From: Beniamin Bia <beniamin.bia@analog.com>
To: <jic23@kernel.org>
Cc: <lars@metafoo.de>, <Michael.Hennerich@analog.com>,
<pmeerw@pmeerw.net>, <gregkh@linuxfoundation.org>,
<linux-iio@vger.kernel.org>, <devel@driverdev.osuosl.org>,
<linux-kernel@vger.kernel.org>, <mark.rutland@arm.com>,
<devicetree@vger.kernel.org>, <biabeniamin@outlook.com>,
<knaack.h@gmx.de>, <robh+dt@kernel.org>,
Paul Cercueil <paul.cercueil@analog.com>,
Beniamin Bia <beniamin.bia@analog.com>
Subject: [PATCH v4 2/4] iio: adc: ad7091r5: Add scale and external VREF support
Date: Fri, 15 Nov 2019 14:23:14 +0200 [thread overview]
Message-ID: <20191115122316.20893-2-beniamin.bia@analog.com> (raw)
In-Reply-To: <20191115122316.20893-1-beniamin.bia@analog.com>
From: Paul Cercueil <paul.cercueil@analog.com>
The scale can now be obtained with the "in_voltage_scale" file.
By default, the scale returned corresponds to the internal VREF of 2.5V.
It is possible to use an external VREF (through the REFIN/REFOUT pin of
the chip), by passing a regulator to the driver. The scale will then be
calculated according to the voltage reported by the regulator.
Signed-off-by: Paul Cercueil <paul.cercueil@analog.com>
Co-developed-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
---
Changes in v4:
-reg renamed to vref
-add ad7091r_remove only on successful reg enable
drivers/iio/adc/ad7091r-base.c | 39 ++++++++++++++++++++++++++++++++++
drivers/iio/adc/ad7091r-base.h | 1 +
drivers/iio/adc/ad7091r5.c | 5 +++++
3 files changed, 45 insertions(+)
diff --git a/drivers/iio/adc/ad7091r-base.c b/drivers/iio/adc/ad7091r-base.c
index 854de7c654c2..6e2b6d3f2aa9 100644
--- a/drivers/iio/adc/ad7091r-base.c
+++ b/drivers/iio/adc/ad7091r-base.c
@@ -11,6 +11,7 @@
#include <linux/interrupt.h>
#include <linux/module.h>
#include <linux/regmap.h>
+#include <linux/regulator/consumer.h>
#include "ad7091r-base.h"
@@ -42,6 +43,7 @@ enum ad7091r_mode {
struct ad7091r_state {
struct device *dev;
struct regmap *map;
+ struct regulator *vref;
const struct ad7091r_chip_info *chip_info;
enum ad7091r_mode mode;
struct mutex lock; /*lock to prevent concurent reads */
@@ -141,6 +143,21 @@ static int ad7091r_read_raw(struct iio_dev *iio_dev,
ret = IIO_VAL_INT;
break;
+ case IIO_CHAN_INFO_SCALE:
+ if (st->vref) {
+ ret = regulator_get_voltage(st->vref);
+ if (ret < 0)
+ goto unlock;
+
+ *val = ret / 1000;
+ } else {
+ *val = st->chip_info->vref_mV;
+ }
+
+ *val2 = chan->scan_type.realbits;
+ ret = IIO_VAL_FRACTIONAL_LOG2;
+ break;
+
default:
ret = -EINVAL;
break;
@@ -183,6 +200,13 @@ static irqreturn_t ad7091r_event_handler(int irq, void *private)
return IRQ_HANDLED;
}
+static void ad7091r_remove(void *data)
+{
+ struct ad7091r_state *st = data;
+
+ regulator_disable(st->vref);
+}
+
int ad7091r_probe(struct device *dev, const char *name,
const struct ad7091r_chip_info *chip_info,
struct regmap *map, int irq)
@@ -216,6 +240,21 @@ int ad7091r_probe(struct device *dev, const char *name,
return ret;
}
+ st->vref = devm_regulator_get_optional(dev, "vref");
+ if (IS_ERR(st->vref)) {
+ if (PTR_ERR(st->vref) == EPROBE_DEFER)
+ return -EPROBE_DEFER;
+
+ st->vref = NULL;
+ } else {
+ ret = regulator_enable(st->vref);
+ if (ret)
+ return ret;
+ ret = devm_add_action_or_reset(dev, ad7091r_remove, st);
+ if (ret)
+ return ret;
+ }
+
/* Use command mode by default to convert only desired channels*/
ret = ad7091r_set_mode(st, AD7091R_MODE_COMMAND);
if (ret)
diff --git a/drivers/iio/adc/ad7091r-base.h b/drivers/iio/adc/ad7091r-base.h
index b0b4fe01a681..509748aef9b1 100644
--- a/drivers/iio/adc/ad7091r-base.h
+++ b/drivers/iio/adc/ad7091r-base.h
@@ -14,6 +14,7 @@ struct ad7091r_state;
struct ad7091r_chip_info {
unsigned int num_channels;
const struct iio_chan_spec *channels;
+ unsigned int vref_mV;
};
extern const struct regmap_config ad7091r_regmap_config;
diff --git a/drivers/iio/adc/ad7091r5.c b/drivers/iio/adc/ad7091r5.c
index 30ff0108a6ed..9665679c3ea6 100644
--- a/drivers/iio/adc/ad7091r5.c
+++ b/drivers/iio/adc/ad7091r5.c
@@ -35,10 +35,13 @@ static const struct iio_event_spec ad7091r5_events[] = {
#define AD7091R_CHANNEL(idx, bits, ev, num_ev) { \
.type = IIO_VOLTAGE, \
.info_mask_separate = BIT(IIO_CHAN_INFO_RAW), \
+ .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), \
.indexed = 1, \
.channel = idx, \
.event_spec = ev, \
.num_event_specs = num_ev, \
+ .scan_type.storagebits = 16, \
+ .scan_type.realbits = bits, \
}
static const struct iio_chan_spec ad7091r5_channels_irq[] = {
AD7091R_CHANNEL(0, 12, ad7091r5_events, ARRAY_SIZE(ad7091r5_events)),
@@ -57,11 +60,13 @@ static const struct iio_chan_spec ad7091r5_channels_noirq[] = {
static const struct ad7091r_chip_info ad7091r5_chip_info_irq = {
.channels = ad7091r5_channels_irq,
.num_channels = ARRAY_SIZE(ad7091r5_channels_irq),
+ .vref_mV = 2500,
};
static const struct ad7091r_chip_info ad7091r5_chip_info_noirq = {
.channels = ad7091r5_channels_noirq,
.num_channels = ARRAY_SIZE(ad7091r5_channels_noirq),
+ .vref_mV = 2500,
};
static int ad7091r5_i2c_probe(struct i2c_client *i2c,
--
2.17.1
next prev parent reply other threads:[~2019-11-15 12:23 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-11-15 12:23 [PATCH v4 1/4] iio: adc: Add support for AD7091R5 ADC Beniamin Bia
2019-11-15 12:23 ` Beniamin Bia [this message]
2019-11-15 13:03 ` [PATCH v4 2/4] iio: adc: ad7091r5: Add scale and external VREF support Dan Carpenter
2019-11-15 12:23 ` [PATCH v4 3/4] dt-binding: iio: Add documentation for AD7091R5 Beniamin Bia
2019-11-15 12:23 ` [PATCH v4 4/4] MAINTAINERS: add entry for AD7091R5 driver Beniamin Bia
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20191115122316.20893-2-beniamin.bia@analog.com \
--to=beniamin.bia@analog.com \
--cc=Michael.Hennerich@analog.com \
--cc=biabeniamin@outlook.com \
--cc=devel@driverdev.osuosl.org \
--cc=devicetree@vger.kernel.org \
--cc=gregkh@linuxfoundation.org \
--cc=jic23@kernel.org \
--cc=knaack.h@gmx.de \
--cc=lars@metafoo.de \
--cc=linux-iio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=paul.cercueil@analog.com \
--cc=pmeerw@pmeerw.net \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).