linux-kernel.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Beniamin Bia <beniamin.bia@analog.com>
To: <jic23@kernel.org>
Cc: <lars@metafoo.de>, <Michael.Hennerich@analog.com>,
	<pmeerw@pmeerw.net>, <gregkh@linuxfoundation.org>,
	<linux-iio@vger.kernel.org>, <devel@driverdev.osuosl.org>,
	<linux-kernel@vger.kernel.org>, <mark.rutland@arm.com>,
	<devicetree@vger.kernel.org>, <biabeniamin@outlook.com>,
	<knaack.h@gmx.de>, <robh+dt@kernel.org>,
	Paul Cercueil <paul.cercueil@analog.com>,
	Beniamin Bia <beniamin.bia@analog.com>
Subject: [PATCH v5 2/4] iio: adc: ad7091r5: Add scale and external VREF support
Date: Fri, 15 Nov 2019 15:57:21 +0200	[thread overview]
Message-ID: <20191115135723.12219-2-beniamin.bia@analog.com> (raw)
In-Reply-To: <20191115135723.12219-1-beniamin.bia@analog.com>

From: Paul Cercueil <paul.cercueil@analog.com>

The scale can now be obtained with the "in_voltage_scale" file.
By default, the scale returned corresponds to the internal VREF of 2.5V.

It is possible to use an external VREF (through the REFIN/REFOUT pin of
the chip), by passing a regulator to the driver. The scale will then be
calculated according to the voltage reported by the regulator.

Signed-off-by: Paul Cercueil <paul.cercueil@analog.com>
Co-developed-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
---
Changes in v5:
-check if error is -eprobe instead of eprobe
-one bracket aligned

 drivers/iio/adc/ad7091r-base.c | 38 ++++++++++++++++++++++++++++++++++
 drivers/iio/adc/ad7091r-base.h |  1 +
 drivers/iio/adc/ad7091r5.c     |  5 +++++
 3 files changed, 44 insertions(+)

diff --git a/drivers/iio/adc/ad7091r-base.c b/drivers/iio/adc/ad7091r-base.c
index 854de7c654c2..58fcf1ff8c76 100644
--- a/drivers/iio/adc/ad7091r-base.c
+++ b/drivers/iio/adc/ad7091r-base.c
@@ -11,6 +11,7 @@
 #include <linux/interrupt.h>
 #include <linux/module.h>
 #include <linux/regmap.h>
+#include <linux/regulator/consumer.h>
 
 #include "ad7091r-base.h"
 
@@ -42,6 +43,7 @@ enum ad7091r_mode {
 struct ad7091r_state {
 	struct device *dev;
 	struct regmap *map;
+	struct regulator *vref;
 	const struct ad7091r_chip_info *chip_info;
 	enum ad7091r_mode mode;
 	struct mutex lock; /*lock to prevent concurent reads */
@@ -141,6 +143,21 @@ static int ad7091r_read_raw(struct iio_dev *iio_dev,
 		ret = IIO_VAL_INT;
 		break;
 
+	case IIO_CHAN_INFO_SCALE:
+		if (st->vref) {
+			ret = regulator_get_voltage(st->vref);
+			if (ret < 0)
+				goto unlock;
+
+			*val = ret / 1000;
+		} else {
+			*val = st->chip_info->vref_mV;
+		}
+
+		*val2 = chan->scan_type.realbits;
+		ret = IIO_VAL_FRACTIONAL_LOG2;
+		break;
+
 	default:
 		ret = -EINVAL;
 		break;
@@ -183,6 +200,13 @@ static irqreturn_t ad7091r_event_handler(int irq, void *private)
 	return IRQ_HANDLED;
 }
 
+static void ad7091r_remove(void *data)
+{
+	struct ad7091r_state *st = data;
+
+	regulator_disable(st->vref);
+}
+
 int ad7091r_probe(struct device *dev, const char *name,
 		const struct ad7091r_chip_info *chip_info,
 		struct regmap *map, int irq)
@@ -216,6 +240,20 @@ int ad7091r_probe(struct device *dev, const char *name,
 			return ret;
 	}
 
+	st->vref = devm_regulator_get_optional(dev, "vref");
+	if (IS_ERR(st->vref)) {
+		if (PTR_ERR(st->reg) == -EPROBE_DEFER)
+			return -EPROBE_DEFER;
+		st->vref = NULL;
+	} else {
+		ret = regulator_enable(st->vref);
+		if (ret)
+			return ret;
+		ret = devm_add_action_or_reset(dev, ad7091r_remove, st);
+		if (ret)
+			return ret;
+	}
+
 	/* Use command mode by default to convert only desired channels*/
 	ret = ad7091r_set_mode(st, AD7091R_MODE_COMMAND);
 	if (ret)
diff --git a/drivers/iio/adc/ad7091r-base.h b/drivers/iio/adc/ad7091r-base.h
index b0b4fe01a681..509748aef9b1 100644
--- a/drivers/iio/adc/ad7091r-base.h
+++ b/drivers/iio/adc/ad7091r-base.h
@@ -14,6 +14,7 @@ struct ad7091r_state;
 struct ad7091r_chip_info {
 	unsigned int num_channels;
 	const struct iio_chan_spec *channels;
+	unsigned int vref_mV;
 };
 
 extern const struct regmap_config ad7091r_regmap_config;
diff --git a/drivers/iio/adc/ad7091r5.c b/drivers/iio/adc/ad7091r5.c
index 30ff0108a6ed..9665679c3ea6 100644
--- a/drivers/iio/adc/ad7091r5.c
+++ b/drivers/iio/adc/ad7091r5.c
@@ -35,10 +35,13 @@ static const struct iio_event_spec ad7091r5_events[] = {
 #define AD7091R_CHANNEL(idx, bits, ev, num_ev) { \
 	.type = IIO_VOLTAGE, \
 	.info_mask_separate = BIT(IIO_CHAN_INFO_RAW), \
+	.info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), \
 	.indexed = 1, \
 	.channel = idx, \
 	.event_spec = ev, \
 	.num_event_specs = num_ev, \
+	.scan_type.storagebits = 16, \
+	.scan_type.realbits = bits, \
 }
 static const struct iio_chan_spec ad7091r5_channels_irq[] = {
 	AD7091R_CHANNEL(0, 12, ad7091r5_events, ARRAY_SIZE(ad7091r5_events)),
@@ -57,11 +60,13 @@ static const struct iio_chan_spec ad7091r5_channels_noirq[] = {
 static const struct ad7091r_chip_info ad7091r5_chip_info_irq = {
 	.channels = ad7091r5_channels_irq,
 	.num_channels = ARRAY_SIZE(ad7091r5_channels_irq),
+	.vref_mV = 2500,
 };
 
 static const struct ad7091r_chip_info ad7091r5_chip_info_noirq = {
 	.channels = ad7091r5_channels_noirq,
 	.num_channels = ARRAY_SIZE(ad7091r5_channels_noirq),
+	.vref_mV = 2500,
 };
 
 static int ad7091r5_i2c_probe(struct i2c_client *i2c,
-- 
2.17.1


  reply	other threads:[~2019-11-15 13:57 UTC|newest]

Thread overview: 8+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-11-15 13:57 [PATCH v5 1/4] iio: adc: Add support for AD7091R5 ADC Beniamin Bia
2019-11-15 13:57 ` Beniamin Bia [this message]
2019-11-16 17:06   ` [PATCH v5 2/4] iio: adc: ad7091r5: Add scale and external VREF support Jonathan Cameron
2019-11-15 13:57 ` [PATCH v5 3/4] dt-binding: iio: Add documentation for AD7091R5 Beniamin Bia
2019-11-16 17:10   ` Jonathan Cameron
2019-11-15 13:57 ` [PATCH v5 4/4] MAINTAINERS: add entry for AD7091R5 driver Beniamin Bia
2019-11-16 17:11   ` Jonathan Cameron
2019-11-16 16:58 ` [PATCH v5 1/4] iio: adc: Add support for AD7091R5 ADC Jonathan Cameron

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20191115135723.12219-2-beniamin.bia@analog.com \
    --to=beniamin.bia@analog.com \
    --cc=Michael.Hennerich@analog.com \
    --cc=biabeniamin@outlook.com \
    --cc=devel@driverdev.osuosl.org \
    --cc=devicetree@vger.kernel.org \
    --cc=gregkh@linuxfoundation.org \
    --cc=jic23@kernel.org \
    --cc=knaack.h@gmx.de \
    --cc=lars@metafoo.de \
    --cc=linux-iio@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=mark.rutland@arm.com \
    --cc=paul.cercueil@analog.com \
    --cc=pmeerw@pmeerw.net \
    --cc=robh+dt@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).