[RESEND Patch v3 01/20] dt-bindings: media: cal: update binding to use syscon

From: Benoit Parrot <bparrot@ti.com>
To: Hans Verkuil <hverkuil@xs4all.nl>,
	Sakari Ailus <sakari.ailus@linux.intel.com>,
	Rob Herring <robh+dt@kernel.org>
Cc: <linux-media@vger.kernel.org>, <devicetree@vger.kernel.org>,
	<linux-kernel@vger.kernel.org>, Benoit Parrot <bparrot@ti.com>
Subject: [RESEND Patch v3 01/20] dt-bindings: media: cal: update binding to use syscon
Date: Tue, 12 Nov 2019 08:53:28 -0600	[thread overview]
Message-ID: <20191112145347.23519-2-bparrot@ti.com> (raw)
In-Reply-To: <20191112145347.23519-1-bparrot@ti.com>

Update Device Tree bindings for the CAL driver to use syscon to access
the phy config register instead of trying to map it directly.

Signed-off-by: Benoit Parrot <bparrot@ti.com>
---
 Documentation/devicetree/bindings/media/ti-cal.txt | 14 +++++++++-----
 1 file changed, 9 insertions(+), 5 deletions(-)

diff --git a/Documentation/devicetree/bindings/media/ti-cal.txt b/Documentation/devicetree/bindings/media/ti-cal.txt
index ae9b52f37576..93096d924786 100644
--- a/Documentation/devicetree/bindings/media/ti-cal.txt
+++ b/Documentation/devicetree/bindings/media/ti-cal.txt
@@ -10,9 +10,14 @@ Required properties:
 - compatible: must be "ti,dra72-cal"
 - reg:	CAL Top level, Receiver Core #0, Receiver Core #1 and Camera RX
 	control address space
-- reg-names: cal_top, cal_rx_core0, cal_rx_core1, and camerrx_control
+- reg-names: cal_top, cal_rx_core0, cal_rx_core1 and camerrx_control
 	     registers
 - interrupts: should contain IRQ line for the CAL;
+- ti,camerrx-control: phandle to the device control module and offset to
+		      the control_camerarx_core register.
+		      This node is meant to replace the "camerrx_control"
+		      reg entry above but "camerrx_control" is still
+		      handled for backward compatibility.
 
 CAL supports 2 camera port nodes on MIPI bus. Each CSI2 camera port nodes
 should contain a 'port' child node with child 'endpoint' node. Please
@@ -25,13 +30,12 @@ Example:
 		ti,hwmods = "cal";
 		reg = <0x4845B000 0x400>,
 		      <0x4845B800 0x40>,
-		      <0x4845B900 0x40>,
-		      <0x4A002e94 0x4>;
+		      <0x4845B900 0x40>;
 		reg-names = "cal_top",
 			    "cal_rx_core0",
-			    "cal_rx_core1",
-			    "camerrx_control";
+			    "cal_rx_core1";
 		interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>;
+		ti,camerrx-control = <&scm_conf 0xE94>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-- 
2.17.1

