From: Zhou Yanjie <zhouyanjie@zoho.com>
To: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org, devicetree@vger.kernel.org,
robh+dt@kernel.org, paul.burton@mips.com, paulburton@kernel.org,
jhogan@kernel.org, mripard@kernel.org, shawnguo@kernel.org,
mark.rutland@arm.com, syq@debian.org, ralf@linux-mips.org,
heiko@sntech.de, icenowy@aosc.io,
laurent.pinchart@ideasonboard.com, krzk@kernel.org,
geert+renesas@glider.be, paul@crapouillou.net,
prasannatsmkumar@gmail.com, sernia.zhou@foxmail.com
Subject: [PATCH 1/4] MIPS: Ingenic: initial X1000 support.
Date: Fri, 22 Nov 2019 21:11:26 +0800 [thread overview]
Message-ID: <1574428289-21764-2-git-send-email-zhouyanjie@zoho.com> (raw)
In-Reply-To: <1574428289-21764-1-git-send-email-zhouyanjie@zoho.com>
Support the Ingenic X1000 SoC using the code under arch/mips/jz4740.
This is left unselectable in Kconfig until a X1000 based board is
added in a later commit.
Signed-off-by: Zhou Yanjie <zhouyanjie@zoho.com>
---
arch/mips/boot/dts/ingenic/x1000.dtsi | 161 ++++++++++++++++++++++++++++++++++
arch/mips/jz4740/Kconfig | 6 ++
arch/mips/jz4740/time.c | 4 +-
3 files changed, 170 insertions(+), 1 deletion(-)
create mode 100644 arch/mips/boot/dts/ingenic/x1000.dtsi
diff --git a/arch/mips/boot/dts/ingenic/x1000.dtsi b/arch/mips/boot/dts/ingenic/x1000.dtsi
new file mode 100644
index 0000000..b8658a6
--- /dev/null
+++ b/arch/mips/boot/dts/ingenic/x1000.dtsi
@@ -0,0 +1,161 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <dt-bindings/clock/x1000-cgu.h>
+
+/ {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "ingenic,x1000", "ingenic,x1000e";
+
+ cpuintc: interrupt-controller {
+ #address-cells = <0>;
+ #interrupt-cells = <1>;
+ interrupt-controller;
+ compatible = "mti,cpu-interrupt-controller";
+ };
+
+ intc: interrupt-controller@10001000 {
+ compatible = "ingenic,x1000-intc", "ingenic,jz4780-intc";
+ reg = <0x10001000 0x50>;
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ interrupt-parent = <&cpuintc>;
+ interrupts = <2>;
+ };
+
+ exclk: ext {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ };
+
+ rtclk: rtc {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ };
+
+ cgu: x1000-cgu@10000000 {
+ compatible = "ingenic,x1000-cgu";
+ reg = <0x10000000 0x100>;
+
+ clocks = <&exclk>, <&rtclk>;
+ clock-names = "ext", "rtc";
+
+ #clock-cells = <1>;
+ };
+
+ apb {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <>;
+
+ uart0: serial@10030000 {
+ compatible = "ingenic,x1000-uart";
+ reg = <0x10030000 0x100>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <51>;
+
+ clocks = <&exclk>, <&cgu X1000_CLK_UART0>;
+ clock-names = "baud", "module";
+
+ status = "disabled";
+ };
+
+ uart1: serial@10031000 {
+ compatible = "ingenic,x1000-uart";
+ reg = <0x10031000 0x100>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <50>;
+
+ clocks = <&exclk>, <&cgu X1000_CLK_UART1>;
+ clock-names = "baud", "module";
+
+ status = "disabled";
+ };
+
+ uart2: serial@10032000 {
+ compatible = "ingenic,x1000-uart";
+ reg = <0x10032000 0x100>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <49>;
+
+ clocks = <&exclk>, <&cgu X1000_CLK_UART2>;
+ clock-names = "baud", "module";
+
+ status = "disabled";
+ };
+
+ pinctrl: pin-controller@10010000 {
+ compatible = "ingenic,x1000-pinctrl";
+ reg = <0x10010000 0x800>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ gpa: gpio@0 {
+ compatible = "ingenic,x1000-gpio";
+ reg = <0>;
+
+ gpio-controller;
+ gpio-ranges = <&pinctrl 0 0 32>;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <17>;
+ };
+
+ gpb: gpio@1 {
+ compatible = "ingenic,x1000-gpio";
+ reg = <1>;
+
+ gpio-controller;
+ gpio-ranges = <&pinctrl 0 32 32>;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <16>;
+ };
+
+ gpc: gpio@2 {
+ compatible = "ingenic,x1000-gpio";
+ reg = <2>;
+
+ gpio-controller;
+ gpio-ranges = <&pinctrl 0 64 32>;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <15>;
+ };
+
+ gpd: gpio@3 {
+ compatible = "ingenic,x1000-gpio";
+ reg = <3>;
+
+ gpio-controller;
+ gpio-ranges = <&pinctrl 0 96 32>;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <14>;
+ };
+ };
+ };
+};
diff --git a/arch/mips/jz4740/Kconfig b/arch/mips/jz4740/Kconfig
index 4dd0c44..6b96844 100644
--- a/arch/mips/jz4740/Kconfig
+++ b/arch/mips/jz4740/Kconfig
@@ -33,3 +33,9 @@ config MACH_JZ4780
select MIPS_CPU_SCACHE
select SYS_HAS_CPU_MIPS32_R2
select SYS_SUPPORTS_HIGHMEM
+
+config MACH_X1000
+ bool
+ select MIPS_CPU_SCACHE
+ select SYS_HAS_CPU_MIPS32_R2
+ select SYS_SUPPORTS_HIGHMEM
diff --git a/arch/mips/jz4740/time.c b/arch/mips/jz4740/time.c
index cb768e5..3af6538 100644
--- a/arch/mips/jz4740/time.c
+++ b/arch/mips/jz4740/time.c
@@ -101,7 +101,9 @@ static struct clock_event_device jz4740_clockevent = {
#ifdef CONFIG_MACH_JZ4740
.irq = JZ4740_IRQ_TCU0,
#endif
-#if defined(CONFIG_MACH_JZ4770) || defined(CONFIG_MACH_JZ4780)
+#if defined(CONFIG_MACH_JZ4770) || \
+ defined(CONFIG_MACH_JZ4780) || \
+ defined(CONFIG_MACH_X1000)
.irq = JZ4780_IRQ_TCU2,
#endif
};
--
2.7.4
next prev parent reply other threads:[~2019-11-22 13:13 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-11-22 13:11 Add initial support for Ingenic X1000 SoC and Y&A CU Neo board Zhou Yanjie
2019-11-22 13:11 ` Zhou Yanjie [this message]
2019-11-22 14:36 ` [PATCH 1/4] MIPS: Ingenic: initial X1000 support Paul Cercueil
2019-11-22 15:10 ` Zhou Yanjie
2019-11-22 13:11 ` [PATCH 2/4] dt-bindings: Document yna vendor-prefix Zhou Yanjie
2019-11-22 13:11 ` [PATCH 3/4] dt-bindings: MIPS: Add Ingenic XBurst based boards Zhou Yanjie
2019-11-22 13:11 ` [PATCH 4/4] MIPS: Ingenic: Initial YSH & ATIL CU Neo board support Zhou Yanjie
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1574428289-21764-2-git-send-email-zhouyanjie@zoho.com \
--to=zhouyanjie@zoho.com \
--cc=devicetree@vger.kernel.org \
--cc=geert+renesas@glider.be \
--cc=heiko@sntech.de \
--cc=icenowy@aosc.io \
--cc=jhogan@kernel.org \
--cc=krzk@kernel.org \
--cc=laurent.pinchart@ideasonboard.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mips@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=mripard@kernel.org \
--cc=paul.burton@mips.com \
--cc=paul@crapouillou.net \
--cc=paulburton@kernel.org \
--cc=prasannatsmkumar@gmail.com \
--cc=ralf@linux-mips.org \
--cc=robh+dt@kernel.org \
--cc=sernia.zhou@foxmail.com \
--cc=shawnguo@kernel.org \
--cc=syq@debian.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).