6269a175385d..4a631264b809 100644
--- a/arch/x86/pci/sta2x11-fixup.c
+++ b/arch/x86/pci/sta2x11-fixup.c
@@ -30,7 +30,6 @@ struct sta2x11_ahb_regs { /* saved during suspend */
};
struct sta2x11_mapping {
- u32 amba_base;
int is_suspended;
struct sta2x11_ahb_regs regs[STA2X11_NR_FUNCS];
};
@@ -92,18 +91,6 @@ static int sta2x11_pdev_to_ep(struct pci_dev *pdev)
return pdev->bus->number - instance->bus0;
}
-static struct sta2x11_mapping *sta2x11_pdev_to_mapping(struct pci_dev *pdev)
-{
- struct sta2x11_instance *instance;
- int ep;
-
- instance = sta2x11_pdev_to_instance(pdev);
- if (!instance)
- return NULL;
- ep = sta2x11_pdev_to_ep(pdev);
- return instance->map + ep;
-}
-
/* This is exported, as some devices need to access the MFD registers */
struct sta2x11_instance *sta2x11_get_instance(struct pci_dev *pdev)
{
@@ -111,39 +98,6 @@ struct sta2x11_instance *sta2x11_get_instance(struct pci_dev *pdev)
}
EXPORT_SYMBOL(sta2x11_get_instance);
-
-/**
- * p2a - Translate physical address to STA2x11 AMBA address,
- * used for DMA transfers to STA2x11
- * @p: Physical address
- * @pdev: PCI device (must be hosted within the connext)
- */
-static dma_addr_t p2a(dma_addr_t p, struct pci_dev *pdev)
-{
- struct sta2x11_mapping *map;
- dma_addr_t a;
-
- map = sta2x11_pdev_to_mapping(pdev);
- a = p + map->amba_base;
- return a;
-}
-
-/**
- * a2p - Translate STA2x11 AMBA address to physical address
- * used for DMA transfers from STA2x11
- * @a: STA2x11 AMBA address
- * @pdev: PCI device (must be hosted within the connext)
- */
-static dma_addr_t a2p(dma_addr_t a, struct pci_dev *pdev)
-{
- struct sta2x11_mapping *map;
- dma_addr_t p;
-
- map = sta2x11_pdev_to_mapping(pdev);
- p = a - map->amba_base;
- return p;
-}
-
/* At setup time, we use our own ops if the device is a ConneXt one */
static void sta2x11_setup_pdev(struct pci_dev *pdev)
{
@@ -151,70 +105,12 @@ static void sta2x11_setup_pdev(struct pci_dev *pdev)
if (!instance) /* either a sta2x11 bridge or another ST device */
return;
- pci_set_consistent_dma_mask(pdev, STA2X11_AMBA_SIZE - 1);
- pci_set_dma_mask(pdev, STA2X11_AMBA_SIZE - 1);
- pdev->dev.archdata.is_sta2x11 = true;
/* We must enable all devices as master, for audio DMA to work */
pci_set_master(pdev);
}
DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_STMICRO, PCI_ANY_ID, sta2x11_setup_pdev);
-/*
- * The following three functions are exported (used in swiotlb: FIXME)
- */
-/**
- * dma_capable - Check if device can manage DMA transfers (FIXME: kill it)
- * @dev: device for a PCI device
- * @addr: DMA address
- * @size: DMA size
- */
-bool dma_capable(struct device *dev, dma_addr_t addr, size_t size)
-{
- struct sta2x11_mapping *map;
-
- if (!dev->archdata.is_sta2x11) {
- if (!dev->dma_mask)
- return false;
- return addr + size - 1 <= *dev->dma_mask;
- }
-
- map = sta2x11_pdev_to_mapping(to_pci_dev(dev));
-
- if (!map || (addr < map->amba_base))
- return false;
- if (addr + size >= map->amba_base + STA2X11_AMBA_SIZE) {
- return false;
- }
-
- return true;
-}
-
-/**
- * __phys_to_dma - Return the DMA AMBA address used for this STA2x11 device
- * @dev: device for a PCI device
- * @paddr: Physical address
- */
-dma_addr_t __phys_to_dma(struct device *dev, phys_addr_t paddr)
-{
- if (!dev->archdata.is_sta2x11)
- return paddr;
- return p2a(paddr, to_pci_dev(dev));
-}
-
-/**
- * dma_to_phys - Return the physical address used for this STA2x11 DMA address
- * @dev: device for a PCI device
- * @daddr: STA2x11 AMBA DMA address
- */
-phys_addr_t __dma_to_phys(struct device *dev, dma_addr_t daddr)
-{
- if (!dev->archdata.is_sta2x11)
- return daddr;
- return a2p(daddr, to_pci_dev(dev));
-}
-
-
/*
* At boot we must set up the mappings for the pcie-to-amba bridge.
* It involves device access, and the same happens at suspend/resume time
@@ -234,12 +130,22 @@ phys_addr_t __dma_to_phys(struct device *dev, dma_addr_t daddr)
/* At probe time, enable mapping for each endpoint, using the pdev */
static void sta2x11_map_ep(struct pci_dev *pdev)
{
- struct sta2x11_mapping *map = sta2x11_pdev_to_mapping(pdev);
+ struct sta2x11_instance *instance = sta2x11_pdev_to_instance(pdev);
+ struct device *dev = &pdev->dev;
+ u32 amba_base, max_amba_addr;
int i;
- if (!map)
+ if (!instance)
return;
- pci_read_config_dword(pdev, AHB_BASE(0), &map->amba_base);
+
+ pci_read_config_dword(pdev, AHB_BASE(0), &amba_base);
+ max_amba_addr = amba_base + STA2X11_AMBA_SIZE - 1;
+
+ dev->dma_pfn_offset = PFN_DOWN(-amba_base);
+
+ dev->bus_dma_mask = max_amba_addr;
+ pci_set_consistent_dma_mask(pdev, max_amba_addr);
+ pci_set_dma_mask(pdev, max_amba_addr);
/* Configure AHB mapping */
pci_write_config_dword(pdev, AHB_PEXLBASE(0), 0);
@@ -253,13 +159,24 @@ static void sta2x11_map_ep(struct pci_dev *pdev)
dev_info(&pdev->dev,
"sta2x11: Map EP %i: AMBA address %#8x-%#8x\n",
- sta2x11_pdev_to_ep(pdev), map->amba_base,
- map->amba_base + STA2X11_AMBA_SIZE - 1);
+ sta2x11_pdev_to_ep(pdev), amba_base, max_amba_addr);
}
DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_STMICRO, PCI_ANY_ID, sta2x11_map_ep);
#ifdef CONFIG_PM /* Some register values must be saved and restored */
+static struct sta2x11_mapping *sta2x11_pdev_to_mapping(struct pci_dev *pdev)
+{
+ struct sta2x11_instance *instance;
+ int ep;
+
+ instance = sta2x11_pdev_to_instance(pdev);
+ if (!instance)
+ return NULL;
+ ep = sta2x11_pdev_to_ep(pdev);
+ return instance->map + ep;
+}
+
static void suspend_mapping(struct pci_dev *pdev)
{
struct sta2x11_mapping *map = sta2x11_pdev_to_mapping(pdev);
--
2.23.0
next prev parent reply other threads:[~2019-11-07 15:07 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-11-07 15:06 [PATCH v3 0/2] x86: Get rid of custom DMA functions Nicolas Saenz Julienne
2019-11-07 15:06 ` [PATCH v3 1/2] dma-direct: check for overflows on 32 bit DMA addresses Nicolas Saenz Julienne
2019-11-07 15:06 ` Nicolas Saenz Julienne [this message]
2019-11-13 18:54 ` [PATCH v3 2/2] x86/PCI: sta2x11: use default DMA address translation Borislav Petkov
2019-11-14 7:29 ` Christoph Hellwig
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20191107150646.13485-3-nsaenzjulienne@suse.de \
--to=nsaenzjulienne@suse.de \
--cc=bhelgaas@google.com \
--cc=bp@alien8.de \
--cc=hch@infradead.org \
--cc=hch@lst.de \
--cc=hpa@zytor.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pci@vger.kernel.org \
--cc=mingo@redhat.com \
--cc=rubini@gnudd.com \
--cc=tglx@linutronix.de \
--cc=x86@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).